Daewoo DTQ 25G1 User manual

Color Television
INSTRUCTION MANUAL
DTQ 25G1
DTQ 29G1

CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral triangle, is
intended to alert the user to the presence of uninsulated “dangerous voltage” with-
in the product’s enclosure that may be of sufficient magnitude to constitute a risk
electric shock.
The exclamation point within an equilateral triangle is intended to alert the user to
the presence of important operating and servicing instructions in the literature
accompanying the appliance.
WARNING
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN
OR MOISTURE.
CAUTION
CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE MANUFAC-
TURER COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT.
NOTE TO CATV SYSTEM INSTALLER
THIS REMINDER IS PROVIDED TO CALL THE CATV SYSTEM INSTALLER'S ATTEN-
TION TO ARTICLE 820-40 OF THE NEC THAT PROVIDES GUIDELINES FOR PROPER
GROUNDING AND, IN PARTICULAR, SPECIFIES THAT THE CABLE GROUND SHALL
BE CONNECTED TO THE GROUNDING SYSTEM OF THE BUILDING, AS CLOSE TO
THE POINT OF CABLE ENTRY AS PRACTICAL.
CAUTION
To provide power to the TV, insert the AC plug into a standard 220V 50/60Hz outlet.
NOTE
If you feel a static discharge when touching the unit, and the unit does not function, simply unplug
the unit from the outlet. When you plug the unit back in, it should work normally.
Do not install power cords near any heating element or cooking appliances.

1
CONTENTS
Table of Contents
Chapter 1: Connecting an Antenna/Cable and VCR to your TV 3
Connecting an Antenna 3
Antennas with two sets of leads 4
Connecting a Cable System 4
Connecting a VCR 6
Connecting Other pieces of Equipment 6
Safety note 6
Chapter 2 : Overview of Your Equipment 7
Your TV’s Front view 7
Your TV’s Back view 7
Your remote control 8
Installing your remote control batteries 10
Notes 10
Chapter 3 : Operating Your TV 11
Turning your TV ON/OFF 11
Changing channels 11
Changing volume 11
Understanding on-screen menu 12
Selecting the input source 13
Using the direct button on the remote control. 13
Using on-screen Menu 13
Programming your TV’s channel memory 14
Source selection 14
Auto programming function 14
Adding and Erasing channels 15
Adjusting the picture 16
Custom mode 16
Preset mode 17
Adjusting the sound 18
Selecting Stereo/SAP broadcasts 18
About AVC 18
About Loudness 18
Convenient Remote Function 20
Display on-screen information 20
Muting the sound 20
Table of Contents

2
Chapter 4 : Using the Advanced Features 21
Changing on-screen Display language 21
Using closed-captioned Function 22
Captioning 22
Viewing caption 22
Programming your Favorite channels 24
Programming your favorite channels 24
Selecting your favorite channels 24
Setting the Timer 25
Setting the Clock 25
Setting the on-timer 25
Setting the off-timer 25
Setting the sleep timer 26
Using the power restore feature 27
Chapter 5 : Using the Special Features 28
Watching Picture-In-Picture (PIP Function) 28
Display the PIP image 28
Changing the PIP channels 28
To change the position of the small picture 28
To Display a picture from an external source as a small picture 28
To switch the main and small picture 29
To freeze the small picture is displayed 29
Changing the PIP image size 29
Using channel label feature 30
Programming the channel labels 30
Clearing channel labels 31
Watching Auto demo feature 32
Starting the on-screen demonstration 32
To stop the demonstration 32
Chapter 6 : Troubleshooting 33
Warranty 34
Table of Contents

3
CHAPTER 1
Your TV will provide you with the best performance if you connect it to an external anten-
na or cable system. Follow the directions below to make this connection. Please note that
you will normally only have to make one of the connections shown below, not all of them.
All connections will be made to the antenna terminal on the back of your TV. The antenna
terminal is a silver metal post partially surrounded by two plastic tabs. For help in locating
the antenna terminal, see “Your TV’s Back View” on page 7.
Connecting an Antenna If your antenna ends in a single coaxial lead,
simply press or screw the cable onto the antenna
terminal on the back of your TV.
If your antenna ends in a pair of 300 ohm twin leads, you must use a 300-ohm/75-ohm
adapter. Place the leads underneath the screws on the adapter, tighten the screws, then press
the adapter onto the antenna terminal on the back of the TV.
Chapter 1 : Connecting an Antenna/Cable and VCR to Your TV
Connecting an Antenna/Cable and VCR to Your TV
,
,
,
,
,,
,,
,,

4
Antennas with two sets of leads
You might have two sets of leads from your antenna system, especially if you have one
antenna for VHF signals and one antenna for UHF signals.
If your antenna system has both a coaxial lead and twin 300-ohm leads, you must
obtain a combiner (available at your local electronics store). Press or screw the coaxial lead
onto the combiner; place the twin leads underneath the screws on the combiner and tighten
the screws. Press the cable from combiner onto the antenna terminal on the back of your
TV.
If your antenna system has two sets of twin 300-ohm leads, you must obtain a combiner
(available at your local electronics store). Place one set of twin leads underneath the screws
on the combiner and tighten the screws. Do the same with the other set of twin leads. Press
the cable from the combiner onto antenna terminal on the back of your TV.
Connecting a cable system
If your cable set-up is not described below, please contact your cable company for more
information.
If your cable system does not require the use of
a cable box, simply press or screw the incoming
cable onto the antenna terminal on the back your
TV.
Chapter 1 : Connecting an Antenna/Cable and VCR to Your TV
,
,
,
,
,
,
,,
,,
,,
,,

5
If your cable system requires you to use a converter box for all channels, connect the
incoming cable to the IN terminal on the converter box. Connect another cable between the
OUT terminal on the converter box and the antenna terminal on the TV. You will need to
keep your TV tuned to channel 3 or 4 and change channels using the converter box.
If your cable system only requires you to use a converter box for some channels (i. e.
pay-TV channels), follow these steps: Find the primary incoming coaxial cable. Plug this
cable into a splitter (available at your local electronics store). Connect one coaxial cable
between one OUT terminal on the splitter and the IN terminal on the converter box.
Connect another coaxial cable between the other OUT terminal on the splitter and the B-IN
terminal on an A/B switch (available at your local electronics store.) Connect a third coaxial
cable between the OUT terminal on the converter box and the A-IN terminal on the A/B
switch. Finally, connect a coaxial cable between the OUT terminal on the A/B switch and
the antenna terminal on the back of your TV.
When the A/B switch is in the A position, you need to change channels on the converter
box (and your TV should be tuned to channel 3 or 4); when the A/B switch is in the B posi-
tion you can change channels on the TV.
Chapter 1 : Connecting an Antenna/Cable and VCR to Your TV
,,
,,
,,
,,

6
Connecting a VCR
Connecting VIDEO 1 IN(rear panel) or VIDEO 2 IN(front panel) jacks on the TV panel to
the video/audio output jacks of an installed VCR, Laser disk player, video camera, etc. for
playback of video material.
Connecting Other Pieces of Equipment
You may want to connect a VCR, laser disc player, satellite receiver, or another type of
equipment to your TV. We recommend that you follow the instructions included with the
piece of equipment you wish to connect.
Safety Note
If you plan on being away from your home for an extended period of time, or if a thunder-
storm is approaching, you should unplug your television, and you may wish to disconnect
your TV from a rooftop or satellite antenna. You do not need to disconnect your TV from a
cable system.
Chapter 1 : Connecting an Antenna/Cable and VCR to Your TV
Connecting Stereo VCR Connecting Mono VCR
Connecting Video camera or Game machine Connecting an Audio Amplifier

7
Chapter 2 : Overview of your equipment
CHAPTER 2
Your TV comes with a remote control. The section below summarizes the buttons, controls,
and terminals that you will use with your TV.
Overview of your equipment
Menu
Volume Up
Volume down
Channel Up
Channel down
POWER
Video
L(Mono)
R
Earphone
ANT
TVIDEO1 IN MONITOR OUT
VIDEO AUDIO
L(mono) R VIDEO AUDIO
L R
Your TV’s Front View
Your TV’s Back View

8
1 POWER
Use this button to turn your TV on
or off.
2 MUTE
Use to turn the TV’s sound on and
off.
3 PIP ON/OFF
Use this button to turn PIP on/off.
4 PIP POSITION
Use this button to move PIP display
position.
5 PIP SOURCE
Use this button to select PIP source.
6 PIP SWAP
Use this button to exchange PIP
source and main source.
7 PIP STILL
Use this button to still PIP source.
8 0-9
Use these buttons to select
channels.
9 SLEEP
Use this button to program the TV
to turn off after a certain time.
10 RECALL
-Use this button to display the
channel number, channel label and
stereo status.
-Use this button repeatedly to select
the main menu or sub menu.
(Changing the channel)
11 TV/VIDEO
Use this button to select main
picture source.
Chapter 2 : Overview of your equipment
Your remote control
POWER
123
456
78
0
9
SLEEP RECALL
MUTE
PIP
ON/OFF
POSITION
SOURCE
SWAP
STILL
TV/VIDEO FAVORITE CH
CAPTION
CH
CH
REMOTE CONTROLLER R-35H13
MENUVOL VOL
MTS
1
3
4
5
6
7
17
2
8
10
9
12
11
14
13
15
16