Daewoo DTQ-2133SSFN User manual

COLOR TELEVISION
INSTRUCTION MANUAL
DTQ-2133SSN
DTQ-2133SSFN
P/N:48586001E222-R1

CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended
to alert the user to the presence of uninsulated dangerous voltage within the
product s enclosure that may be of sufficient magnitude to constitute a risk electric shock.
The exclamation point within an equilateral triangle is intended to alert the user to the
presence of important operating and servicing instructions in the literature accompany-
ing the appliance.
WARNING
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
CAUTION
CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE MANUFACTURER COULD VOID
THE USER S AUTHORITY TO OPERATE THE EQUIPMENT.
NOTE TO CATV SYSTEM INSTALLER
THIS REMINDER IS PROVIDED TO CALL THE CATV SYSTEM INSTALLER'S ATTENTION TO ARTICLE
820-40 OF THE NEC THAT PROVIDES GUIDELINES FOR PROPER GROUNDING AND, IN PARTICULAR,
SPECIFIES THAT THE CABLE GROUND SHALL BE CONNECTED TO THE GROUNDING SYSTEM OF THE
BUILDING, AS CLOSE TO THE POINT OF CABLE ENTRY AS PRACTICAL.
CAUTION
To provide power to the TV, fully insert the AC plug into a standard 110V~, 60Hz polarized outlet.
(To provide power to the TV, fully insert the AC plug into a standard 90-250V~, 50/60Hz polarized outlet.)
NOTE
Never connect the plug to an electrical source other than one providing 110V~, 60Hz(90-250V, 50/60Hz) power. Use
only the attached power cord. If the polarized AC cord does not fit into a non-polarized outlet, do not cut or file the
blade. You are responsible for having the obsolete outlet replaced with a polarized outlet.
If you feel a static discharge when touching the unit, and the unit does not function, simply unplug the unit from the out-
let. When you plug the unit back in, it should work normally.
Do not install power cords near any heating element or cooking appliances.

CONTENTS
1
TableofContents
Table of Contents
Important Safeguards 2
Chapter 1: Overview of Your Equipment 4
Your TV's Front Panel 4
Your TV's Back Panel 5
Your Remote Controls 6
Installing your remote control batteries 7
Notes 7
Chapter 2: Connecting an Antenna or Cable to Your TV 8
Connecting an Antenna 8
Connecting a Cable System 9
Connecting Other Pieces of Equipment 10
Safety Note 10
Chapter 3: Operating Your TV 11
Turning your TV On 11
Programming Your TV's Channel Memory 11
Changing Channels 12
Changing the Volume 12
Changing The TV's Channel Memory 13
Adding/Deleting a channel to memory 13
Displaying the Current Channel 13
Changing the TV s Input 14
Adjusting Video Settings 15
Returning to the factory settings 16
Descriptions of video settings 16
Chapter 4: Using Timer Functions 17
Setting the Clock 17
Setting the Wake-Up Time 17
Setting the Off Time 18
Canceling the Wake-Up Time or Off Time 18
Setting the Sleep Timer 19
Chapter 5 : Additional Features 20
Changing the Language of the On-Screen Menus 20
Captioning 20
CC on Mute 21
Power Restore 21
Parental Control Settings 22
Description of Parental Control Settings 23
Chapter 6 : Troubleshooting 24

2
ImportantSafeguards
SAFETY
IMPORTANT SAFEGUARDS
PLEASE READ ALL THESE INSTRUCTIONS REGARDING YOUR TELEVISION EQUIPMENT
AND RETAIN FOR FUTURE REFERENCE. FOLLOW ALL WARNINGS AND INSTRUCTIONS
MARKED ON THE TV RECEIVER.
1Read all of these instructions.
2Save these instructions for later use.
3Unplug this television equipment from the wall
outlet before cleaning. Do not use liquid cleaners
or aerosol cleaners. Use a damp cloth for cleaning.
4Do not use attachments not recommended by the
television equipment manufacturer as they may
result in the risk of fire, electric shock or other
personal injury.
5Do not use this television equipment near water,
for example, near a bathtub, washbowl, kitchen
sink, or laundry tub, in a wet basement, or near a
swimming pool, or the like.
6Do not place this television equipment on an
unstable cart, stand, or table. The television
equipment may fall, causing serious injury to a
child or adult, and serious damage to the quipment .
Use only with a cart or stand recommended by
the manufacturer, or sold with the television
equipment. Wall or shelf mounting should follow
the manufacturer's instructions, and should use a
mounting kit approved by the manufacturer.
6A An appliance and cart combination should be
moved with care. Quick stops, excessive force,
and uneven surfaces may cause the appliance and
cart combination to overturn.
7Slots and openings in the cabinet and the back or
bottom are provided for ventilation and to ensure
reliable operation of the television equipment;
and to protect it from overheating, these opening,
must not be blocked or covered. The opening
should never be blocked by placing the television
equipment on a bed, sofa, rug, or other similar
surface. (This equipment should never be placed
near or over a radiator or heat register.) This tele-
vision equipment should not be placed in a
built-in installation such as a bookcase unless
proper ventilation is provided.
8This television equipment should be operated
only from the type of power source indicated on
the marking label. If you are not sure of the type
of power supplied to your home, consult your
television dealer or local power company.
9This television equipment is equipped with a
polarized alternating current line plug (a plug
having one blade wider than the other). This plug
will fit into the power outlet only one way. This
is a safety feature. If you are unable to insert the
plug fully into the outlet, try reversing the plug.
If the plug should still fail to fit, contact your
electrician to replace your obsolete outlet. Do not
defeat the safety purpose of the polarized plug.
10 Do not allow anything to rest on the power cord.
Do not locate this television equipment where
the cord will be abused by persons walking on it.
11 Follow all warnings and instructions marked on
the television equipment.
12 For added protection for this television equip-
ment during a lightning storm, or when it is left
unattended and unused for long periods of time,
unplug it from the wall outlet and disconnect the
antenna or cable system. This will prevent damage
to the equipment due to lightning and power-line
surges.

3
ImportantSafeguards
13 An outside antenna system should not be located
in the vicinity of overhead power lines or other
electric light or power circuits, or where it can fall
into such power lines or circuits. When installing
an outside antenna system, extreme care should be
taken to keep from touching such power lines or
circuits as contact with them might be fatal.
14 Do not overload wall outlets and extension cords
as this can result in fire or electric shock.
15 Never push objects of any kind into this television
equipment through openings as they may touch
dangerous voltage points or short-out parts that
could result in a fire or electric shock. Never spill
liquid of any kind on the television equipment.
16
Do not attempt to service this television equipment
yourself as opening or removing covers may
expose you to dangerous voltage or other hazards.
Refer all servicing to qualified service personnel.
17 Unplug this television equipment from the wall
outlet and refer servicing to qualified service per-
sonnel under the following conditions:
(a)
When the power-supply cord or plug is damaged
or frayed.
(b) If liquid has been spilled, or objects have fallen
into the television equipment.
(c) If the television equipment has been exposed to
rain or water.
(d) If the television equipment does not operate
normally by following the operating instructions.
Adjust only those controls that are covered by the
operating instructions as an improper
adjustment
of other controls may result in damage and will
often require extensive work by a qualified
technician to restore the TV receiver to its normal
operation.
(e) If the television equipment has been dropped or
the cabinet has been damaged.
(f) When the television equipment exhibits a dis-
tinct change in performance - this indicates a
need for service.
18 When replacement parts are required, be sure the
service technician has used replacement parts
specified by the manufacturer that have the same
characteristics as the original part. Unauthorized
substitutions may result in fire, electric shock or
other hazards.
19 Upon completion of any service or repairs to this
television equipment, ask the service technician
to perform safety checks to determine that the
television is in a safe operating condition.
20
If an outside antenna or cable system is connected
to the television receiver, be sure the antenna or
cable system is grounded so as to provided some
protection against voltage surges and built-up
static charges.

4
Chapter 1 : Overview of Your Equipment
CHAPTER 1
Overview of Your Equipment
Your TV comes with a remote control. The section below summarizes the buttons, controls, and
terminals that you will use with your TV.
Your TV's Front Panel
1 MAIN POWER
Use this button to stand-by your TV.
2 POWER
Use this button to turn your TV on or off.
3CH
Use these buttons to change channels on your TV, or to select items in the menu system.
4 VOL
Use these buttons to change your TV's volume, to activate selections in the menu system,
or to change audio and video settings.
5 MENU
Use this button to turn the TV's menu system on and off.
6 STAND-BY(red) indicator
This indicator lights up when the power is off.
7 Remote control receiver
This receiver receives a signal from your remote control. Do not block it.
8 VIDEO IN jack
Use this jack to receive a video signal from another A/V component.
9 AUDIO IN jack
Use this jack to receive an audio signal from another A/V component.
10 HEADPHONE jack
Use this jack to receive an audio signal from your TV.
MAIN
POWER CH VOL MENU
VIDEO POWER
HEADPHONE
AUDIO STAND-BY
12
345
67
8910

Your TV's Back Panel
1 Antenna terminal(ANT)
Use this terminal to attach an antenna or cable system to your TV.
2 AUDIO IN
This terminal allows the TV to receive an audio sighal from another component, such as a VCR.
3 VIDEO IN
This terminal allows the TV to receive a video signal from another component, such as a VCR.
12 3
ANT VIDEO
AUDIO
5
Chapter 1 : Overview of Your Equipment

6
Chapter 1 : Overview of Your Equipment
Your Remote Control
1. POWER
Use this button to turn your TV on or off.
2. MUTE
Use to turn the TV’s sound on and off.
3. WCHV
Use these buttons to change channels on your TV,
or select items in the menu system.
4. CVOLB
Use these buttons to change your TV's volume, to
activate selections in the menu system, or to
change audio and video settings.
5. MENU
Use this button to turn the TV’s menu system on
and off.
6. DISPLAY
Use this button to display the channel
number and status.
7. INPUT
Use this button to select the TV’s signal source.
8. VIDEO
Use this button to display video adjustment items.
9. 0-9
Use these buttons to change channels.
10. SLEEP
Use this button to program the TV to turn off after
a certain time.
11. PREVIOUS
Use this button to return to the previous channel
you were watching.

7
Chapter 1 : Overview of Your Equipment
Installing your remote control batteries
1Open the battery compartment on the back of the remote control.
2Install two AAA-size batteries (not included) as shown. Make sure the + and - terminals
are oriented correctly.
3Replace the cover.
Notes
Do not mix different types of batteries, or mix an old and a new battery.
Remove and replace weak batteries. Weak batteries can leak and damage your controller.
Dispose of batteries properly; never throw them into a fire.
Point your remote at the receiver on the center of the front of the TV. Make sure the receiver is
not blocked.
The remote control can operate up to 30 feet away from the TV, if you are directly facing the
front of the TV. Operating distance diminishes as you move to the sides of the TV.

8
CHAPTER 2
Chapter 2 : Connecting an Antenna or Cable to Your TV
Connecting an Antenna or Cable to Your TV
Your TV will provide you with the best performance if you connect it to an external antenna or
cable system. Follow the directions below make this connection. Please note that you will nor-
mally only have to make one of the connections shown below, not all of them.
All connections will be made to the antenna terminal on the back of your TV. The antenna ter-
minal is a silver metal post partially surrounded by two plastic tabs. For help in locating the
antenna terminal, see Your TV's Back Panel on page 5.
Connecting an Antenna
If your antenna ends in a single coaxial lead, simply
press or screw the cable onto the antenna terminal on the
back of your TV.
If your antenna ends in a pair of 300 ohm twin leads,you must use a 300-ohm/75-ohm
adapter(available at your local electronics store). Place the leads underneath the screws on the
adapter, tighten the screws, then press the adapter onto the antenna terminal on the back of the TV .

9
Chapter 2 : Connecting an Antenna or Cable to Your TV
Antennas with two sets of leads
You might have two sets of leads from your antenna system, especially if you have one antenna
for VHF signals and one antenna for UHF signals.
If your antenna system has both a coaxial lead and twin 300-ohm leads, you must obtain a
combiner (available at your local electronics store). Press or screw the coaxial lead onto the
combiner; place the twin leads underneath the screws on the combiner and tighten the screws.
Press the cable from combiner onto the antenna terminal on the back of your TV.
If your antenna system has two sets of twin 300-ohm leads, you must obtain a combiner
(available at your local electronics store). Place one set of twin leads underneath the screws on
the combiner and tighten the screws. Do the same with the other set of twin leads. Press the
cable from the combiner onto antenna terminal on the back of your TV.
Connecting a cable system
If your cable set-up is not described below, please
contact your cable company for more information.
If your cable system does not require the use
of a cable box,simply press or screw the incom-
ing cable onto the antenna terminal on the back
your TV.

10
Chapter 2 : Connecting an Antenna or Cable to Your TV
If your cable system requires you to use a converter box for all channels, connect the incom-
ing cable to the IN terminal on the converter box. Connect another cable between the OUT ter-
minal on the converter box and the antenna terminal on the TV. You will need to keep your TV
tuned to channel 3 or 4 and change channels using the converter box.
If your cable system only requires you to use a converter box for some channels (i. e.
pay-TV channels), follow these steps: Find the primary incoming coaxial cable. Plug this cable
into a splitter (available at your local electronics store). Connect one coaxial cable between one
OUT terminal on the splitter and the IN terminal on the converter box. Connect another coaxial
cable between the other OUT terminal on the splitter and the B-IN terminal on an A/B switch
(available at your local electronics store.) Connect a third coaxial cable between the OUT termi-
nal on the converter box and the A-IN terminal on the A/B switch. Finally, connect a coaxial
cable between the OUT terminal on the A/B switch and the antenna terminal on the back of your
TV.
When the A/B switch is in the A position, you need to change channels on the converter box
(and your TV should be tuned to channel 3 or 4); when the A/B switch is in the B position you
can change channels on the TV.
Connecting Other Pieces of Equipment
You may want to connect a VCR, laser disc player, satellite receiver, or another type of equip-
ment to your TV. We recommend that you follow the instructions included with the piece of
equipment you wish to connect.
Safety Note
If you plan on being away from your home for an extended period of time, or if a thunderstorm
is approaching, you should unplug your television, and you may wish to disconnect your TV
from a rooftop or satellite antenna. You do not need to disconnect your TV from a cable system.
ConverterBox
IN
OUT
IN OUT
Converter Box
OUT OUT
IN
OUT
IN IN
B
A

11
Chapter 3: Operating Your TV
Operating Your TV
Once you have connected your TV to an antenna or cable system, plugged the TV in, and put
batteries in the remote, you are ready to use the TV. The first thing you should do is program
your TV so it memorizes all of available channels.
Turning Your TV On
1To turn your TV on, press the POWER button on the remote control.
You can also use the POWER button on the front panel. Make sure
your TV is plugged in before you try to turn it on.
2If your TV set have MAIN POWER button, make sure your TV is
plugged in and you should press MAIN POWER button on the front
panel before you try to turn it on.
Programming Your TV's Channel Memory
Your TV's memory determines the channels that are available using the CH buttons. If a
channel is not in memory, you can tune to it with the number buttons, but not with the CH
buttons. Follow these steps to program your TV's memory:
1With the TV on, press the MENU button twice, then Set-Up menu will appear.
2Use the CH buttons to select Reception , then use the VOL buttons to select
Air or Cable . If you connected an antenna to your TV, select Air ; If you connected a
cable system, select Cable .
3Use the CH buttons to select Memorize Channels , then use the VOL buttons to
enter the Memorize Channels process. Again press the VOL buttons to begin.
4Press the MENU button to return to Set-Up menu.
5Press the MENU button three times to return to normal TV viewing.
Your TV's channel memory will not be affected by a power outage. You will not need to re-pro-
gram the memory unless you change the type of cable or antenna connected to your TV.
Select
Set-Up
Language : English
Reception : Air
Memorize Channels
Add/Delete Channels
Input : TV
Adjust Next
1
Select
Set-Up
Language : English
Reception : Air
Memorize Channels
Add/Delete Channels
Input : TV
Adjust Next
3-1
Select
Set-Up
Language : English
Reception : Air
Memorize Channels
Add/Delete Channels
Input : TV
Adjust Next
2
Memorize Channels
Air 11
Memorizing all air channels.
Please, stand by.
Press MENU to cancel and
return to Set-Up menu.
3-2
5
Select
Set-Up
Language : English
Reception : Air
Memorize Channels
Add/Delete Channels
Input : TV
Adjust Next
4
CHAPTER 3

12
Chapter 3: Operating Your TV
Changing Channels
You can change channels in three ways:
1The CH buttons will take you through all memorized chan-
nels, one by one. The CH buttons will not access channels
that have not been programmed into the TV's memory. For more
information about programming channels into memory, see the
section Programming your TV's Channel Memory on the previ-
ous page.
2The number buttons (0-9) will take you to any channel, even if it
has not been memorized. To change to a channel, enter its num-
ber; the TV will tune to the new channel when you enter the sec-
ond digit of the channel.
3The PREVIOUS button will take you instantly to the last channel
you were watching.
Changing the Volume
1To change the volume of the TV set, use the VOL buttons on
the remote or on the front panel.
2To quickly turn off the sound, press the MUTE button on the
remote. The MUTE will appear on screen, colored green. To
return the volume to its previous level, press MUTE again.
1
2
3
1
2

13
Chapter 3: Operating Your TV
Changing the TV's Channel Memory
Your TV's memory determines the channels that are available using the CH buttons. You
can add channels to this memory or remove them from memory. If a channel is removed from
memory, you can tune to it with the number buttons, but you cannot tune to it with the CH
buttons.
If there are just one channel memorized, then the Add/Delete Channels function will search the
whole channels. But if there are two or more channel memorized, then the Add/Delete Channels
function will search the memorized channels only.
Adding/Deleting a channel to memory
1Use the number buttons to tune to the channel.
2Press the MENU button twice, then Set-Up menu will display.
3Use the CH buttons to select Add/Delete Channels , then use the VOL buttons to
enter the Add/Delete Channels process.
4 If the channel is not in memory, then use the VOL buttons to add the channel from memory.
5 If the channel is in memory, then use the VOL buttons to delete the channel from memory .
6If you are going to delete other channel, then press the CH buttons until desired channel
is selected. And press the VOL buttons to delete the channel.
7Wait 10 seconds, or press the MENU button to return to normal TV viewing.
Displaying the Current Channel
1To quickly see the current channel number and status, press DISPLAY button on
the remote control.
The current channel number and status will be displayed.
11
1
Select
Set-Up
Language : English
Reception : Air
Memorize Channels
Add/Delete Channels
Input : TV
Adjust Next
3
Select
Set-Up
Language : English
Reception : Air
Memorize Channels
Add/Delete Channels
Input : TV
Adjust Next
2
Add/Delete Channels
Air 11
This channel is not in memory.
Press VOL to add.
Press CH for other channels.
Press MENU to return
to Set-Up menu.
4
Add/Delete Channels
Air 11
This channel is in memory.
Press VOL to delete.
Press CH for other channels.
Press MENU to return
to Set-Up menu.
6
Add/Delete Channels
Air 11
This channel is in memory.
Press VOL to delete.
Press CH for other channels.
Press MENU to return
to Set-Up menu.
5

Changing the TV's Input
Normally, your TV displays the signal coming through the antenna terminal. However, If
you ve connected another component to your TV(such as a VCR) using the Video/Audio input,
you will want to be able to view the signal from the component.
To do this, you will need to switch from the TV input to the Line Input, as follows.
1With the TV on, press the MENU button twice, then set-up menu will appear.
2Use the CH buttons to select Input .
3Press the VOL buttons to change from TV to Line .
4Wait 10 seconds, or press the MENU button to return to normal TV viewing.
When it connected an Video/Audio cable from the Video/Audio out jack on the VCR to the
Video/Audio in jack on the front your TV, and your TV s back panel at the same time, the for-
mer takes precedence of the latter.
Select
Set-Up
Language : English
Reception : Air
Memorize Channels
Add/Delete Channels
Input : TV
Adjust Next
1
Select
Set-Up
Language : English
Input : Line
Adjust Next
3
Select
Set-Up
Language : English
Reception : Air
Memorize Channels
Add/Delete Channels
Input : TV
Adjust Next
2
14
Chapter 3: Operating Your TV

15
Chapter 3: Operating Your TV
Adjusting Video Settings
You may wish to adjust the video settings (e. g. contrast or color) to obtain the most pleasing
picture. To do so, follow these directions:
1With the TV on, press the MENU button. then Video menu will appear.
2The Settings item will be selected. Use the VOL buttons to turn Settings to Preset or
Custom.
3Use the CH buttons to select the video setting you wish to adjust.
Descriptions of the video settings are on the next page.
4Use the VOL buttons to adjust the video setting to the level you prefer.
5Use the CH buttons to select another video setting to adjust.
6When you are finished, press the MENU button to return to normal TV viewing.
Select
Video
Settings : Custom
Contrast
Brightness
Sharpness
Color
Tint
Adjust Next
1
100
50
50
50
50
Select
Video
Settings : Preset
Contrast
Brightness
Sharpness
Color
Tint
Adjust Next
3
100
50
50
50
50
Select
Video
Settings : Preset
Contrast
Brightness
Sharpness
Color
Tint
Adjust Next
2
100
50
50
50
50
Contrast
4
100
6
Brightness
5
50

16
Chapter 3: Operating Your TV
Returning to the factory settings
If you would like to return to the original video settings, as they were calibrated at the factory,
follow these steps :
1With the TV on, press the MENU button. then Video menu will appear.
2Press the VOL buttons to set the Settings to Preset .
The TV will remember the Custom settings you had previously chosen. When you set
Settings to Custom again, your previous custom settings will be restored.
Descriptions of video settings
The contrast setting controls the relation between the light and black areas of the screen. If the
light areas are too bright and are losing details, press the VOL button; if the picture is gray
and lacks contrast, press the VOL button.
The brightness settings controls the overall amount of light in the picture. If the picture is too
bright, press the VOL button; if the picture is too dark, press the VOL button.
Sharpness controls how the TV displays edges of objects on-screen. If the TV shows multiple
vertical lines at the edges of an object, press the VOL button; if the vertical edges of
on-screen objects are fuzzy, press the VOL button.
The color setting controls the intensity of color. If the color is over-saturated, press the VOL
button; if the color is washed out, press the VOL button.
The tint setting controls the relationship of red and green in a picture. Tint is especially notice-
able in flesh tones. If flesh tones seem too red or purple, press the VOL button; if flesh tones
are too green, press the VOL button.
Select
Video
Settings : Custom
Contrast
Brightness
Sharpness
Color
Tint
Adjust Next
1
100
50
50
50
50
Select
Video
Settings : Preset
Contrast
Brightness
Sharpness
Color
Tint
Adjust Next
2
100
50
50
50
50

17
Chapter 4: Using Timer Functions
Using Timer Functions
Your TV has a built in-clock, and you can set the TV to turn on and off at times that you select.
You can also set your TV to turn off after counting down a certain amount of time.
Setting the Clock
1With the TV turned on, press the MENU button until Time menu will be displayed.
2The Set Clock item will be selected. Press the VOL buttons to set the clock.
If you hold down either VOL or VOL button, the corresponding numbers will change
more quickly.
3When the clock is set correctly, use the CH buttons to select another Time function,
or press the MENU button to return to normal TV viewing.
Settings the Wake-Up Time
If you enter a time in the Wake-Up time setting, your TV will automatically turn on at that
time. Follow these instructions to set the Wake-Up time .
After Wake-up Timer turned on the TV set, if user do not input the user control (e.g. remote CH
or VOL key) within 2 hours, the TV set will turn off automatically. If user input the user control
within 2 hours, the TV set will turn on continuously.
It is safety feature for prevent from any kind of problem without human control.
1With the TV turned on, press the MENU button until Time menu will be displayed.
2Use the CH buttons to select Wake-Up time item.
3If you hold down either VOL or VOL button, the corresponding numbers will change
more quickly.
4When the setting is correct, use the CH buttons to select another Time function, or
press the MENU button to return to normal TV viewing.
CHAPTER 4
Select
Time
Set Clock : :
Wake-Up time : :
Off time : :
Sleep Timer : 00 min
Adjust Next
1
Select
Time
Set Clock : 12 : 00 AM
Wake-Up time : :
Off time : :
Sleep Timer : 00 min
Adjust Next
3
Select
Time
Set Clock : 12 : 00 AM
Wake-Up time : :
Off time : :
Sleep Timer : 00 min
Adjust Next
2
Select
Time
Set Clock : 12 : 00 AM
Wake-Up time : :
Off time : :
Sleep Timer : 00 min
Adjust Next
1
Select
Time
Set Clock : 1 2 : 00 AM
Wake-Up time : 06 : 30 AM
Off time : :
Sleep Timer : 00 min
Adjust Next
3
Select
Time
Set Clock : 12 : 00 AM
Wake-Up time : :
Off time : :
Sleep Timer : 00 min
Adjust Next
2

18
Chapter 4: Using Timer Functions
Setting the Off Time
If you enter a time in the Off time setting, your TV will automatically turn off at that time.
Follow these instructions to set the Off time .
1With the TV turned on, press the MENU button until Time menu will be displayed.
2Use the CH buttons to select Off time item.
3If you hold down either VOL or VOL button, the corresponding numbers will change
more quickly.
4When the setting is correct, use the CH buttons to select another Time function, or
press the MENU button to return to normal TV viewing.
Canceling the Wake-Up Time or Off Time
If you would like to cancel the Wake-up Time or the Off Time, Press the VOL buttons until
the time settings return to - -:- - .
The Wake-Up Time and Off Time will not function correctly unless the clock has been set.
Select
Time
Set Clock : 12 : 00 AM
Wake-Up time : 06 : 30 AM
Off time : :
Sleep Timer : 00 min
Adjust Next
1
Select
Time
Set Clock : 1 2 : 00 AM
Wake-Up time : 06 : 30 AM
Off time : 1 1 : 30 PM
Sleep Timer : 00 min
Adjust Next
3
Select
Time
Set Clock : 1 2 : 00 AM
Wake-Up time : 06 : 30 AM
Off time : :
Sleep Timer : 00 min
Adjust Next
2