Daewoo DAFPS-3 User manual

Manufactured under license of Daewoo International Corporation, Korea
www.daewoopowerproducts.com
USER'S MANUAL
DAFPS-3
Float swich
The device, connected to an electrical through an electrical cable, is used for the auto-control and
no water protection of the water tower and water pool.
1. TECHNICAL DATA
Rated voltage: AC 125V/250V
Max current: 16(8) A
Frequency: 50-60 Hz
Max operating temperature: 55°C
Protection grade: IP68
2. INSTALLATION
1. Fix the counterweight on the power cable to control water level.(Counterweight is only provided at
request.)
2. Connect the electrical cable with the electrical pump and then fix it inside the water tank.
3. The length of the cable section between the fixation point of the device and the device body
determines the water level.
4. The terminal of the electrical cable shall never be immersed into water during installation.
3. INSTRUCTION FOR USAGE
1. Instruction for water-filling operation:
Connect the blue cable of the floating the control to the electrical pump and the yellow-green or
black one to a neutral as shown in Fig.1 for water filling operation(The brown cable shall be kept
insulated.) For detailed installation instruction,please refer to Fig.2 and 3.
Function of Fig2&3:Electrical pump begins to fill water when water in water tank drops to a certain
level and stops its working when water rises to certain level.
2. Instruction for water-emptying operation:
Connect the brown cable to the water pump and the yellow-green or black one to a neutral wire as
shown in Fig.4 for water emptying operation（The blue cable shall be kept insulated.）For detailed
installation instruction, please refer to Fig.5 and 6.
4. INSTRUCTION FOR AUTO-FILLING & AUTO-EMPTYING
5. ILLUSTRATION COUNTERWEIGHT INSTALLATION:
6. WARNING
1. The power supply cable is an integrate part of the device. Should the cable be found to be dama-
ged the device is to be replaced. Repairs to the cable itself are not possible.
2. The cable terminal must be never immersed into water.
3. The cable that is not used must be correctly insulated.
4. The electrical pump must be grounded to avoid any accidents.

INDEX
1. TECHNICAL DATA .................................................................................................................................. 2
2. INSTALLATION ........................................................................................................................................ 2
3 . INSTRUCTION FOR USAGE ................................................................................................................... 2
4 . INSTRUCTION FOR AUTO-FILLING & AUTO-EMPTYING ................................................................... 3
5. ILLUSTRATION COUNTERWEIGHT INSTALLATION ............................................................................ 3
6. WARNING ................................................................................................................................................ 4
WARRANTY
................................................................................................................................................. 5
The device, connected to an electrical through an electrical cable, is used for the auto-control and
no water protection of the water tower and water pool.
1. TECHNICAL DATA
Rated voltage: AC 125V/250V
Max current: 16(8) A
Frequency: 50-60 Hz
Max operating temperature: 55°C
Protection grade: IP68
2. INSTALLATION
1. Fix the counterweight on the power cable to control water level.(Counterweight is only provided at
request.)
2. Connect the electrical cable with the electrical pump and then fix it inside the water tank.
3. The length of the cable section between the fixation point of the device and the device body
determines the water level.
4. The terminal of the electrical cable shall never be immersed into water during installation.
3. INSTRUCTION FOR USAGE
1. Instruction for water-filling operation:
Connect the blue cable of the floating the control to the electrical pump and the yellow-green or
black one to a neutral as shown in Fig.1 for water filling operation(The brown cable shall be kept
insulated.) For detailed installation instruction,please refer to Fig.2 and 3.
Function of Fig2&3:Electrical pump begins to fill water when water in water tank drops to a certain
level and stops its working when water rises to certain level.
2. Instruction for water-emptying operation:
Connect the brown cable to the water pump and the yellow-green or black one to a neutral wire as
shown in Fig.4 for water emptying operation（The blue cable shall be kept insulated.）For detailed
installation instruction, please refer to Fig.5 and 6.
4. INSTRUCTION FOR AUTO-FILLING & AUTO-EMPTYING
5. ILLUSTRATION COUNTERWEIGHT INSTALLATION:
6. WARNING
1. The power supply cable is an integrate part of the device. Should the cable be found to be dama-
ged the device is to be replaced. Repairs to the cable itself are not possible.
2. The cable terminal must be never immersed into water.
3. The cable that is not used must be correctly insulated.
4. The electrical pump must be grounded to avoid any accidents.
1

EN
The device, connected to an electrical through an electrical cable, is used for the auto-control and
no water protection of the water tower and water pool.
1. TECHNICAL DATA
Rated voltage: AC 125V/250V
Max current: 16(8) A
Frequency: 50-60 Hz
Max operating temperature: 55°C
Protection grade: IP68
2. INSTALLATION
1. Fix the counterweight on the power cable to control water level.(Counterweight is only provided at
request.)
2. Connect the electrical cable with the electrical pump and then fix it inside the water tank.
3. The length of the cable section between the fixation point of the device and the device body
determines the water level.
4. The terminal of the electrical cable shall never be immersed into water during installation.
3. INSTRUCTION FOR USAGE
1. Instruction for water-filling operation:
Connect the blue cable of the floating the control to the electrical pump and the yellow-green or
black one to a neutral as shown in Fig.1 for water filling operation(The brown cable shall be kept
insulated.) For detailed installation instruction,please refer to Fig.2 and 3.
Function of Fig2&3:Electrical pump begins to fill water when water in water tank drops to a certain
level and stops its working when water rises to certain level.
2. Instruction for water-emptying operation:
Connect the brown cable to the water pump and the yellow-green or black one to a neutral wire as
shown in Fig.4 for water emptying operation（The blue cable shall be kept insulated.）For detailed
installation instruction, please refer to Fig.5 and 6.
4. INSTRUCTION FOR AUTO-FILLING & AUTO-EMPTYING
5. ILLUSTRATION COUNTERWEIGHT INSTALLATION:
6. WARNING
1. The power supply cable is an integrate part of the device. Should the cable be found to be dama-
ged the device is to be replaced. Repairs to the cable itself are not possible.
2. The cable terminal must be never immersed into water.
3. The cable that is not used must be correctly insulated.
4. The electrical pump must be grounded to avoid any accidents.
Fig 1 Fig 2 Fig 3
Water pool
Water towerWater tower
2

The device, connected to an electrical through an electrical cable, is used for the auto-control and
no water protection of the water tower and water pool.
1. TECHNICAL DATA
Rated voltage: AC 125V/250V
Max current: 16(8) A
Frequency: 50-60 Hz
Max operating temperature: 55°C
Protection grade: IP68
2. INSTALLATION
1. Fix the counterweight on the power cable to control water level.(Counterweight is only provided at
request.)
2. Connect the electrical cable with the electrical pump and then fix it inside the water tank.
3. The length of the cable section between the fixation point of the device and the device body
determines the water level.
4. The terminal of the electrical cable shall never be immersed into water during installation.
3. INSTRUCTION FOR USAGE
1. Instruction for water-filling operation:
Connect the blue cable of the floating the control to the electrical pump and the yellow-green or
black one to a neutral as shown in Fig.1 for water filling operation(The brown cable shall be kept
insulated.) For detailed installation instruction,please refer to Fig.2 and 3.
Function of Fig2&3:Electrical pump begins to fill water when water in water tank drops to a certain
level and stops its working when water rises to certain level.
2. Instruction for water-emptying operation:
Connect the brown cable to the water pump and the yellow-green or black one to a neutral wire as
shown in Fig.4 for water emptying operation（The blue cable shall be kept insulated.）For detailed
installation instruction, please refer to Fig.5 and 6.
4. INSTRUCTION FOR AUTO-FILLING & AUTO-EMPTYING
5. ILLUSTRATION COUNTERWEIGHT INSTALLATION:
6. WARNING
1. The power supply cable is an integrate part of the device. Should the cable be found to be dama-
ged the device is to be replaced. Repairs to the cable itself are not possible.
2. The cable terminal must be never immersed into water.
3. The cable that is not used must be correctly insulated.
4. The electrical pump must be grounded to avoid any accidents.
Fig 4 Fig 5 Fig 6
Fig.7: Shows the auto-switch between filling and emptying water.
Which is an extension of the two basic functions.
Please refer to the basic functions for details.
Fig 7
Fig 8
Fig.8: Peel the plastic ring off the counterweight
before installation and set the ring around the cable,
then insert the cable from the conic part into the counterweight
and fix it with moderate pressure at the fixing end.
3

EN
The device, connected to an electrical through an electrical cable, is used for the auto-control and
no water protection of the water tower and water pool.
1. TECHNICAL DATA
Rated voltage: AC 125V/250V
Max current: 16(8) A
Frequency: 50-60 Hz
Max operating temperature: 55°C
Protection grade: IP68
2. INSTALLATION
1. Fix the counterweight on the power cable to control water level.(Counterweight is only provided at
request.)
2. Connect the electrical cable with the electrical pump and then fix it inside the water tank.
3. The length of the cable section between the fixation point of the device and the device body
determines the water level.
4. The terminal of the electrical cable shall never be immersed into water during installation.
3. INSTRUCTION FOR USAGE
1. Instruction for water-filling operation:
Connect the blue cable of the floating the control to the electrical pump and the yellow-green or
black one to a neutral as shown in Fig.1 for water filling operation(The brown cable shall be kept
insulated.) For detailed installation instruction,please refer to Fig.2 and 3.
Function of Fig2&3:Electrical pump begins to fill water when water in water tank drops to a certain
level and stops its working when water rises to certain level.
2. Instruction for water-emptying operation:
Connect the brown cable to the water pump and the yellow-green or black one to a neutral wire as
shown in Fig.4 for water emptying operation（The blue cable shall be kept insulated.）For detailed
installation instruction, please refer to Fig.5 and 6.
4. INSTRUCTION FOR AUTO-FILLING & AUTO-EMPTYING
5. ILLUSTRATION COUNTERWEIGHT INSTALLATION:
6. WARNING
1. The power supply cable is an integrate part of the device. Should the cable be found to be dama-
ged the device is to be replaced. Repairs to the cable itself are not possible.
2. The cable terminal must be never immersed into water.
3. The cable that is not used must be correctly insulated.
4. The electrical pump must be grounded to avoid any accidents.
4

GUARANTEE
WARRANTY DOES NOT COVER
Product model
Serial number
Username
Date of sale
Company
Client's signature
The warranty period starts from the date of sale of the products and covers 1 year for all power products.
During the warranty period, free failures caused due to the use of poor-quality materials in the production and
manufacturer workmanship admitted fault are removed. The guarantee comes into force only when warranty card
and cutting coupons are properly filled. The product is accepted for repair in its pure form and full completeness.
• Mechanical damage (cracks, chips, etc.) and damage
caused by exposure to aggressive media, foreign objects
inside the unit and air vents, as well as for damage occurred
as a result of improper storage (corrosion of metal parts);
• Failures caused by overloading or product misuse, use of
the product for other purposes. A sure sign of overload
products is melting or discoloration of parts due to the high
temperature, simultaneous failure of two or more nodes,
teaser on the surfaces of the cylinder and the piston or
destruction of piston rings. Also, the warranty does not
cover failure of the automatic voltage regulator due to
incorrect operation;
• Failure caused by clogging of the fuel and cooling systems;
• Wearing parts (carbon brushes, belts, rubber seals, oil
seals, shock absorbers, springs, clutches, spark plugs,
mufflers, nozzles, pulleys, guide rollers, cables, recoil starter,
chucks, collets, removable batteries, filters and safety
elements, grease, removable devices, equipment, knives,
drills, etc.);
• Electrical cables with mechanical and thermal damage;
• Product opened or repaired by a non-authorized service center.
• Prevention, care products (cleaning, washing, lubrication,
etc.), installation and configuration of the product;
• Natural wear products (production share);
• Failures caused by using the product for the needs related
to business activities;
• If the warranty card is empty or missing seal (stamp) of the Seller;
• The absence of the holder's signature on the warranty card.
WARRANTY CARD
The product is in good conditions and fully complete. Read and agree the terms of the warranty.
Product
Model
Company
Date
of sale
Product
Model
Company
Date
of sale
The device, connected to an electrical through an electrical cable, is used for the auto-control and
no water protection of the water tower and water pool.
1. TECHNICAL DATA
Rated voltage: AC 125V/250V
Max current: 16(8) A
Frequency: 50-60 Hz
Max operating temperature: 55°C
Protection grade: IP68
2. INSTALLATION
1. Fix the counterweight on the power cable to control water level.(Counterweight is only provided at
request.)
2. Connect the electrical cable with the electrical pump and then fix it inside the water tank.
3. The length of the cable section between the fixation point of the device and the device body
determines the water level.
4. The terminal of the electrical cable shall never be immersed into water during installation.
3. INSTRUCTION FOR USAGE
1. Instruction for water-filling operation:
Connect the blue cable of the floating the control to the electrical pump and the yellow-green or
black one to a neutral as shown in Fig.1 for water filling operation(The brown cable shall be kept
insulated.) For detailed installation instruction,please refer to Fig.2 and 3.
Function of Fig2&3:Electrical pump begins to fill water when water in water tank drops to a certain
level and stops its working when water rises to certain level.
2. Instruction for water-emptying operation:
Connect the brown cable to the water pump and the yellow-green or black one to a neutral wire as
shown in Fig.4 for water emptying operation（The blue cable shall be kept insulated.）For detailed
installation instruction, please refer to Fig.5 and 6.
4. INSTRUCTION FOR AUTO-FILLING & AUTO-EMPTYING
5. ILLUSTRATION COUNTERWEIGHT INSTALLATION:
6. WARNING
1. The power supply cable is an integrate part of the device. Should the cable be found to be dama-
ged the device is to be replaced. Repairs to the cable itself are not possible.
2. The cable terminal must be never immersed into water.
3. The cable that is not used must be correctly insulated.
4. The electrical pump must be grounded to avoid any accidents.

www.daewoopowerproducts.com
Manufactured under license of Daewoo International Corporation, Korea