Dahua IPC-HFW2200R-VF User manual

Dahua HD IR Vari-Focal Fixed Network Camera User’s Manual
Dahua HD IR Vari-Focal Fixed Network Camera
User’s Manual
Version 1.0.0
Zhejiang Dahua Technology CO., LTD

Dahua HD IR Vari-Focal Fixed Network Camera User’s Manual
i
Welcome
Thank you for purchasing our network camera!
This user’s manual is designed to be a reference tool for your system.
Please read the following safeguard and warnings carefully before you use this series product!
Please keep this user’s manual well for future reference!

Dahua HD IR Vari-Focal Fixed Network Camera User’s Manual
ii
Important Safeguards and Warnings
1．Electrical safety
All installation and operation here should conform to your local electrical safety codes.
The power shall conform to the requirement in the SELV (Safety Extra Low Voltage) and the Limited
power source is rated 12V DC or 24V AC in the IEC60950-1. (Refer to general introduction)
Please note: Do not connect two power supplying sources to the device at the same time; it may
result in device damage! The product must be grounded to reduce the risk of electronic shock.
We assume no liability or responsibility for all the fires or electrical shock caused by improper handling
or installation.
We are not liable for any problems caused by unauthorized modification or attempted repair.
2．Transportation security
Heavy stress, violent vibration or water splash are not allowed during transportation, storage and
installation.
3．Installation
Do not apply power to the camera before completing installation.
Please install the proper power cut-off device during the installation connection.
Always follow the instruction guide the manufacturer recommended.
4．Qualified engineers needed
All the examination and repair work should be done by the qualified service engineers.
We are not liable for any problems caused by unauthorized modifications or attempted repair.
5．Environment
This series network camera should be installed in a cool, dry place away from direct sunlight,
inflammable, explosive substances and etc.
Please keep it away from the electromagnetic radiation object and environment.
Please make sure the CCD (CMOS) component is out of the radiation of the laser beam device.
Otherwise it may result in CCD (CMOS) optical component damage.
Please keep the sound ventilation.
Do not allow the water and other liquid falling into the camera.
Thunder-proof device is recommended to be adopted to better prevent thunder.
The grounding studs of the product are recommended to be grounded to further enhance the reliability
of the camera.
6. Daily Maintenance
Please shut down the device and then unplug the power cable before you begin daily maintenance
work.

Dahua HD IR Vari-Focal Fixed Network Camera User’s Manual
iii
Do not touch the CCD (CMOS) optic component. You can use the blower to clean the dust on the lens
surface.
Always use the dry soft cloth to clean the device. If there is too much dust, please use the water to
dilute the mild detergent first and then use it to clean the device. Finally use the dry cloth to clean the
device.
Please put the dustproof cap to protect the CCD (CMOS) component when you do not use the camera.
Dome enclosure is the optical component, do not touch the enclosure when you are installing the
device or clean the enclosure when you are doing maintenance work. Please use professional optical
clean method to clean the enclosure. Improper enclosure clean method (such as use cloth) may result
in poor IR effect of camera with IR function.
7. Accessories
Be sure to use all the accessories recommended by manufacturer.
Before installation, please open the package and check all the components are included.
Contact your local retailer ASAP if something is broken in your package.
Accessory Name
Amount
Network Camera Unit
1
Quick Start Guide
1
Installation Accessories Bag
1
CD
1
Warranty Card and Certificate
1

Dahua HD IR Vari-Focal Fixed Network Camera User’s Manual
iv
Table of Contents
1General Introduction ..................................................................................................................1
1.1 Overview........................................................................................................................1
1.2 Features.........................................................................................................................1
1.3 Specifications................................................................................................................2
1.3.1 Performance...........................................................................................................2
2Framework...................................................................................................................................6
2.1 Device External Cable .................................................................................................6
2.2 Framework and Dimension.........................................................................................6
3Device Installation ......................................................................................................................8
4Quick Configuration Tool.........................................................................................................11
4.1 Overview......................................................................................................................11
4.2 Operation.....................................................................................................................11
5Web Operation..........................................................................................................................13
5.1 Network Connection...................................................................................................13
5.2 Login and Main Interface...........................................................................................13
6FAQ ............................................................................................................................................15
Appendix Toxic or Hazardous Materials or Elements ...............................................................16

Dahua HD IR Vari-Focal Fixed Network Camera User’s Manual
1
1General Introduction
1.1 Overview
This series network camera integrates the traditional camera and network video technology. It adopts
video data collection, transmission together. It can connect to the network directly without any auxiliary
device.
This series network camera uses standard H.264 video compression technology, which maximally
guarantees the video quality.
It supports the IR night vision function. In the night environments, the device can use the IR light to
highlight the object which is suitable for the surveillance function in the low illumination environments.
The built-in waterproof design conforms to the IP 66 level. It has the sound waterproof function
suitable for use in the outdoor environments.
It can be used alone or used in a network area. When it is used lonely, you can connect it to the
network and then use a network client-end. Due to its multiple functions and various uses, this series
network camera is widely used in many environments such as home, office, bank, road monitor and
etc.
1.2 Features
User
Management
Different user rights for each group, one user belongs to one group.
The user right shall not exceed the group right.
Storage
Function
Support central server backup function in accordance with your configuration
and setup in alarm or schedule setting
Support record via Web and the recorded file are storage in the client-end
PC.
Support network storage function such as FTP.
Data
Transmission
Support data transmission via Ethernet.
Network
Monitor
Network camera supports one-channel video data transmit to network
terminal and then decode. Delay is within 270ms (network bandwidth support
needed)
Max supports 20 connections.
Adopt the following video transmission protocol: HTTP, TCP, UDP,
MULTICAST, RTP/RTCP, RTSP and etc.
Support web access.
Network
Management
Realize network camera configuration and management via Ethernet.
Support device management via web or client-end.
Support abundant network protocols.
Power
External power adapter DC12V.
Support PoE.
Warning！
Do not connect these two power supplying sources to the device at the
same time; it may result in device damage!
Assistant
Function
Log function
Support system resource information and running status real-time display.
Day/Night mode auto switch.(with ICR switch)
Support picture parameter setup such as electronic shutter and gain setup.
Backlight compensation: screen auto split to realize backlight compensation

Dahua HD IR Vari-Focal Fixed Network Camera User’s Manual
2
to adjust the bright.
Support digital WDR.
Support video watermark function to avoid vicious video modification.
Support dual bit streams, ACF.
1.3 Specifications
1.3.1 Performance
Please refer to the following sheet for network camera performance specification.
Model
Parameter
IPC-HFW2100R-VF
IPC-HFW2200R-VF
IPC-HFW2300R-VF
System
Main Processor
High performance DSP
OS
Embedded LINUX
System
Resources
Support real-time network monitoring, local record, and remote
operation at the same time.
User Interface
Remote operation interface such as WEB, DSS, PSS
System Status
Bit stream statistics, log, and software version.
Video Parameter
Image Sensor
1/3-inch CMOS
1/2.8-inch CMOS
1/3-inch CMOS
Scan Pixel
1280(H)*960(V)
1920(H)*1080(V)
2048(H)*1536(V)
Day/Night Mode
Support day/night mode switch.
Gain Control
Fixed/Auto
White Balance
Manual/Auto
BLC
On/Off
Electronic
Shutter
Auto/Manual
It ranges from 1/3 to 1/100000.
Video
Compression
Standard
H.264/H.264H/MJPEG
Video Frame
Rate
PAL:
Main stream
(1280*960@25fps)
Extra Stream 1
(704*576@25fps),
Extra Stream 2
(1280*720@8fps)
PAL:
Main stream
(1920*1080@25fps)
Extra Stream 1
(704*576@25fps),
Extra Stream 2
(1280*720@11fps)
PAL:
Main stream
(2048*1536@20fps)
Extra Stream 1
(704*576@20fps),
Extra Stream 2
(1280*720@1fps)
Main Stream
(1920*1080@25fps)
Extra Stream 1
(704*576@25fps),
Extra Stream 2
(1280*720@11fps)
NTSC:
Main stream
(1280*960@30fps)
extra stream 1
(704*480@30fps),
Extra Stream 2
(1280*720@1fps)
NTSC:
Main stream
(1920*1080@30fps)
Extra Stream 1
(704*480@30fps),
Extra Stream 2
(1280*720@1fps)
NTSC:
Main stream
(2048*1536@20fps)
Extra Stream 1
(704*480@20fps),
Extra Stream 2
(1280*720@1fps)
Main Stream
(1920*1080@30fps)
Extra Stream 1
(704*480@30fps),
Extra Stream 2

Dahua HD IR Vari-Focal Fixed Network Camera User’s Manual
3
(1280*720@1fps)
Note:
The exact frame rate of extra stream 2 is decided by device max
capacity set, it is dynamic and adjustable during the range of max
capacity set.
Video Bit Rate
H.264H: 40Kbps-8192Kbps; adjustable.
MJPEG: 40Kbps-16384Kbps; adjustable and bit rate is adjustable.
Support customized setup. (The actual bit rate is subject to device
adjustable range)
Video Flip
Support mirror.
Supports flip, corridor mode function.
Snapshot
Max 1f/s snapshot. File extension name is JPEG.
Privacy Mask
Supports max 4 privacy mask zones
ROI
Supports max 4 ROI zones
Video Setup
Support parameter setup such as bright, contrast and acutance.
Video
Information
Channel title, time title, motion detect, tampering, overlay.
Lens
2.8～12mm/F1.4(manual focus)
Lens Interface
φ14 port, Lens is the default accessories
Video
Motion Detect
396 (18*22) detection zones; sensitivity level ranges from 0 to 100;
area threshold ranges from 0 to 100.
Video Tampering
Sensitivity level 1-6, each level is corresponding to the tampered zone
percentage of the video
Activation event: video storage, image snapshot, log, email function
and etc.
Recor d and Backu p
Video Priority
Manual>Video detect>Schedule
Storage
Management
Support NAS storage
Network
Wired Network
1-channel wired Ethernet port, 10/100 Base-T Ethernet
Network Protocol
Standard,HTTP,TCP/IP,ARP,IGMP,ICMP,RTSP,RTP,UDP,RTCP,SMT
P,FTP,DHCP,DNS,DDNS,PPPoE,UPnP,NTP,Bonjour,SNMP,Qos,802.
1x
Remote
Operation
Monitor, system setup, file download, log information, maintenance ,
upgrade and etc.
Platform
Interface
Protocol
PSIA, ONVIF
General Parameter
Power
DC12V power, PoE power supply
Power
Consumption
4.5W MAX
Working
Temperature
-30℃~+60℃
Working
Humidify
≤95%
Dimensions(mm)
72*80*212.8
Weight
650g
Installation
Installation with the bracket.

Dahua HD IR Vari-Focal Fixed Network Camera User’s Manual
4
Model
Parameter
IPC-HFW2100R-Z
IPC-HFW2200R-Z
IPC-HFW2300R-Z
System
Main Processor
High performance DSP
OS
Embedded LINUX
System
Resources
Support real-time network monitoring, local record, and remote
operation at the same time.
User Interface
Remote operation interface such as WEB, DSS, PSS
System Status
Bit stream statistics, log, and software version.
Video Parameter
Image Sensor
1/3-inch CMOS
1/2.8-inch CMOS
1/3-inch CMOS
Scan Pixel
1280(H)*960(V)
1920(H)*1080(V)
2048(H)*1536(V)
Day/Night Mode
Support day/night mode switch.
Gain Control
Fixed/Auto
White Balance
Manual/Auto
BLC
On/Off
Electronic
Shutter
Auto/Manual
It ranges from 1/3 to 1/100000.
Video
Compression
Standard
H.264/H.264H/MJPEG
Video Frame
Rate
PAL:
Main stream
(1280*960@25fps)
Extra Stream 1
(704*576@25fps),
Extra Stream 2
(1280*720@8fps)
PAL:
Main stream
(1920*1080@25fps)
Extra Stream 1
(704*576@25fps),
Extra Stream 2
(1280*720@11fps)
PAL:
Main stream
(2048*1536@20fps)
Extra Stream 1
(704*576@20fps),
Extra Stream 2
(1280*720@1fps)
Main Stream
(1920*1080@25fps)
Extra Stream 1
(704*576@25fps),
Extra Stream 2
(1280*720@11fps)
NTSC:
Main stream
(1280*960@30fps)
extra stream 1
(704*480@30fps),
Extra Stream 2
(1280*720@1fps)
NTSC:
Main stream
(1920*1080@30fps)
Extra Stream 1
(704*480@30fps),
Extra Stream 2
(1280*720@1fps)
NTSC:
Main stream
(2048*1536@20fps)
Extra Stream 1
(704*480@20fps),
Extra Stream 2
(1280*720@1fps)
Main Stream
(1920*1080@30fps)
Extra Stream 1
(704*480@30fps),
Extra Stream 2
(1280*720@1fps)
Note:
The exact frame rate of extra stream 2 is decided by device max
capacity set, it is dynamic and adjustable during the range of max
capacity set.
Video Bit Rate
H.264H: 40Kbps-8192Kbps; adjustable.

Dahua HD IR Vari-Focal Fixed Network Camera User’s Manual
5
MJPEG: 40Kbps-16384Kbps; adjustable and bit rate is adjustable.
Support customized setup. (The actual bit rate is subject to device
adjustable range)
Video Flip
Support mirror.
Supports flip, corridor mode function.
Snapshot
Max 1f/s snapshot. File extension name is JPEG.
Privacy Mask
Supports max 4 privacy mask zones
ROI
Supports max 4 ROI zones
Video Setup
Support parameter setup such as bright, contrast and acutance.
Video
Information
Channel title, time title, motion detect, tampering, overlay.
Lens
2.8～12mm/F1.4(motorized focus)
Lens Interface
φ14 port, Lens is the default accessories
Video
Motion Detect
396 (18*22) detection zones; sensitivity level ranges from 0 to 100;
area threshold ranges from 0 to 100.
Video Tampering
Sensitivity level 1-6, each level is corresponding to the tampered zone
percentage of the video
Activation event: video storage, image snapshot, log, email function
and etc.
Recor d and Backu p
Video Priority
Manual>Video detect>Schedule
Storage
Management
Support NAS storage
Network
Wired Network
1-channel wired Ethernet port, 10/100 Base-T Ethernet
Network Protocol
Standard,HTTP,TCP/IP,ARP,IGMP,ICMP,RTSP,RTP,UDP,RTCP,SMT
P,FTP,DHCP,DNS,DDNS,PPPoE,UPnP,NTP,Bonjour,SNMP,Qos,802.
1x
Remote
Operation
Monitor, system setup, file download, log information, maintenance ,
upgrade and etc.
Platform
Interface
Protocol
PSIA, ONVIF
General Parameter
Power
DC12V power, PoE power supply
Power
Consumption
8.5W MAX (4.5 W when not focusing)
Working
Temperature
-40℃~+60℃
Working
Humidify
≤95%
Dimensions(mm)
72*80*212.8
Weight
650g
Installation
Installation with the bracket.

Dahua HD IR Vari-Focal Fixed Network Camera User’s Manual
6
2Framework
2.1 Device External Cable
You can refer to the following figure for cable information. See Figure 2-1.
Figure 2-1
Please refer to the following sheet for detailed information.
SN
Port
Port Name
Connection
Note
1
LAN
Network port
Ethernet
port
Connect to standard Ethernet cable.
Note:
Before making crystal head, pull the
anti-dust cover (default), waterproof
cover (optional) through network cable.
2
DC 12V
Power input port
-
Power port. Input DC 12V.
2.2 Framework and Dimension
Please refer to the following figure for dimension information. The unit is mm. See Figure 2-2 and
Figure 2-3.

Dahua HD IR Vari-Focal Fixed Network Camera User’s Manual
7
Figure 2-2
Figure 2-3

Dahua HD IR Vari-Focal Fixed Network Camera User’s Manual
8
3Device Installation
Important
Please make sure the installation surface can min support the 3X weight of the camera and the
bracket.
Step 1
Open accessories bag, take out installation position map and stick it to designated surface where you
will install the device (wall or ceiling).
Step 2
Dig a hole according to position of hole on installation position map.
Step 3
Open accessories bag, take out expansion bolts and insert them into the holes you just dug.
Step 4
Open accessories bag and take out the self-tapping screws. Aim the expansion bolts to the installation
holes on the device pedestal and fix the device on the installation surface (wall or ceiling) with self-
tapping screws.
Step 5
Plug external wiring of the device properly.
Figure 3-1

Dahua HD IR Vari-Focal Fixed Network Camera User’s Manual
9
Figure 3-2
Step 6
Use inner hex screwdriver to loosen adjusting screw shown in Figure 2-2.
Step 7
Adjust the device in all possible directions, and set its monitoring direction.
Step 8
Use inner hex screwdriver to tighten the adjusting screws.
Figure 3-3

Dahua HD IR Vari-Focal Fixed Network Camera User’s Manual
10
Step 9
Screw out the pan head screw (shown in Figure 2-3) by cross head screwdriver and take off the lower
cover.
Step 10
Adjust the lens focus lever and set its monitoring direction more accurately by external focus.
Step 11
Use cross head screwdriver to tighten the pan head screws.

Dahua HD IR Vari-Focal Fixed Network Camera User’s Manual
11
4 Quick Configuration Tool
4.1 Overview
Quick configuration tool can search current IP address, modify IP address. At the same time, you can
use it to upgrade the device.
Please note the tool only applies to the IP addresses in the same segment.
4.2 Operation
Step 1
Double click the “ConfigTools.exe” icon; you can see an interface is shown as in Figure 4-1.
In the device list interface, you can view device IP address, port number, subnet mask, default
gateway, MAC address and etc.
Step 2
Select one IP address and then right click mouse, you can see an interface is shown as in Figure 4-2.
Select the “Open Device Web” item; you can go to the corresponding web login interface.
Figure 4-1 Search interface

Dahua HD IR Vari-Focal Fixed Network Camera User’s Manual
12
Figure 4-2 Search interface 2
If you want to modify the device IP address without logging in the device web interface, you can go to
the configuration tool main interface to set.
In the configuration tool search interface (Figure 4-1), please select a device IP address and then
double click it to open the login interface. Or you can select an IP address and then click the Login
button to go to the login interface. See Figure 4-3.
In Figure 4-3, you can view device IP address, user name, password and port. Please modify the
corresponding information to login.
Please note the port information here shall be identical with the port value you set in TCP port in Web
Network interface. Otherwise, you cannot login the device.
If you are using device background upgrade port 3800 to login, other setups are all invalid.
Figure 4-3 Login prompt
After you logged in, the configuration tool main interface is shown as below. See Figure 4-4.
Figure 4-4 Main interface
For detailed information and operation instruction of the quick configuration tool, please refer
to the Quick Configuration Tool User’s Manual included in the resources CD.

Dahua HD IR Vari-Focal Fixed Network Camera User’s Manual
13
5 Web Operation
This series network camera products support the Web access and management via PC.
Web includes several modules: Monitor channel preview, system configuration, alarm and etc.
5.1 Network Connection
Please follow the steps listed below for network connection.
Make sure the network camera has connected to the network properly.
Please set the IP address, subnet mask and gateway of the PC and the network camera
respectively. Network camera default IP address is 192.168.1.108. Subnet mask is 255.255.255.0.
Gateway is 192.168.1.1
Use order ping ***.***.***.***(* network camera address) to check connection is OK or not.
5.2 Login and Main Interface
Open IE and input network camera address in the address bar. See Figure 5- 1.
Figure 5- 1 IP address
The login interface is shown as below. See Figure 5- 2.
Please input your user name and password.
Default factory name is admin and password is admin.
Note: For security reasons, please modify your password after you first login.
Input your IP
address here

Dahua HD IR Vari-Focal Fixed Network Camera User’s Manual
14
Figure 5- 2 Web login
After you successfully logged in, please install WEB plug-in unit. Please refer to the Web Operation
Manual included in the resource CD for detailed operation instruction.
See Figure 5- 3.
Figure 5- 3 Web monitoring window

Dahua HD IR Vari-Focal Fixed Network Camera User’s Manual
15
6FAQ
Bug
The water leakage
occurred.
The unauthorized front or rear cap remove may result in water
leakage.
The glass front cap has sustained heavy push or strike.
The waterproof plug of the rear cap becomes loosen.
The waterproof test hole screw become loose, or the waterproof
test thread was used as GND thread by mistake.
IR video is poor.
Did not use the proper supplying power. The IR light cannot
turn on completely.
The object is out of the IR distance range of current device.
IR-CUT does not turn to the night mode. The photosensitive
chip of the front-end can not sense the IR light.
Sunshade cover screw becomes loose, which causes the
sunshade cover move forward and light arc occurs to the
image. Solution: move the sunshade cover to the rearmost
position and lock it firmly.
I cannot upgrade
the device via
network.
When network upgrade operation failed, you can use port 3800 to
continue upgrade.
I cannot login the
client-end or the
WEB.
For Windows OS 98 or Windows ME user, if you cannot install
the client-end or cannot view after the installation. We
recommend the win2000 sp4 OS or higher, or install the client-
end of the low version.
The Active X control is blocked.
The display card version shall be dx8.1 or higher.
Network connection error occurred.
Invalid network setup.
Invalid user name or password.
Client version and device program do not match.
I cannot play the
download file.
There is no player.
There is no DX8.1 or higher.
For the MEDIA PLAYER, there shall be Div X503Bundle.exe
plug in if you play the .AVI file.
For Windows XP user, you need to install the plug in
DivX503Bundle.exe and ffdsho-2004 1012.exe.
To guarantee
setup update
After you modified the important setup, please reboot the device via
the software to make sure the setup has been updated to the
storage medium.
Power adapter
The general power adapter can work ranging from 0℃to 40 ℃.
The device may result in unstable power supply when the
temperature exceeds the working temperature.
Please replace an industry-level power adapter if you are using
in the harsh environments.