Dahua DH-HAC-HDW1200EM-A User manual

HDCVI
Eyeball Camera Lite
User’s Manual
V1.0.0
Questo manuale d’istruzione è fornito da trovaprezzi.it. Scopri tutte le offerte per Dahua DH-HAC-
HDW1200EM-A o cerca il tuo prodotto tra le migliori offerte di Videosorveglianza

Foreword I
1 Foreword
General
This user’s manual (hereinafter referred to be "the Manual") introduces the functions, installation, and
operations of the camera.
Safety Instructions
The following categorized signal words with defined meaning might appear in the Manual.
Signal Words
Meaning
Indicates a medium or low potential hazard which, if not avoided,
could result in slight or moderate injury.
Indicates a potential risk which, if not avoided, could result in
property damage, data loss, lower performance, or unpredictable
result.
Provides methods to help you solve a problem or save you time.
Provides additional information as the emphasis and supplement
to the text.
Revision History
No.
Version
Revision Content
Release Time
1
V1.0.0
First Release.
June 8, 2018
Privacy Protection Notice
As the device user or data controller, you might collect personal data of others' such as face,
fingerprints, car plate number, Email address, phone number, GPS and so on. You need to be
in compliance with the local privacy protection laws and regulations to protect the legitimate
rights and interests of other people by implementing measures include but not limited to:
providing clear and visible identification to inform data subject the existence of surveillance
area and providing related contact.
About the Manual
The Manual is for reference only. If there is inconsistency between the Manual and the
actual product, the actual product shall prevail.
We are not liable for any loss caused by the operations that do not comply with the Manual.
The Manual would be updated according to the latest laws and regulations of related
regions. For detailed information, see the paper Manual, CD-ROM, QR code or our official
website. If there is inconsistency between paper User's Manual and the electronic version,
the electronic version shall prevail.

Foreword II
All the designs and software are subject to change without prior written notice. The product
updates might cause some differences between the actual product and the Manual. Please
contact the customer service for the latest program and supplementary documentation.
There still might be deviation in technical data, functions and operations description, or
errors in print. If there is any doubt or dispute, please refer to our final explanation.
Upgrade the reader software or try other mainstream reader software if the Guide (in PDF
format) cannot be opened.
All trademarks, registered trademarks and the company names in the Manual are the
properties of their respective owners.
Please visit our website, contact the supplier or customer service if there is any problem
occurred when using the device.
If there is any uncertainty or controversy, please refer to our final explanation.

Important Safeguards and Warnings III
Important Safeguards and Warnings
Electrical Safety
All installation and operation should conform to your local electrical safety codes.
The power source shall conform to the requirement of the Safety Extra Low Voltage (SELV)
standard, and supply power with rated voltage which conforms to Limited power Source
requirement according to IEC60950-1. Please note that the power supply requirement is
subject to the device label.
A readily accessible disconnect device shall be incorporated in the building installation
wiring.
Make sure if the camera power adapter meets the camera operating voltage requirement
before powering up the device (The material and length of the power cable might influence
the device voltage).
Prevent the power cable from being trampled or pressed, especially the plug, power socket
and the junction extruded from the device.
We assume no liability or responsibility for all the fires or electrical shock caused by
improper handling or installation.
Environment
Do not aim the device at strong light to focus, such as lamp light and sun light.
Transport, use and store the device within the range of allowed humidity and temperature.
Keep the camera away from water or other liquid to avoid damages to the internal
components.
Keep sound ventilation to avoid heat accumulation.
Heavy stress, violent vibration or water splash are not allowed during transportation,
storage and installation.
Pack the device with standard factory packaging or the equivalent material when
transporting the device.
It is recommended to use the device together with lightning arrester to improve lightning
protection effect.
It is recommended to ground the device to enhance reliability.
It is recommended to use qualified video transmission cable to improve video quality. It is
recommended to use RG59 coaxial cable or higher standard.
Use standard components or accessories provided by manufacturer and make sure the
device is installed and maintained by professional engineers.

Important Safeguards and Warnings IV
The surface of the image sensor should not be exposed to laser beam radiation in an
environment where a laser beam device is used.
Do not provide two or more power supply sources for the device; otherwise it might
damage the device.
When the camera is in the condition of PoC power supply, do not connect any other device
between the camera and PoC transceiver including UTC, Balun, optical transceiver,
distributor and convertor and so on; otherwise, the device might get burned.
PoC supply voltage is up to 52V. Do not dismantle the device during normal operation;
otherwise it might cause danger to both device and users due to high voltage.

Regulatory Information V
Regulatory Information
FCC Information
Changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.
FCC conditions:
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions:
This device may not cause harmful interference.
This device must accept any interference received, including interference that may cause
undesired operation.
FCC compliance:
This equipment has been tested and found to comply with the limits for a digital device,
pursuant to part 15 of the FCC Rules. This equipment generate, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the guide, may cause
harmful interference to radio communication.
For class A device, these limits are designed to provide reasonable protection against
harmful interference in a commercial environment. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
For class B device, these limits are designed to provide reasonable protection against
harmful interference in a residential installation. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

Table of Contents VI
Table of Contents
1 Foreword ................................................................................................................................................. I
Important Safeguards and Warnings .................................................................................................... III
Regulatory Information............................................................................................................................V
1 Introduction............................................................................................................................................ 1
General.......................................................................................................................................... 1
Features ........................................................................................................................................ 1
2 Design..................................................................................................................................................... 2
Dimension .....................................................................................................................................2
Cable............................................................................................................................................. 3
3 Installation.............................................................................................................................................. 5
Installing Model A.......................................................................................................................... 5
Installing Model B (1) and Model B (2) .........................................................................................6
Installing Model C.......................................................................................................................... 7
Installing Model D.......................................................................................................................... 8
Installing Model E........................................................................................................................10
Installing Model F.........................................................................................................................11
Installing Model G (1) and Model G (2)....................................................................................... 12
4 General Configuration ........................................................................................................................ 14
Opening Main Menu....................................................................................................................14
SettingAudio Input...................................................................................................................... 15
Operating OSD Menu.................................................................................................................. 16
5 Maintenance......................................................................................................................................... 18

Introduction 1
1 Introduction
General
This series of products comply with the HDCVI standard and support the transmission of video
and control signal over coaxial cable. They produce video signal with megapixel resolution and
require XVR device that comply with the HDCVI standard to achieve high speed, long distance,
and zero lag transmission of the signal. They are applicable to cover the high definition
monitoring needs for locations with low ambient light, including road, warehouse, underground
parking lot, bar, pipeline, and gas station.
Features
720p series support over 800 meter real-time transmission of video and control signal from
RG59 cable; for 1080p and above, the distance is 500 meter.
Support adjusting zoom and focus on XVR with motorized varifocal lens (available on
select model).
Excellent low-light performance with IR or night vision technology.
Configuring devices easily with OSD menu.
Support switching between HD and SD outputs.

Design 2
2 Design
Dimension
Model A(mm [in.])
Model B (1) and Model B (2) (mm [in.])
Model C (mm [in.])
Model D (mm [in.])

Design 3
Model E (mm [in.])
Model F (mm [in.])
Model G (1) and Model G (2) (mm [in.])
Cable
Cable type might vary with different cameras, and the actual product shall prevail.
Cable list
For more information about cable ports, see Table 2-1; for the operation method of ④(DIP
switch), see Table 2-2.

Design 4
Table 2-1 Cable function
No.
Port Name
Function
①
12V DC Power
Input
Inputs 12V DC power. Please be sure to supply power as
instructed in the Manual.
Device abnormity or damage could occur if power is not
supplied correctly.
②
Video Output
Connects to XVR to output video signal.
③
Audio Input
Connects to sound-pick-up devices to receive audio signal.
④
DIP Switch
Dial switches to change output mode. Switch up indicates "ON",
switch down indicates "OFF."
Table 2-2 DIP switch operation
Switch1
Switch2
Output Mode
OFF
OFF
CVI
ON
ON
CVBS
ON
OFF
AHD
OFF
ON
TVI

Installation 5
3 Installation
Make sure the mounting surface is strong enough to hold at least three times of the camera
weight.
The following figures are for reference only, and the actual product shall prevail.
Installing Model A
Model Ainstallation
Table 3-1 Installation item list
No.
Item
No.
Item
No.
Item
No.
Item
①
Mounting surface
②
Expansion bolt
③
Pedestal
④
Self-tapping screw
⑤
Fixing ring
⑥
Enclosure
⑦
Device
—
—
Hold the fixing ring⑤tightly and rotate the pedestal③counterclockwise to take it off.
Confirm the position of screw holes (and the cable outlet hole if it needs to go through
the mounting surface①) and drill them on the mounting surface①, and then insert the
expansion bolts②in the screw holes.
Align the screw holes on the pedestal③to those on the mounting surface①, and then
pull the cable out through mounting surface or the side cable tray. Attach the pedestal
③to the mounting surface①with the self-tapping screws④.
Put the fixing ring⑤and the enclosure⑥back on to the hold the device⑦, and then
connect the device⑦to power source and the XVR device, and the live view screen is
displayed.

Installation 6
Aim the lens to the ideal angle, and then adjust the focus and zoom until you get clear
image, see Figure 3-2. Fasten the fixing ring⑤afterwards.
Model Aadjustment
Installing Model B (1) and Model B (2)
Model B (1) and Model B (2) installation
Table 3-2 Installation item list
No.
Item
No.
Item
No.
Item
No.
Item
①
Mounting surface
②
Expansion bolt
③
Pedestal
④
Self-tapping screw
⑤
Device
⑥
Locking screw
⑦
Enclosure
—
—
Loosen the locking screw⑥with the supplied wrench and take the pedestal③off.
Confirm the position of screw holes (and the cable outlet hole if it needs to go through
the mounting surface①) and drill them on the mounting surface①, and then insert the
expansion bolts②in the screw holes.
Align the screw holes on the pedestal③to those on the mounting surface①, and then
pull the cable out through mounting surface or the side cable tray. Attach the pedestal
③to the mounting surface①with the self-tapping screws④.

Installation 7
Put the locking screw⑥and the enclosure⑦back on to the hold the device⑤, and
then connect the device⑤to power source and the XVR device, and the live view
screen is displayed.
Aim the lens to the ideal angle, and then fasten the locking screw⑥, see Figure 3-4.
Model B (1) and Model B (2) adjustment
Installing Model C
Model C installation
Table 3-3 Installation item list
No.
Item
No.
Item
No.
Item
No.
Item
①
Mounting surface
②
Expansion bolt
③
Pedestal
④
Self-tapping screw
⑤
Device
⑥
Enclosure
⑦
Fixing ring
—
—
Hold the fixing ring⑦tightly and rotate the pedestal③counterclockwise to take it off.
Confirm the position of screw holes (and the cable outlet hole if it needs to go through
the mounting surface①) and drill them on the mounting surface①, and then insert the
expansion bolts②in the screw holes.

Installation 8
Align the screw holes on the pedestal③to those on the mounting surface①, and then
pull the cable out through mounting surface or the side cable tray. Attach the pedestal
③to the mounting surface①with the self-tapping screws④.
Put the fixing ring⑦and the enclosure⑥back on to the hold the device⑤, and then
connect the device⑤to power source and the XVR device, and the live view screen is
displayed.
Adjust the focus and zoom as needed and aim the lens to the ideal angle, and then
fasten the fixing ring⑦, see Figure 3-6.
Model C adjustment
Installing Model D
Model D installation

Installation 9
Table 3-4 Installation item list
No.
Item
No.
Item
No.
Item
①
Mounting surface
②
Expansion bolt
③
Pedestal
④
Self-tapping screw
⑤
Device
⑥
Enclosure
Slightly squeeze the enclosure⑥and take the pedestal③off.
Confirm the position of screw holes (and the cable outlet hole if it needs to go through
the mounting surface①) and drill them on the mounting surface①, and then insert the
expansion bolts②in the screw holes.
Align the screw holes on the pedestal③to those on the mounting surface①, and then
pull the cable out through mounting surface or the side cable tray. Attach the pedestal
③to the mounting surface①with the self-tapping screws④.
Put the enclosure⑥back on, and then connect the device⑤to power source and the
XVR device, and the live view screen is displayed.
Aim the lens to the ideal angle, see Figure 3-8.
Model D adjustment

Installation 10
Installing Model E
Model E installation
Table 3-5 Installation item list
No.
Item
No.
Item
No.
Item
No.
Item
①
Mounting surface
②
Expansion bolt
③
Pedestal
④
Screw cover
⑤
Self-tapping screw
⑥
Device
⑦
Enclosure
⑧/⑨
Locking screw
Loosen the locking screws⑧/⑨with the supplied wrench and take the pedestal③off.
Confirm the position of screw holes (and the cable outlet hole if it needs to go through
the mounting surface①) and drill them on the mounting surface①, and then insert the
expansion bolts②in the screw holes.
Align the screw holes on the pedestal③to those on the mounting surface①, and then
pull the cable out through mounting surface or the side cable tray. Put the screw covers
in the screw holds on the pedestal③, and then attach the pedestal③to the mounting
surface①with the self-tapping screws④.
Put the locking screws⑧/⑨and the enclosure⑦back on to the hold the device⑥,
and then connect the device⑥to power source and the XVR device, and the live view
screen is displayed.
Aim the lens to the ideal angle, and then fasten the locking screws⑧/⑨, see Figure
3-10.

Installation 11
Model E adjustment
Installing Model F
Model F installation
Table 3-6 Installation item list
No.
Item
No.
Item
No.
Item
No.
Item
①
Mounting surface
②
Expansion bolt
③
Pedestal
④
Self-tapping screw
⑤
Device
⑥
Enclosure
⑦
Fixing ring
—
—
Hold the fixing ring⑦tightly and rotate the pedestal③as the open sign shows to take
the fixing ring⑦off.
Slightly squeeze the enclosure⑥and take the pedestal③off.
Confirm the position of screw holes (and the cable outlet hole if it needs to go through
the mounting surface①) and drill them on the mounting surface①, and then insert the
expansion bolts②in the screw holes.
Align the screw holes on the pedestal③to those on the mounting surface①, and then
pull the cable out through mounting surface or the side cable tray. Attach the pedestal
③to the mounting surface①with the self-tapping screws④.

Installation 12
Put the fixing ring⑦and the enclosure⑥back on, and then connect the device⑤to
power source and the XVR device, and the live view screen is displayed.
Aim the lens to the ideal angle, see Figure 3-12.
Model F adjustment
Installing Model G (1) and Model G (2)
Model G (1) and Model G (2) installation
Table 3-7 Installation item list
No.
Item
No.
Item
No.
Item
No.
Item
①
Mounting surface
②
Positioning map
③
Expansion bolt
④
Pedestal
⑤
Self-tapping screw
⑥
Device
⑦
Locking screw
⑧
Enclosure
Loosen the locking screw⑦with the supplied wrench and take the pedestal④off.
Confirm the position of screw holes (and the cable outlet hole if it needs to go through
the mounting surface①) as the positioning map②shows and drill them on the
mounting surface①, and then insert the expansion bolts③in the screw holes.
Align the screw holes on the pedestal④to those on the mounting surface①, and then
pull the cable out through mounting surface or the side cable tray. Attach the pedestal
④to the mounting surface①with the self-tapping screws⑤.

Installation 13
Put the locking screw⑦and the enclosure⑧back on to the hold the device⑥, and
then connect the camera to power source and the XVR device, and the live view screen
is displayed.
The adjustment way of model G (1) is different from which of model G (2).
For model G (1)
1) Aim the lens to the ideal angle, and then fasten the locking screw, see Figure 3-14.
Model G (1 and Model G (2) adjustment
2) In the PTZ setting interface (Figure 4-5), click + or –at Zoom and Focus to adjust
the zoom and focus until you get clear image.
For model G (2), aim the lens to the ideal angle, and then fasten the locking screw,
see Figure 3-14.