D-NAIL 1.4 User manual

1.4
READ BEFORE USE:
IMPORTANT USER INFORMATION
DIGITAL CONTROLLER
INSTRUCTIONS

CONTROLLER DIRECTIONS
1 Plug power cord into
POWER INPUT (E)
ENSURE HEATER SWITCH (D) IS IN OFF POSITION
BEFORE PLUGGING UNIT INTO OUTLET.
2
POWER SWITCH (D)
turns on controller.
Screen flashes
‘PFA’
if heater is not plugged in.
3Plug D-NAIL ® heater into
HEATER INPUT (A)
Only D-NAIL ® heaters should be used.
Other heaters fit plug, but may not work.
4
HEATER SWITCH (E)
turns on heater.
ENSURE HEATER COILS ARE IN A SAFE POSITION
BEFORE POWERING ON HEATER
CD
E
FG
A Heater Input
B Control Face
C Heater Switch
D Power Switch
E Power Input
F Fuse
(10AMP)
G Power Output
BACK
FRONT
A B
TO CHECK OR REPLACE FUSE:
Push in & twist cap counter-
clockwise to reveal fuse.
If blown, replace with:
10AMP Quick Blow Fuse
TOO HIGH A DRAW WILL BLOW FUSE!
Do not use high power devices such
as: microwave, toaster, refrigerater,
heat press, hairdryer, etc.

SET TEMPERATURE: MUST BE ADJUSTED BEFORE FIRST USE
1 Press
SET
button once to adjust temperature.
Screen will display
‘CLSE’
Pressing
SET
twice will display
‘A 2 S E ’
which is the alarm set point and doesn’t
need adjustment. Default value is 1112.
Pressing
SET
again will return to temperature.
2 Press
UP
and
DOWN
arrows to select temperature.
Screen will display selected temperature.
3 When display stops flashing, temperature is set.
AFTER USE:
TAKE CARE: UNLESS GIVEN TIME TO COOL, HEATER & NAIL WILL BE HOT
1Flip
HEATER SWITCH (C)
to off position.
Heater & Nail will be hot, allow time to cool.
2 To unplug heater: press metal tab above
HEATER INPUT (A)
while gently pulling
heater end. Do not tug on cord.
CLEAN CONTROLLER:
POWER OFF CONTROLLER BEFORE CLEANING
Wipe
CONTROLLER FACE (B)
with a soft, dry
cloth. Other surfaces can be cleaned with a
soft damp cloth (wet with water or isopropyl alcohol).
CONTROL FACE
BUTTONS

CAUTION: IN USE HEATERS ARE HOT
DO NOT TOUCH HEATER COILS
ASSEMBLE HEATER & NAIL:
DO NOT ASSEMBLE WHILE HEATER IS PLUGGED INTO CONTROLLER
DO NOT OVER-TIGHTEN tighten by hand threaded parts until snug
Nail styles, materials & heater size may vary from pictures.
Visit D-Nail.com for examples of other assemblies.

KEEPING NAIL CLEAN:
After every application clean unvaporized
material with dry cotton swab.
Unvaporized material builds up as black residue.
WHEN COOL USE ISOPROPYL ALCOHOL TO CLEAN.
CLEAN BUILD UP INSIDE DISH:
1Heat dish to approximately 900OF for several
minutes, until residue becomes ash.
2Allow nail to cool then clean with dry
cotton swab.
GET THE MOST OUT OF YOUR HEATER:
HEATERS WILL LAST THOUSANDS OF HOURS WITH PROPER USE
A few things will dramatically reduce
the life of a heater, DO NOT:
1100F / 600C


RECOMMENDED HEATER TEMPERATURE:
Lower temperatures are recommended
Halo Dish Deep Dish all Quartz
550-650 F600-650 F650-750 F

[e-mail] OR FACEBOOK.COM/DNAIL710
WARRANTY INFORMATION:
2 YEAR WARRANTY ON ALL PARTS AGAINST FAILURE.
Repair after two years or from accidental
damage can be done at a fair price.
Lifetime warranty option available on D-NAIL.COM
Information from sticker on the bottom of controller is
needed to claim warranty service.
COMPLETE VAPORIZATION KIT INCLUDES:
COIL HEATER
Size may vary
from picture
CONTROL STATION
with power cord.
NAIL
design and
material may vary
from picture