Dahua technology Bc581e82 User manual

UNPACKING

Your system includes the following:

BC581E82

Eight-channel HDCVI Recording Kit

❶

Cameras

• 8 x HDCVI Dome Cameras

• 8 x Hardware Packs, with:

Moun ng Template,

Expansion Bolts (3),

Self-tapping Screws (3), Hex Wrench,

Startup Guide, and So ware CD

HDCVI DVR

• 1 x 8-channel HDCVI DVR, with:

Pre-installed 2 TB HDD,

12 VDC Power Supply,

Ethernet Cable, Mouse,

Hard Drive SATA Cable, HD Hardware,

Startup Guide, and So ware CD

CONNECTIONS

Camera Connec ons

❷

1 Video Output HDCVI, CVBS, AHD, TVI

2 Power Input 12 VDC

CONNECTIONS

HDCVI DVR Connec ons

1 Audio IN (x4) 7 USB Port

2 Analog Video IN (x8) 8 12 VDC Power IN

3 Audio OUT 9 Alarm I/O

4 HDMI OUT 10 Audio IN (x4)

5 RJ-45 11 VGA OUT

6 RS485 A/B 12 On/Oﬀ Bu on

❸

DIMENSIONS

Camera and HDCVI DVR

• Ensure the wall or ceiling can support 3x the weight of the

camera.

• Do not connect the camera to the power supply during

installa on.

• For outdoor installa ons, ensure the connec on between

the network cable and the camera jack is housed within a

wall or indoors or use the waterproof cable connector.

❹INSTALLATION

Mount and Make Connec ons

❺INSTALLATION

Posi oning the Camera

• Loosen, but do not remove the set screws on either side of

the bracket that holds the camera.

• Tilt the camera to adjust the  lt angle (0° to +65°). Tighten

the two locking screws on the bracket to lock the  lt angle.

• Turn the camera module to adjust image pan orienta on

(0° to +355°).

• Turn the camera base to adjust the rota on of the camera

(0° to +355°).

❻

INSTALLATION

Place the HDCVI DVR

BC581E82

Eight-channel HDCVI Recording Kit

❼INSTALLATION

Connect Peripherals

❽

• Connect the mouse to the USB port on the rear panel.

• Connect a VGA or HDMI cable to the rear panel and to the

display monitor.

INSTALLATION

Connect Cameras

❾

OPERATION

❿OPERATION

Set Parameters in Startup Wizard

⓫OPERATION

View Live Video

⓬

• Ground the unit using the ground connec on of the power

supply to protect the unit from damage, especially in damp

environments.

• Protect the plug and power cord from foot traﬃ c, being

pinched, and its exit from the unit.

• Do not place the unit in a wet, dusty, extremely hot or an

extremely cold environment; and avoid environments with

strong electromagne c radia on.

• Follow the prompts in the Startup Wizard to set the follow-

ing:

General Device ID and opera on, Date/Time, Holiday

Schedule

Encode Video and audio se ngs for each channel

Schedule Recording schedule conﬁ gura on

Record Main stream and sub stream se ngs

• Set the Username and Password a er ini al start-up.

• Supply the default password (“admin”) for the Admin

user.

• Supply a new password.

• Supply answers for two conﬁ rma on ques ons in case the

password has to be reset.

• A er Admin Security is set, supply the Username and the

new Password.

• Connect the incoming coaxial cable from each HDCVI dome

camera to a BNC connector on the rear panel.

• Connect the DVR to the 12 VDC power supply and turn on

the device using the On/Oﬀ bu on.

Rev. 001.005. Copyright © 2017 Dahua Technology. All rights reserved. Information contained in this document is subject to change without prior notice. Dahua does its best to provide accurate information, but cannot be held responsible for typos or mistakes.

• Click Live in the Main Menu.

• Change the Live screen grid if more camera channels are

desired.