Dacor EF36LNBSS User manual

Use and Care Manual
36 Inch Built-In Refrigerator
Part No. 103676 Rev. F/W10303785
Table of Contents
Refrigerator Safety .........................................................1
Important Information .....................................................2
Model Identification .......................................................2
Before Use ....................................................................3
Refrigerator Operation .............................................. 3-11
Care and Cleaning ................................................. 12-13
Troubleshooting ...................................................... 14-15
Product Data Sheets .....................................................16
Warranty and Service ..................................................17
Notes .........................................................................18
Français .....................................................................19
For use with models:
EF36LNBSS, EF36RNBSS, IF36LNBOL, IF36RNBOL
Style varies -
model EF36RNBSS shown

© 2008 Dacor, all rights reserved

1
Refrigerator Safety
Proper Disposal of Your Refrigerator
IMPORTANT: Child entrapment and suffocation are not problems
of the past. Junked or abandoned refrigerators are still dangerous,
even if they sit out for “just a few days.” If you are getting rid of
your old refrigerator, please follow the instructions below to help
prevent accidents.
Before you throw away your old refrigerator or freezer:
Take off the doors.
Leave the shelves in place so children may not easily climbinside.
You can be killed or seriously injured if you don't immediately
You can be killed or seriously injured if you don't follow
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”
These words mean:
follow instructions.
instructions.
DANGER
WARNING
WARNING
Suffocation Hazard
Remove doors from your old refrigerator.
Failure to do so can result in death or brain damage.
IMPORTANT SAFETY INSTRUCTIONS
WARNING: To reduce the risk of fire, electric shock, or injury when using your refrigerator, follow these basic precautions:
SAVE THESE INSTRUCTIONS
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Disconnect power before servicing.
Replace allparts and panels before operating.
Remove doors from your old refrigerator.
Use nonflammable cleaner.
Keep flammable materials and vapors, such as gasoline,
away from refrigerator.
Use two or more people to move and install refrigerator.
Disconnect power before installing ice maker (on ice maker
kit ready models only).
Use a sturdy glass when dispensing ice (on some models).

2
Important Information
Model Identification
Installer: Please leave this guide with this appliance.
Consumer: Please read and keep this use and care manual for
future reference. This guide provides proper use and maintenance
information. Keep this guide and the sales receipt and/
or cancelled check together for future reference. Proof of
original purchase date is needed for warranty service.
IMPORTANT: If you receive a damaged product, immediately
contact your dealer or builder. Do not install or use a damaged
appliance.
If you have any questions, call:
Dacor Customer Service
[phone] (U.S.A. and Canada)
Monday — Friday 6:00 a.m.to 5:00 p.m.Pacific Time
Web site: www.Dacor.com
Have complete model and serial number identification of your
refrigerator ready. These numbers are found on a serial number
label, located on the right side of the refrigerator liner. Record
these numbers on this page for easy access.
Model number ________________________________________
Serial number ________________________________________
Date of purchase______________________________________
For service and warranty information, see page 17.
Since Dacor constantly improves the quality and performance of
our products, we may be need to make changes to the appliance
without revising this manual.
EF36RNBSS:
Refrigerator with stainless steel
finished doors. Top door opens to
the right.
EF36LNBSS:
Refrigerator with stainless steel
finished doors. Top door opens to
the left.
IF36RNBOL:
Refrigerator with doors designed
to accommodate custom panels
and handles. Top door opens to
the right.
IF36LNBOL:
Refrigerator with doors designed
to accommodate custom panels
and handles. Top door opens to
the left.

3
Removing the Top Grille
Grasp both ends of the top grille.1.
Push the top grille straight up, then pull straight out. Lay the2. grille on a soft surface.
Replacing the Top Grille
Insert the top grille hooks (located on the back of the top grille)1. into the slots on the side trim.
Pull the grille down slightly to lock into place.2.
Turning Power On or Off
Remove the top grille.1.
Press power switch to the on or off position.2.
Replace the top grille.3.
Clean Before Using
After you remove all of the packaging materials, clean the inside
of your refrigerator before using it. See the cleaning instructions in
the Care and Cleaning section.
Important information to know about glass shelves and
covers:
Do not clean glass shelves or covers with warm water when
they are cold. Shelves and covers may break if exposed to
sudden temperature changes or impact, such as bumping.
Tempered glass is designed to shatter into many small,
pebble-size pieces. This is normal. Glass shelves and covers
are heavy. Use both hands when removing them to avoid
dropping.
Turning the Main Power Switch On/Off
If you need to turn the power to your refrigerator on or off,
you must remove the top grille assembly to access the power
switch. Turn the power to the refrigerator off when cleaning your
refrigerator or changing light bulbs.
Remove the Packaging
Remove tape and glue residue from surfaces before turning onthe refrigerator. Rub a small amount of liquid dish soap over
the adhesive with your fingers. Wipe with warm water and dry.
Do not use sharp instruments, rubbing alcohol, flammablefluids or abrasive cleaners to remove tape or glue. These
products can damage the surface of your refrigerator. For
more information, see Important Safety Instructions on page1.
Dispose of/recycle all packaging materials.
Before Use
Refrigerator Operation
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
WARNING
WARNING
Explosion Hazard
Keep flammable materials and vapors, such as
gasoline, away from refrigerator.
Failure to do so can result in death, explosion, or fire.
BB A
A. Top grille
B Cabinet side trim
A
IMPORTANT: Be sure the
main power switch is set to
the On position after cleaning
refrigerator or changing light
bulbs.
A. Power switch

4
Refrigerator Operation
Water Supply Requirements
Read all directions before you begin.
IMPORTANT:
When your refrigerator was installed, the water connectionfrom the water source should have been connected to your
refrigerator. If your refrigerator is not connected to a water
source, see Connect the Water Supply in the installation
instructions. If you have any questions about your water
connection, see the Troubleshooting section or call a licensed,
qualified plumber.
If you turn the refrigerator on before the water line isconnected, turn the ice maker off. See Ice Maker and Storage
Bin in on page 8.
All installations must meet local plumbing code requirements.
Water Pressure
A cold water supply with water pressure between 30 and 120
psi (207 and 827 kPa) is required to operate the ice maker.
If you have questions about your water pressure, see the
Troubleshooting section or call a licensed, qualified plumber.
Reverse Osmosis Water Supply
IMPORTANT: The pressure of the water supply coming out of
a reverse osmosis system going to the water inlet valve of the
refrigerator needs to be between 30 and 120 psi (207 and 827
kPa).
If a reverse osmosis water filtration system is connected to your
cold water supply, the water pressure to the reverse osmosis
system needs to be a minimum of 40 psi (276 kPa).
If the water pressure to the reverse osmosis system is less than
40 psi (276 kPa):
Check to see whether the sediment filter in the reverseosmosis system is blocked. Replace the filter if necessary.
Allow the storage tank on the reverse osmosis system to refillafter heavy usage.
If your refrigerator has a water filter, it may further reducethe water pressure when used in conjunction with a reverse
osmosis system. Remove the water filter. See Replacing the
Water Filter in the Care and Cleaning section.
If you have questions about your water pressure, call a licensed,
qualified plumber.
Water System Preparation
Please read before using the water system.
Immediately after installation, follow the steps below to make sure
that the water system is properly cleaned.
Open the freezer drawer and turn off the ice maker. Slide the1. ice maker On/Off control, located on the left-hand side of the
ice bin, to the OFF (down) position as shown.
NOTE: If your model has a base grille filter system, make sure
the base grille filter is properly installed.
Do not use with water that is microbiologically unsafe or of
unknown quality without adequate disinfection before or after
the system. Systems certified for cyst reduction may be used on
disinfected waters that may contain filterable cysts.
Turn on the ice maker. Slide the ice maker On/Off control,2. located on the left-hand side of the ice bin, to the ON (up)
position. Please refer to Ice Maker and Storage Bin on page 8
for further operating instructions.
Allow 24 hours to produce the first batch of ice.
Before using the ice, fill and discard two full containers ofice to prepare the filter for use.
A
A. On/Off control

5
Refrigerator Operation
Normal Operating Sounds
Your new refrigerator may make sounds that your old one
didn’t make. Because the sounds are new to you, you might be
concerned about them. Most of the new sounds are normal. Hard
surfaces, such as the floor, walls and cabinets, can make the
sounds seem louder. The following describes the kinds of sounds
and what may be making them.
If your refrigerator is equipped with an ice maker, you will heara buzzing sound when the water valve opens to fill the ice
maker for each cycle.
Your refrigerator is designed to run more efficiently to keepyour food items at the desired temperatures and to minimize
energy usage. The high efficiency compressor and fans may
cause your refrigerator to run longer than your old one. You
may also hear a pulsating or high-pitched sound from the
compressor or fans adjusting to optimize performance.
You may hear the evaporator fan motor circulating air throughthe refrigerator and freezer compartments. The fan speed may
increase as you open the doors or add warm food.
Rattling noises may come from the flow of refrigerant, thewater line or items stored on top of the refrigerator.
Water dripping on the defrost heater during a defrost cyclemay cause a sizzling sound.
As each cycle ends, you may hear a gurgling sound due to therefrigerant flowing in your refrigerator.
Contraction and expansion of the inside walls may cause apopping noise.
You may hear air being forced over the condenser by thecondenser fan.
You may hear water running into the drain pan during thedefrost cycle.
You may hear a gurgling sound at the defrost drain after thedoor is closed.
Ensuring Proper Air Circulation
In order to ensure proper temperatures, you need to permit airflow
between the refrigerator and freezer sections. As shown in the
illustration, cool air enters the freezer section through vents in the
rear and top. The air flows forward through the freezer section and
recirculates under the freezer floor. Cool air enters the refrigerator
section through the top, flows down and across shelves to the
doors and recirculates to return
air vents at the bottom.
Do not block any airflow vents. If
the vents are blocked, airflow will
be obstructed and temperature
and moisture problems may
occur.
IMPORTANT: Because air
circulates between both sections,
any odors formed in one section
will transfer to the other. You
must thoroughly clean both
sections to eliminate odors. To
avoid odor transfer and drying
out of food, wrap or cover foods
tightly.
Setting the Controls
The control panel is located inside the refrigerator compartment
on the ceiling.
IMPORTANT:
The refrigerator control adjusts the refrigerator compartmenttemperature. The freezer control adjusts the freezer
compartment temperature.
Wait 24 hours after you turn on the refrigerator before you putfood into it. If you add food before the refrigerator has cooled
completely, your food may spoil.
NOTE: Adjusting the refrigerator and freezer controls to a
lower (colder) setting will not cool the compartments any
faster.
If the temperature is too warm or too cold in the refrigeratoror freezer, first check the air vents to be sure they are not
blocked before adjusting the controls.
The preset settings should be correct for normal householdusage. The controls are set correctly when milk or juice is as
cold as you like and when ice cream is firm.
The actual temperature may differ from the display when adoor is open for an extended period of time.
NOTE: The factory recommended settings are 0°F (-18°C) for
the freezer and 37°F (3°C) for the refrigerator.
Turning the Refrigerator On or Off
Press and hold thePOWER ON/OFF key for 2 seconds.
When the refrigerator comes on, the freezer and refrigerator
temperature displays will light.
To turn the refrigerator off, press and hold thePOWER
ON/OFF key for 2 seconds. The freezer and refrigerator
temperature displays will go dark when the refrigerator is off.
NOTE: After the refrigerator is turned on, the Over
Temperature Audio Alarm and indicator light will activate
every 1½ hours until the refrigerator and freezer temperatures
are below 48°F (9°C) and 15°F (-9°C), respectively, or until the
alarm is turned off. To turn off the audio alarm and indicator
light, see Master Alarm Reset on page 7.
ThePower ON/OFF key on the control panel shuts down the
cooling, lighting, fans and compressors as well as the control
panel lights. To turn the power off completely, use the main
power switch located behind the top grille. See Turning the
Main Power Switch ON/OFF on page 3.
Over temperature
indicator light

6
Water Filter Monitor
Do not use with water that is microbiologically unsafe or of
unknown quality without adequate disinfection before or after
the system. Systems certified for cyst reduction may be used on
disinfected waters that may contain filterable cysts.
The water filter monitor will help you know when it is time to
change your filter. To change the filter, see Replacing the Water
Filter on page 13.
DISPLAY READING: STATUS:
99 percent New filter installed
10 percent Order replacement filter
0 percent or flow decreases Replace filter
A new water filter should display
a reading of 99%. The reading in
the display will decrease as the
filter life is used. When the display
reads 10%, it is time to order
a replacement water filter. It is
recommended that you replace the
filter when the filter display changes
to 0% OR when water flow to your
ice maker decreases noticeably. See
Replacing the Water Filter on page 13.
After replacing the water filter, press RESET and hold it for 2
seconds to change the water filter display to 99 percent.
Max Cool
The Max Cool feature assists with periods of heavy ice usage, full
grocery loads or temporarily warm room temperatures.
Press the MAX COOL key to turn on the Max Cool feature. The
MAX COOL indicator light will remain on for 24 hours unless
manually turned off.
NOTE: The refrigerator temperature display will remain at 34°F
(1°C) and the freezer temperature display will remain at -5°F
(-21°C) while the Max Cool feature is on. After 24 hours, the
refrigerator will automatically return to the previous temperature
settings.
Refrigerator Operation
Setting the Controls (continued)
Setting the Temperature Scale
The indicator light, next the the C° button, is lit when thetemperature scale for the freezer and refrigerator displays is
set to Celsius. To change the displays to Celsius (or back to
Fahrenheit), press the C° button.
Adjusting the Temperature Setting
NOTE: Wait at least 24 hours between adjustments. Re-check the
temperatures before other adjustments are made.
To adjust the temperature setting:
Press the refrigerator or freezerUP () or DOWN () key
until the desired temperature is reached.
NOTE: The adjustable temperature range for the freezer is
-5°F to 6°F (-21°C to -14°C). The adjustable temperature
range for the refrigerator is 34°F to 46°F (1°C to 8°C).
Use the table below for guidance if you need to change the
temperature.
CONDITION/
REASON: TEMPERATURE ADJUSTMENT:
REFRIGERATOR too cold
Not set correctly for conditions REFRIGERATOR Control 1° higher
REFRIGERATOR too warm
High use or room very warm REFRIGERATOR Control 1° lower
FREEZER too cold
Not set correctly for conditions FREEZER Control 1° higher
FREEZER too warm/too little ice.
High use or heavy ice use FREEZER Control 1° lower
Celsius indicator light
Max cool
indicator light

7
Door Open
The DOOR OPEN indicator light will flash, an
alarm will sound and the interior lights will turn
off when a door has been open for longer than
10 minutes. When the door is closed, the audio alarm will reset
and turn off, but the DOOR OPEN indicator light will continue
to flash until the temperature is equal to or below 45°F (7°C)
and 15°F (-9°C) for the refrigerator and freezer compartments,
respectively.
NOTE: To deactivate the audio alarm and indicator light, see
Master Alarm Reset below.
Call Service
If the CALL SERVICE indicator light is flashing,
call for service. See the Warranty and Service
section for information.
NOTE: To deactivate the audio alarm and indicator light, see
Master Alarm Reset.
Master Alarm Reset
Pressing the OVER TEMP RESET key will
shut off the audio alarm, but this does not
affect the indicator light the first time OVER
TEMP RESET is pressed. The indicator light
will shut off once OVER TEMP RESET is
pressed the second time. The audio alarm will
not sound again for the current condition that
caused the alarm until a new condition occurs
or until a master alarm reset is performed.
To perform a master alarm reset press the POWER ON/OFF key
twice or turn the main power switch to the refrigerator off and on
again. See Turning the Main Power Switch On/Off on page 3.
The indicator light will reactivate after you press the OVER TEMP
RESET key if the condition that caused the alarm is still present.
See Over Temperature, Door Open or Call Service.
Holiday Mode
The Holiday mode feature is designed for the traveler or for
those whose religious observances require turning off the lights
and ice maker. When you select this feature, the ice maker will
be disabled and the interior lights will turn off. The temperature
settings remain unchanged. On some models, the Holiday Mode
feature doesn’t disable the ice and water dispenser. For these
models the lock button can be used to disable the ice and water
functions, but depressing the ice or water lever will still turn on
the dispenser light. For most efficient refrigerator operation, it
is recommended to exit the Holiday Mode when it is no longer
required.
Press theHOLIDAY key to turn on the Holiday mode feature.
This feature will remain on until you press the HOLIDAY key
again.
NOTE: If the Max Cool feature has been selected prior to
turning on the Holiday Mode feature, the temperature settings
will remain at 34°F (1°C) and -5°F (-21°C) for the refrigerator
and freezer compartments, respectively, until the Max Cool
feature time (24 hours) is up. The refrigerator will then return
to the previous temperature settings chosen prior to turning on
the Max Cool feature, but the lights and ice maker will remain
off until the Holiday key is pressed again.
Alarms
Over Temperature
The Over Temperature feature is designed to let you know when
either the refrigerator temperature rises above 48°F (9°C) or
the freezer temperature rises above 15°F (-9°C) for longer than
1½ hours. The audio alarm will shut off automatically when the
temperature returns to normal, but the indicator light will continue
to flash to let you know that an over temperature condition has
occurred.
If the over temperature condition is still present when an Over
Temperature Reset is performed, the indicator light will continue
to reactivate every 1½ hours until refrigerator and freezer
temperatures are below 48°F (9°C) and 15°F (-9°C), respectively.
IMPORTANT: If the Over Temperature Alarm activates, your
food may spoil. See Power Interruptions on page 10. Minimize
door openings until
temperatures return to
normal.
NOTE: To deactivate
the audio alarm and
indicator light, see
Master Alarm Reset.
Refrigerator Operation
Holiday mode
indicator light
Over temperature
indicator light

8
Refrigerator Operation
Ice Maker and Storage Bin
Turning the Ice Maker On and Off
The ice maker On/Off control is located on the left-hand side of
the ice bin.
To turn on the ice maker, slide the ice maker On/Off control to1. the ON (up) position.
NOTE: Your ice maker has an automatic shutoff. As ice is
made, the ice cubes will fill the ice storage bin. The ice maker
sensors will automatically stop ice production, but the ice
maker control will remain in the ON (up) position.
To manually turn off the ice maker, slide the ice maker On/Off2. control to the OFF (down) position as shown.
Ice Storage Bin Care
Remove the ice bin. See page 10 for instructions.1.
Empty the ice bin. Use warm water to melt the ice if2. necessary.
NOTE: Do not use anything sharp to break up the ice in the
bin. This can cause damage to the ice container and the
dispenser mechanism.
Wash ice bin with warm water and a mild detergent, rinse well3. and dry thoroughly. Do not use harsh or abrasive cleaners or
solvents.
IMPORTANT:
Allow 24 hours to produce the first batch of ice.
Before using the ice, fill and discard two full containers of iceto prepare the filter for use.
It may take 3 to 4 days for the ice bin to completely fill, if noice is used.
The quality of your ice will be only as good as the quality ofthe water supplied to your ice maker.
Avoid connecting the ice maker to a softened water supply.Water softener chemicals (such as salt) can damage parts of
the ice maker and lead to poor quality ice. If a softened water
supply cannot be avoided, make sure the water softener is
operating properly and is well maintained.
It is normal for the ice cubes to be attached at the corners.They will break apart easily.
Do not store anything inside the ice bin.
Refrigerator Storage
Important information to know about glass shelves and
covers:
Do not clean glass shelves or covers with warm water when
they are cold. Shelves and covers may break if exposed to
sudden temperature changes or impact, such as bumping.
Tempered glass is designed to shatter into many small,
pebble-size pieces. This is normal. Glass shelves and covers
are heavy. Use both hands when removing them to avoid
dropping.
The shelves and compartments in your refrigerator are adjustable
and/or removable to meet your individual storage needs and to
make them easier to clean.
Storing similar food items together in your refrigerator and
adjusting the shelves compartments to fit different heights of
items will make finding the exact item you want easier. It will also
reduce the amount of time the refrigerator door is open, and help
save energy.
Shelves and Shelf Frames
To remove and replace a shelf/frame:
Remove the shelf/frame by tilting it up at the front and lifting it1. out of the shelf supports. Pull the shelf straight out.
Replace the shelf/frame by guiding the rear shelf hooks into2. the shelf supports. Tilt the front of the shelf up until the rear
shelf hooks drop into the shelf supports.
Lower the front of the shelf and check to make sure that the3. shelf is securely in position.
Deli and Crisper Pans
The refrigerator has one deli pan and one crisper pan. The crisper
pan is the larger of the pans. The crisper pan is good for larger
produce items.
A
A. On/Off control
B
A
A. Crisper Pan
B Deli pan