Daheng Imaging MARS User manual

MARS QuickGuideMARS QuickGuide
Thank you for choosing DAHENG IMAGING products! This guide will help you get started as quickly as
possible with our products. For more information(e.g. detailed manuals, CAD/3D drawings, driver software,
etc.), please visit: www.daheng-imaging.com/en
This guide applies to the following products:
MARS
■■GigE Series MARS-G-P
■■5GigE Series MARS-5G-P
■■USB3.0 Series MARS-U3
Please visit our website www.daheng-imaging.com/en and download the latest driver and software from
[Downloads] →[Software Downloads].
After uncompressing the download file, please run the setup program(.exe file). You can choose the
components which you need during the installation process.
If you have any problems during the installation, please contact our technical support engineer for more
detailed instructions: isuppor[email protected].
■ Download
■ Installation
I. Download and Installation (Driver/Software)
II. Power
The power provided must adhere to the requirements specied
in IEEE 802.3af.
Camera can get power from the Hirose 12-pin receptacle
via a standard I/O cable.Nominal operating voltage is
+12V~+24VDC (± 10%).
Voltage outside of the specied range or use of connectors that do not match the IO port may cause camera damage.
China Daheng Group, Inc. Beijing Image Vision
Technology Branch
Website: www.daheng-imaging.com/en
Sales Email: [email protected]
Sales Tel: [phone]
Support Email: isuppor[email protected]
When you supply power to the camera both via the camera’s RJ45 jack and via the 12-pin Hirose I/O port, the
camera will get power via the Hirose I/O port. And if you cut off the Hirose I/O port, the camera will get power via PoE and
may restart.
• Via PoE
• Via external DC power supply
■GigE Interface Camera
■ USB3.0 Interface Camera
Power supply through USB3.0 interface: 5VDC
MARS-G-P
MARS-G-P
MARS-U3
MARS-G5-P
MARS-G5-P

III. I/O Port
IV. Running the Acquisition Program
After the camera is connected properly, the LED on the back panel
of the camera shows green continuous, it indicates that the camera
has been ready for acquiring images or other operations.
Run the Demo (demonstration program). You can open the demo by the following ways: “Desktop\
Daheng Galaxy Viewer” or “Start\ All Programs\Daheng Galaxy Devices\Daheng Galaxy Viewer”
In the Demo, you can adjust the cameras' parameters, acquire and save images.
If the camera is rst used, Please run the GigE IP Congurator tool by the following ways: “Desktop\
GigE IP Congurator” or “Start\All Programs\Daheng Galaxy Devices\GigE IP Congurator”
The camera's IP address, conguration modes, and the user-dened name of the cameras can be modied
in the software.
■IP Conguration
■Connecting the camera
■ Running the Acquisition program
Pin Denition Color Description
1 Line0+ Green Opto-isolated input +
2 GND Blue PWR GND & GPIO GND
3 Line0- Gray Opto-isolated input -
4 POWER_IN Purple
Camera external power,
+12V DC~+24V DC
(USB3.0 interface camera does not connect pin4)
5 Line2 Orange GPIO input/output
6 Line3 Pink GPIO input/output
7 Line1- White green Opto-isolated output -
8 Line1+ White blue Opto-isolated output +
9 NC1 White gray Not Connected, reserved
10 GND White purple PWR GND & GPIO GND
11 NC2 White orange Not Connected, reserved
12 NC3 White pink Not Connected, reserved
(USB3.0 interface camera does not require IP conguration)
The polarity of power and GPIO cannot be reversed, otherwise, camera or other peripherals could burn out.

■The screw and camera have a screw length between 3 and 4.8 mm
■Screw assembly torque ≤5N.M. If the screw assembly torque is too large, it may cause the camera thread
stripping
■Housing temperature during operation: 0°C ~ 45°C, humidity during operation: 10% ~ 80%
■Storage temperature: -20°C ~ 70°C
■To avoid collecting dust in the optical lter, always keep the plastic cap on cameras when no lens is
mounted
■PC requirement for MARS-G-P and MARS-U3 series camera: Intel Core 2 Duo, 2.4GHz or above, and 2GB
memory or above
■PC requirement for MARS-G5-P series camera: Intel Core i5 or above, 8GB memory or above, Win7 64bit
OS or above
■NIC requirement for MARS-G-P series camera: Intel Pro 1000 NIC or higher performance Gigabit LAN
conrming to IEEE802.3af standard, CAT-5e or CAT-6 cables, less than 100m, Gigabit Switch conrming to
IEEE802.3af standard
■NIC requirement for MARS-G5-P series camera: 5GigE NIC conrming to IEEE802.3af standard or higher
performance 10GigE NIC with 5Gbps link speed, CAT-5e cables or above, length less than 100m, switch
conrming to IEEE802.3af standard
■USB3.0 host controller requirement for MARS-U3 series camera: Intel controller integrated in mainboard is
recommend. Select Renesas controller if external frame grabber is needed
■ The cable must have a locking screw at the end of the device for USB3.0 interface cameras
■Make sure that cameras are transported in the original factory packages
■CAT-5e cables or above with S/STP shielding are recommended for GigE interface cameras
■USB cables certicated by USB IF with lock screw are recommended for USB3.0 interface cameras
■Using shielded cable can avoid electro-magnetic interface. Shielding layer of the cable should conduct to
ground nearby and not until stretched too long. When many devices need conduct to ground, using single
point grounding to avoid earth loop
■Try to use camera cables that are the correct length. Avoid coiling camera cables. If the cables are too
long, use a meandering path rather than coiling the cables
■Keep your cameras away from equipment with high voltage, or high current (as motor, inverter, relay, etc.).
If necessary, use additional shielding
■ESD (electro-static discharge) may damage cameras permanently, so use suitable clothing (cotton) and
shoes, and touch the metal to discharge the electro-static before operating cameras
V1.0.0 | 2021.05
Guidelines for Avoiding EMI and ESD
Environmental Requirements
Camera Mechanical Installation Precautions
V. Precautions