D-Link DVG-5802S User manual

2D-Link DVG-5802S User Manual
Table of Contents
Product Overview........................................................4
Package Contents...................................................4
System Requirements .............................................4
Introduction..............................................................5
Features ..................................................................6
Hardware Overview.................................................7
Connections.......................................................7
LEDs..................................................................8
Installation....................................................................9
Before you Begin.....................................................9
Wireless Installation Considerations......................10
Conguration.............................................................11
Web-based Conguration Utility ............................11
Setup Wizard...................................................12
Manual Conguration.......................................16
Dynamic (Cable) ..........................................16
PPPoE (DSL)...............................................17
PPTP............................................................18
L2TP.............................................................20
Static (assigned by ISP)...............................22
Wireless Settings.............................................23
Network Settings..............................................25
DHCP Server Settings .................................26
DHCP Reservation.......................................27
VoIP Line Settings...........................................28
Virtual Server...................................................30
Port Forwarding...............................................32
Application Rules.............................................33
QoS Engine .....................................................34
Network Filters.................................................36
Access Control.................................................37
Access Control Wizard ....................................37
Website Filters.................................................40
Inbound Filters.................................................41
Firewall Settings ..............................................42
ALG Conguration ...........................................43
VPN Passthrough............................................43
RTSP............................................................43
SIP (VoIP)....................................................43
Router Settings................................................44
Advanced Wireless Settings............................45
Transmit Power............................................45
802.11d Mode..............................................45
WISH Settings .................................................46
Wi-Fi Protected Setup......................................48
Advanced Network Settings.............................50
UPnP............................................................50
Internet Ping Block.......................................50
Internet Port Speed......................................50
Multicast Streams.........................................50
Advanced VoIP................................................51
Administrator Settings......................................57
Change Password........................................52
Table of Contents

3D-Link DVG-5802S User Manual
Table of Contents
Remote Management...................................52
Time Settings...................................................53
SysLog.............................................................54
Email Settings..................................................55
System Settings...............................................56
Update Firmware.............................................57
DDNS...............................................................58
System Check..................................................59
Schedules........................................................60
Device Information...........................................61
Logs.................................................................62
Statistics ..........................................................63
Internet Sessions.............................................63
Wireless...........................................................64
WISH Sessions................................................64
Support............................................................65
Wireless Security.......................................................66
What is WEP? .......................................................66
What is WPA? .......................................................67
Wireless Netwrok Setup Wizard............................68
Manual Wireless Network Setup ...........................70
Congure WEP......................................................70
Congure WPA-Personal (PSK)............................71
Congure WPA-Enterprise (RADIUS) ...................72
Connect to a Wireless Network................................74
Using Windows Vista®..........................................74
Congure Wireless Security ..................................75
Connect Using WCN 2.0 in Windows Vista®..........77
Using Windows®XP...............................................78
Congure WEP......................................................79
Congure WPA-PSK .............................................81
Troubleshooting ........................................................83
Wireless Basics.........................................................87
What is Wireless?..................................................88
Tips........................................................................90
Wireless Modes.....................................................91
Networking Basics ....................................................92
Check your IP address..........................................92
Statically Assign an IP address.............................93
Technical Specications...........................................94

4D-Link DVG-5802S User Manual
Section 1 - Product Overview
• D-Link DVG-5802S WirelessN Gigabit Multimedia
VoIP Gateway
• 2 Non-detachable Antennas
• Power Adapter
• CAT5e Ethernet Cable
• CD-ROM with Installation Wizard, User Manual
System Requirements
• Ethernet-based Cable or DSL Modem
• ComputerswithWindows®,Macintosh®,or Linux-based operatingsystemswithaninstalledEthernet
adapter
• Internet Explorer Version 6.0, Mozilla 1.7.12 (5.0), or Firefox 1.5 and above (for conguration)
• Installation Wizard requires Windows®XP with Service Pack 2
Product Overview
Package Contents
Note: Using a power supply with a different voltage rating than the one included with the DVG-5802S will cause damage and void the
warranty for this product.

5D-Link DVG-5802S User Manual
Section 1 - Product Overview
Introduction
TOTAL PERFORMANCE
Combines award winning router features and Draft 802.11n wireless technology to provide the best wireless performance
TOTAL SECURITY
The most complete set of security features including Active Firewall and WPA2 to protect your network against outside
intruders
TOTAL COVERAGE
Provides greater wireless signal rates even at farther distances for best-in-class Whole Home Coverage.
ULTIMATE PERFORMANCE
TheD-LinkWirelessNGigabitMultimediaVoIPGateway(DVG-5802S)isadraft802.11ncompliantdevicethatdeliversrealworld
performance of up to 14x faster than an 802.11g wireless connection (also faster than a 100Mbps wired Ethernet connection).
Create a secure wireless network to share photos, les, music, video, printers, and network storage throughout your home.
Connect the Wireless N Gigabit Multimedia VoIP Gateway to a cable or DSL modem and share your high-speed Internet access
with everyone on the network. In addition, this Router includes a Quality of Service (QoS) engine that keeps digital phone calls
(VoIP) and online gaming smooth and responsive, providing a better Internet experience.
EXTENDED WHOLE HOME COVERAGE
Powered by 11n technology, this high performance router provides superior Whole Home Coverage while reducing dead spots.
The Wireless N Gigabit Multimedia VoIP Gateway is designed for use in bigger homes and for users who demand higher
performance networking. Add a 11n notebook or desktop adapter and stay connected to your network from virtually anywhere
in your home.
TOTAL NETWORK SECURITY
The Wireless N Gigabit Multimedia VoIP Gateway supports all of the latest wireless security features to prevent unauthorized
access, be it from over the wireless network or from the Internet. Support for WPA and WEP standards ensure that you’ll be able
to use the best possible encryption method, regardless of your client devices. In addition, this Wireless N Gigabit Multimedia
VoIP Gateway utilizes dual active rewalls (SPI and NAT) to prevent potential attacks from across the Internet.
* Maximum wireless signal rate derived from IEEE Standard 802.11g and Draft 802.11n specications. Actual data throughput will vary. Network conditions and
environmental factors, including volume of network trafc, building materials and construction, and network overhead, lower actual data throughput rate. Environmental
conditions will adversely affect wireless signal range.

6D-Link DVG-5802S User Manual
Section 1 - Product Overview
• Faster Wireless Networking -The DVG-5802S providesup to 300Mbps*wireless connectionwith other
802.11n wireless clients. This capability allows users to participate in real-time activities online, such as
video streaming, online gaming, and real-time audio. The performance of this 802.11n wireless router
gives you the freedom of wireless networking at speeds 14x faster than 802.11g.
• Compatible with 802.11b and 802.11g Devices - The DVG-5802S is still fully compatible with the IEEE
802.11b standard, so it can connect with existing 802.11b PCI, USB and Cardbus adapters.
• Advanced Firewall Features - The Web-based user interface displays a number of advanced network
management features including:
• Content Filtering - Easily applied content ltering based on MAC Address, URL, and/or
Domain Name.
• Filter Scheduling - These lters can be scheduled to be active on certain days or for a
duration of hours or minutes.
• Secure Multiple/Concurrent Sessions - The DVG-5802S can pass through VPN sessions.
It supports multiple and concurrent IPSec and PPTP sessions, so users behind the DVG-
5802S can securely access corporate networks.
• User-friendly Setup Wizard - Through its easy-to-use Web-based user interface, the DVG-5802S lets
you control what information is accessible to those on the wireless network, whether from the Internet or
from your company’s server. Congure your router to your specic settings within minutes.
* Maximum wireless signal rate derived from IEEE Standard 802.11g and Draft 802.11n specications. Actual data throughput will vary. Network conditions and
environmental factors, including volume of network trafc, building materials and construction, and network overhead, lower actual data throughput rate. Environmental
conditions will adversely affect wireless signal range.
Features

7D-Link DVG-5802S User Manual
Section 1 - Product Overview
Hardware Overview
Connections
USB
Connect a USB 1.1 or 2.0 ash drive to
congure the wireless settings using WCN.
Storage and Print Server are optional,
please check with your Service provider.
Reset
Pressing the Reset button restores
therouter to itsoriginal factorydefault
settings.
Gigabit LAN Ports (1-7)
Connect Ethernet devices such as
computers, switches, and hubs.
Internet Port
The auto MDI/MDIX Internet port is
theconnection for theEthernet cable
to the cable or DSL modem.
Power Receptor
Receptor for the supplied power
adapter.
Phone Ports
Connects to your phones
using a standard phone
cable (RJ-11).

8D-Link DVG-5802S User Manual
Section 1 - Product Overview
Hardware Overview
LEDs
Power LED
A solid light indicates a proper connection to the power supply.
Status LED
A blinking light indicates that the DVG-5802S is ready.
Local Network LEDs
A solid light indicates a connection to an
Ethernet-enabled computer on ports 1-4.
This LED blinks during data transmission.
USB LED
Insert a USB ash drive with
WCN information. The LED will
blink 3 times if it successfully
transfers the wireless settings.
Internet LED
Asolidlightindicatesconnectionon
the Internet port. This LED blinks
during data transmission.
WLAN LED
A solid light indicates that the wireless
segment is ready. This LED blinks
during wireless data transmission.
WPS LED
A blinking light
indicates that the
H/W WPS bottom
is pushed.

9D-Link DVG-5802S User Manual
Section 2 - Installation
Before you Begin
Installation
This section will walk you through the installation process. Placement of the router is very important. Do not place the
router in an enclosed area such as a closet, cabinet, or in the attic or garage.
Please congure the router with the computer that was last connected directly to your modem. Also, you can only use
the Ethernet port on your modem. If you were using the USB connection before using the router, then you must turn off
your modem, disconnect the USB cable and connect an Ethernet cable to the Internet port on the router, and then turn
the modem back on. In some cases, you may need to call your ISP to change connection types (USB to Ethernet).
If you have DSL and are connecting via PPPoE, make sure you disable or uninstall any PPPoE software such as
WinPoet, Broadjump, or Enternet 300 from your computer or you will not be able to connect to the Internet.

10D-Link DVG-5802S User Manual
Section 2 - Installation
Wireless Installation Considerations
The D-Link wireless router lets you access your network using a wireless connection from virtually anywhere within
the operating range of your wireless network. Keep in mind, however, that the number, thickness and location of
walls, ceilings, or other objects that the wireless signals must pass through, may limit the range. Typical ranges vary
depending on the types of materials and background RF (radio frequency) noise in your home or business. The key
to maximizing wireless range is to follow these basic guidelines:
1. Keep the number of walls and ceilings between the D-Link router and other network devices to a
minimum - each wall or ceiling can reduce your adapter’s range from 3-90 feet (1-30 meters.) Position
your devices so that the number of walls or ceilings is minimized.
2.Be aware of the direct line between network devices. A wall that is 1.5 feet thick (.5 meters), at a
45-degree angle appears to be almost 3 feet (1 meter) thick. At a 2-degree angle it looks over 42 feet
(14 meters) thick! Position devices so that the signal will travel straight through a wall or ceiling (instead
of at an angle) for better reception.
3.BuildingMaterialsmakeadifference.Asolidmetaldooror aluminumstudsmayhavea negativeeffecton
range. Try to position access points, wireless routers, and computers so that the signal passes through
drywall or open doorways. Materials and objects such as glass, steel, metal, walls with insulation, water
(sh tanks), mirrors, le cabinets, brick, and concrete will degrade your wireless signal.
4. Keep your product away (at least 3-6 feet or 1-2 meters) from electrical devices or appliances that
generate RF noise.
5.If you are using 2.4GHz cordless phones or X-10 (wireless products such as ceiling fans, lights, and
home security systems), your wireless connection may degrade dramatically or drop completely. Make
sureyour 2.4GHz phone base is as far awayfromyour wireless devices as possible. The base transmits
a signal even if the phone in not in use.

11D-Link DVG-5802S User Manual
Section 3 - Conguration
Conguration
This section will show you how to congure your new D-Link wireless router using the web-based conguration
utility.
Web-based Conguration Utility
To access the conguration utility, open a web-browser
such as Internet Explorer and enter the IP address of
the router (192.168.0.1).
SelectAdmin fromthedrop-downmenuandthenenter
your password. Leave the password blank by default.
If you get a Page Cannot be Displayed error, please
refer to the Troubleshooting section for assistance.

12D-Link DVG-5802S User Manual
Section 3 - Conguration
Setup Wizard
You may click Setup Wizard to quickly congure your router.
If you want to enter your settings without running the wizard, click
Manual Conguration and skip to page 17.
Click Internet Connection Setup Wizard to begin.
If you want to congure your wireless settings, click WirelessSecurity
Setup Wizard and skip to page 73.
Click Next to continue.
DVG-5802S

13D-Link DVG-5802S User Manual
Section 3 - Conguration
Create a new password and then click Next to continue.
Select your time zone from the drop-down menu and then click Next
to continue.
Select the type of Internet connection you use and then click Next
to continue.

14D-Link DVG-5802S User Manual
Section 3 - Conguration
If you selected Dynamic, you may need to enter the MAC address of the
computerthatwaslastconnecteddirectlytoyourmodem.Ifyouarecurrently
using that computer, click Clone Your PC’s MAC Address and then click
Next to continue.
The Host Name is optional but may be required by some ISPs. The default
host name is the device name of the Router and may be changed.
If you selected PPPoE, enter your PPPoE username and password. Click
Next to continue.
Select Static if your ISP assigned you the IP address, subnet mask,
gateway, and DNS server addresses.
Note: Makesureto removeyourPPPoEsoftwarefromyourcomputer.The
software is no longer needed and will not work through a router.
If you selected PPTP, enter your PPTP username and password. Click
Next to continue.

15D-Link DVG-5802S User Manual
Section 3 - Conguration
Ifyou selectedL2TP,enteryourL2TPusername andpassword.ClickNext
to continue.
If you selected Static, enter your network settings supplied by your Internet
provider. Click Next to continue.
Click Connect to save your settings. Once the router is nished rebooting,
click Continue. Please allow 1-2 minutes to connect.
Close your browser window and reopen it to test your Internet connection.
It may take a few tries to initially connect to the Internet.

16D-Link DVG-5802S User Manual
Section 3 - Conguration
SelectDynamic IP (DHCP) toobtainIPAddress
informationautomatically from yourISP. Select
this option if your ISP does not give you any IP
numbers to use. This option is commonly used
for Cable modem services.
The Host Name is optional but may be required
by some ISPs.
Check the box if you are having problems
obtaining an IP address from your ISP.
Enter the Primary DNS server IP address
assigned by your ISP.
Maximum Transmission Unit - you may need to
change the MTU for optimal performance with
your specic ISP. 1500 is the default MTU.
The default MAC Address is set to the Internet
port’s physical interface MAC address on the
Broadband Router. It is not recommended that
you change the default MAC address unless
required by your ISP. You can use the Clone
Your PC’s MAC Address button to replace
the Internet port’s MAC address with the MAC
address of your Ethernet card.
My Internet
Connection:
Host
Name:
MAC Address:
Manual Conguration
Dynamic (Cable)
DNS
Addresses:
MTU:
Use
Unicasting:
DVG-5802S

17D-Link DVG-5802S User Manual
Section 3 - Conguration
Select PPPoE (Username/Password) from the drop-down menu.
Select Static if your ISP assigned you the IP address, subnet mask,
gateway, and DNS server addresses. In most cases, select Dynamic.
Enter the IP address (Static PPPoE only).
Enter your PPPoE user name.
Enter your PPPoE password and then retype the password in the next
box.
Enter the ISP Service Name (optional).
Select either Always-on, On-Demand, or Manual.
EnterthePrimaryandSecondaryDNSServerAddresses(StaticPPPoE
only).
Enter a maximum idle time during which the Internet connection is maintained during inactivity. To disable this feature,
enable Auto-reconnect.
Maximum Transmission Unit - you may need to change the MTU for optimal performance with your specic ISP. 1492 is
the default MTU.
The default MAC Address is set to the Internet port’s physical interface MAC address on the Broadband Router. It is not
recommended that you change the default MAC address unless required by your ISP. You can use the Clone Your PC’s
MAC Address button to replace the Internet port’s MAC address with the MAC address of your Ethernet card.
My Internet
Connection:
Address Mode:
IP Address:
User Name:
Password:
Service Name:
Reconnection
Mode:
Maximum Idle
Time:
DNS Addresses:
MTU:
MAC Address:
Internet Setup
PPPoE (DSL)
Choose PPPoE (Point to Point Protocol over Ethernet) if your ISP uses a PPPoE connection. Your ISP will provide
you with a username and password. This option is typically used for DSL services. Make sure to remove your PPPoE
software from your computer. The software is no longer needed and will not work through a router.
DVG-5802S

18D-Link DVG-5802S User Manual
Section 3 - Conguration
Select Static if your ISP assigned you the IP address,
subnet mask, gateway, and DNS server addresses. In
most cases, select Dynamic.
Enter the IP address (Static PPTP only).
Enter the Primary and Secondary DNS Server Addresses
(Static PPTP only).
Enter the Gateway IP Address provided by your ISP.
Enter the Server IP provided by your ISP (optional).
Enter your PPTP username.
Enter your PPTP password and then retype the password
in the next box.
Select either Always-on, On-Demand, or Manual.
Enter a maximum idle time during which the Internet
connection is maintained during inactivity. To disable this
feature, enable Auto-reconnect.
The DNS server information will be supplied by your ISP
(Internet Service Provider.)
Address Mode:
PPTP IP
Address:
PPTP Subnet
Mask:
PPTP Gateway:
PPTP Server IP:
Internet Setup
PPTP
Choose PPTP (Point-to-Point-Tunneling Protocol ) if your ISP uses a PPTP connection. Your ISP will provide you with
a username and password. This option is typically used for DSL services.
Username:
Password:
Reconnect Mode:
Maximum Idle
Time:
DNS Servers:
DVG-5802S

19D-Link DVG-5802S User Manual
Section 3 - Conguration
Maximum Transmission Unit - you may need to change the MTU for optimal performance with your specic ISP. 1400
is the default MTU.
The default MAC Address is set to the Internet port’s physical interface MAC address on the Broadband Router. It is not
recommended that you change the default MAC address unless required by your ISP. You can use the Clone Your PC’s
MAC Address button to replace the Internet port’s MAC address with the MAC address of your Ethernet card.
MTU:
MAC Address:

20D-Link DVG-5802S User Manual
Section 3 - Conguration
Select Static if your ISP assigned you the IP address,
subnet mask, gateway, and DNS server addresses. In
most cases, select Dynamic.
Enter the L2TP IP address supplied by your ISP (Static
only).
Enter the Subnet Mask supplied by your ISP (Static
only).
Enter the Gateway IP Address provided by your ISP.
Enter the Server IP provided by your ISP (optional).
Enter your L2TP username.
Enter your L2TP password and then retype the password
in the next box.
Select either Always-on, On-Demand, or Manual.
Enter a maximum idle time during which the Internet
connection is maintained during inactivity. To disable this
feature, enable Auto-reconnect.
Enter the Primary and Secondary DNS Server Addresses
(Static L2TP only).
Address Mode:
L2TP IP Address:
L2TP Subnet Mask:
L2TP Gateway:
L2TP Server IP:
Username:
Password:
Reconnect Mode:
Maximum Idle
Time:
DNS Servers:
Internet Setup
L2TP
Choose L2TP (Layer 2 Tunneling Protocol) if your ISP uses a L2TP connection. Your ISP will provide you with a
username and password. This option is typically used for DSL services.
DVG-5802S