Dahua ITC237-PW1A-IRZ User manual

i
ITC237-PW1A-IRZ
Web Operation Manual
Version 1.0.0

ii
Important Safeguards and Warnings
1．Electrical safety
All installation and operation here should conform to your local electrical safety codes.
The power shall conform to the requirement in the SELV (Safety Extra Low Voltage) and the Limited
power source is rated 90-240V.
We assume no liability or responsibility for all the fires or electrical shock caused by improper handling
or installation.
2．Transportation security
Heavy stress, violent vibration or water splash are not allowed during transportation, storage and
installation.
Please keep package material well in case you need to send it back to your local retailer or
manufacturer for maintenance work.
Non-original package material may result in device damage during the transportation.
3．Installation
Do not apply power to the camera before completing installation.
Please install the proper power cut-off device during the installation connection in case there is any
emergency situation.
Always follow the instruction guide the manufacturer recommended.
4．Qualified engineers needed
All the examination and repair work should be done by the qualified service engineers.
We are not liable for any problems caused by unauthorized modifications or attempted repair.
5．Environment
This series camera should be installed in a cool, dry place away from direct sunlight or strong light,
inflammable, explosive substances and etc.
The working temperature ranges from -30℃~ to +60℃. Please keep it away from the electromagnetic
radiation object and environment.
Please keep the sound ventilation.
Do not allow the water and other liquid falling into the camera.
Usually we recommend thunder-proof device to prevent thunder strike.

iii
The GND port of the product shall be grounded to further enhance the reliability of the device.
6. Accessories
Be sure to use all the accessories recommended by manufacturer.
Before installation, please open the package and check all the components are included.
Contact your local retailer ASAP if something is broken in your package.
7. Daily Maintenance
Please shut down the device and then unplug the power cable before you begin daily maintenance work.
Use the dry soft cloth to clean the device.
If there is too much dust, please use the water to dilute the mild detergent first and then use it to clean
the device. Finally use the dry cloth to clean the device.

iv
Table of Contents
1Live................................................................................................................................ 1
1.1 Log in................................................................................................................ 1
1.2 Video Bit Stream Bar ........................................................................................ 4
1.3 Preview Window Switch.................................................................................... 4
1.4 System Menu.................................................................................................... 5
1.5 Common Function Bar...................................................................................... 6
1.6 Monitor Window Switch..................................................................................... 6
2Query............................................................................................................................. 8
2.1 Picture Query.................................................................................................... 8
2.2 Record Query.................................................................................................... 8
2.2.1 Record........................................................................................................ 8
2.2.2 Water Mark................................................................................................. 9
3Configure..................................................................................................................... 10
3.1 ITC.................................................................................................................. 10
3.1.1 Lane Property........................................................................................... 10
3.1.2 Snapshot .................................................................................................. 11
3.1.3 Intelligence Default................................................................................... 12
3.1.4 Intelligence Default................................................................................... 17
3.1.5 Snap Cutout.............................................................................................. 17
3.1.6 White List.................................................................................................. 18
3.2 Camera........................................................................................................... 20
3.2.1 Attribute.................................................................................................... 21
3.2.2 Video ........................................................................................................ 23
3.3 Network........................................................................................................... 28
3.3.1 TCP/IP...................................................................................................... 28
3.3.2 IP Filter..................................................................................................... 29
3.4 Event............................................................................................................... 29
3.4.1 Relay-out.................................................................................................. 29
3.4.2 Abnormity ................................................................................................. 30
3.5 Storage........................................................................................................... 31
3.6 System............................................................................................................ 31
3.6.1 General..................................................................................................... 31
3.6.2 Account..................................................................................................... 33
3.6.3 Default...................................................................................................... 38
3.6.4 Import/Export............................................................................................ 38
3.6.5 Auto Maintain............................................................................................ 39
3.6.6 Upgrade.................................................................................................... 40

v
3.7 Information...................................................................................................... 40
3.7.1 Version ..................................................................................................... 40
3.7.2 Log............................................................................................................ 41
3.7.3 Online User............................................................................................... 42
4Logout......................................................................................................................... 43

1
1 Live
1.1 Log in
Open IE and input HD intelligent traffic camera IP address in the address column. For example, if your
IP is 192.168.1.108, then please input http:// 192.168.1.108 in IE address column. See Figure 1-1
Figure 1-1 IE
System pops up warning information to ask you whether install webrec.cab control or not. Please click
yes button.
If you can’t download the ActiveX file, please modify your settings as follows. See Figure 1-2.
Input your IP
address here.

2
Figure 1-2 Security Settings
After installation, the interface is shown as below. See Figure 1-3.
Please input your user name and password.
Default factory name is admin and password is admin.
Note: For security reasons, please modify your password after you first login.

3
Figure 1-3 Login Interface
After you logged in, HD intelligent traffic camera web main interface is shown as in Figure 1-4.
Figure 1-4 Web Main Interface

4
There are five sections:
Section 1: Video bit stream bar
Section 2: Preview window switch
Section 3: System menu
Section 4: Common function bar
Section 5: Monitor window switch
1.2 Video Bit Stream Bar
T he video bit stream bar interface is shown as in Figure 1-5.
Figure 1-5 Video Bit Stream Bar
Please refer to the following sheet for detailed information.
Parameter
Function
Main stream
You can use main stream to record video record, network
monitor function under normal network environment. You can set
resolution within its supported range.
Extra stream
It is a substitute for main stream under insufficient band width.
Protocol
Select video monitoring protocol, currently support TCP only.
1.3 Preview Window Switch
The preview window switch interface is shown as in Figure 1-6.
Figure 1-6 Preview Window Switch
---- Aspect ratio, adjust image to original size or best fit.
----Window switch to large window and display adjusting window. See Figure 2-8.
is full screen button. Te exit full screen, double click or press Esc.

5
Figure 1-7 Adjusting Window
Note:
All the operations here apply to WEB end only.
Please go to “Setup->Camera->Attributes” to set.
Please refer to the following sheet for detailed information.
Parameter
Function
Video
setup
It is to adjust monitor video brightness.
It is to adjust monitor video contrast.
It is to adjust monitor video hue.
It is to adjust monitor video saturation.
Reset
Reset brightness, contrast, hue and saturation to system default
values.
1.4 System Menu
System menu is shown as in Figure 1-8.
Please refer to chapter 1 Live, chapter 2 Query, chapter 3 Setup, chapter 4 Logout for detailed
information.
Figure 1-8 System Menu

6
1.5 Common Function Bar
The common function bar interface is shown as in Figure 1-9.
Figure 1-9 Common Function Bar
Please refer to the following sheet for detailed information.
Parameter
Function
Record Type
Select record type, default is dav.
Receive
pictures
Check it to automatically receive pictures via snapshot, coil detect and video
detect. Record plate, vehicle color, speed and other info and display them in
window.
Manual
snapshot
Click on the button to snapshot. Snapshots are saved based on setup in “Setup-
>Camera->Video->Path”.
Zoom in
Click on the button to zoom in with left mouse. Right click to exit.
Snapshot
Click on the button to snapshot current picture and save it.
Record
Click on the button to record. Record file is saved based on setup in “Setup-
>Camera->Video->Path”. Please refer to Chapter 4.2.2.5.
Easy Focus
Click Easy Focus to auto focus, or you can manually zoom in and focus.
Zoom: Manually focus, zoom in/out.
Focus: Manually focus make image clear.
1.6 Monitor Window Switch
The monitor window switch interface is shown as in Figure 1-10.
Figure 1-10 Monitor Window Switch
----Display in single window.
---- Display in four windows.

7
---- Display in full screen.

8
2 Query
2.1 Picture Query
Click query button, you can see an interface is shown as in Figure 2-1.
Click Open Local, select picture you want to verify and click Water Verify, then you can view the result.
Select the picture, click Open to preview.
Figure 2-1 Picture Query
2.2 Record Query
2.2.1 Record
Click record query, you can see an interface is shown as in Figure 2-2.

9
Figure 2-2 Record Query
2.2.2 Water Mark
Note:
Before user can use this function, he/she must enable water mark in Setup>Camera>Video, and set
watermark content. Default watermark is :DigitalCCTV.
Select record file, click Water Mark, system shows progress of verifying and normal watermark. See
Figure 2-3.
Figure 2-3
When it is complete, the page will show complete.

10
3 Configure
3.1 ITC
3.1.1 Lane Property
User shall set related parameter according to their need.
The lane property interface is shown as in Figure 3-1.
Figure 3-1 Lane Property
Please refer to the following sheet for detailed information.
Parameter
Function
Snap enable
Select lane to enable. The no. corresponds to actual lane no.
Working road
Select road type.
Lane
Select lane to snapshot.
Customized lane no.
Set different no. for each lane.
Direction
Select lane direction to snapshot.
Left lane line type
Solid white line by default.
Right lane line type
Solid white line by default.
Direction
Set vehicle direction.

11
Parameter
Function
ANPR
Set whether to snapshot vehicle at ANPR or not.
Click on button in Illegeal Type Config, you will see advance config interface in Figure
3-2.
Figure 3-2 Advance Config
Parameter
Function
Snap
Amount
Set number of snapshot.
Snap
Direction
Check Observe to snapshot vehicle driving in correct direction only.
Check Reserve to snapshot vehicle driving in retrorse direction only.
Check DoubleDirection to snapshot vehicles in both directions at the
same time.
3.1.2 Snapshot
The snapshot interface is shown as in Figure 3-3.

12
Figure 3-3 Snapshot
Please refer to the following sheet for detailed information.
Parameter
Function
General setup
Select auto or manual mode. Manual mode includes video trigger and coil
trigger.
Work mode
Select frame interval or custom interval.
Max speed
Set max speed supported by device.
OSD select
Set OSD menu.
General info
Select OSD info displayed on picture border.
Address
Set device installation address, and this OSD will be displayed on picture
border.
Extend info
Select OSD info to be displayed on picture border.
Font
Set OSD info font size, color.
Refresh
Click on refresh to receive the latest device parameters.
3.1.3 Intelligence Default
3.1.3.1 RS485/IO
The intelligence default interface is shown as in Figure 3-4.

13
Figure 3-4 RS485/IO
Please refer to the following sheet for detailed information.
Parameter
Note
Start Coil IO
Select Start Coil IO enable option, to enable coil IO, may config
trigger mode and IO.
IO
Select coil IO.
Coil X
Set each coil’s trigger mode.
Operation Mode
Support ANPR mode.
Scheme
Include several typical combination of coil snapshot.
ANOR mode：
Double_in2_nospeed：dual coils, when vehicle head enters
the 2nd coil, snapshot
Single_in1_nospeed：single coil, when vehicle head or tail
enters the coil, snapshot
Current Lane No.
Select different lanes to set corresponding coil parameters.
Distance Between
Coil1&Coil2
Actual distance from centers of coil 1 to coil 2.
Note:
This value must match actual value, other speed measurement
will not be accurate.
Coil Width
According to actual condition, set coil width.
Apply to
Apply config scheme of current channel to other channels.
3.1.3.2 Video Analysis
The video analysis interface is shown as in Figure 3-5.

14
Figure 3-5 Video Analysis
Please refer to the following sheet for log parameter information.
Parameter
Function
Virtual lane
Select virtual lane no.
Physical lane
Set physical lane no. according to actual condition.
Region
Set detect region.
Select and click on redraw to drawn region.
Lane line
Draw lane according to actual condition.
Each lane requires two lines.
Arrow of lane represents moving direction.
Select and click on redraw to drawn region.
You can only draw in up/down direction.
Detect
Draw border line to trigger snapshot which is similar to actual coil. When
vehicle reach this line, snapshot will be triggered.
Detect line is available inside drawn region only.
Select and click on redraw to drawn region.
Vehicle
head/vehicle rear
When you select front, lane arrow is downward. When you select rear, lane
arrow is upward. These are vehicle moving direction with different
representations.
The speed measuring interface is shown as in Figure 3-6.

15
Figure 3-6 Video Analysis
Please refer to the following sheet for log parameter information.
Parameter
Function
H
This is camera height from the ground. Note: This value must match actual
value; otherwise speed measure will be inaccurate.
L1
This is distance from camera to scene bottom.
Note: This value must match actual value; otherwise speed measure will be
inaccurate.
L2
This is distance from camera to scene median (yellow line).
Note: This value must match actual value; otherwise speed measure will be
inaccurate.
The recognition interface is shown as in Figure 3-7.