Dahua HAC-HFW2200EP User manual

2 Megapixel HDCVI Camera User’s Manual
Version 1.0.1

i
Table of Contents
1General Introduction ..................................................................................................................1
1.1 Overview........................................................................................................................1
1.2 Features.........................................................................................................................1
1.3 Functions .......................................................................................................................1
1.4 Specifications................................................................................................................1
2Framework...................................................................................................................................4
2.1 Dimensions....................................................................................................................4
2.2 Structure ........................................................................................................................4
3Installation ...................................................................................................................................6
4Menu.............................................................................................................................................8
4.1 Menu List .......................................................................................................................8
4.2 Note ..............................................................................................................................10
Appendix Toxic or Hazardous Materials or Elements ...............................................................12

ii
Welcome
Thank you for purchasing our HDCVI camera!
This user’s manual is designed to be a reference tool for your system.
Please read the following safeguard and warnings carefully before you use this series product!
Please keep this user’s manual well for future reference!

iii
Important Safeguards and Warnings
1．Electrical safety
All installation and operation here should conform to your local electrical safety codes.
The power shall conform to the requirement in the SELV (Safety Extra Low Voltage) and the Limited
power source is rated 12V DC in the IEC60950-1.
We assume no liability or responsibility for all the fires or electrical shock caused by improper handling
or installation.
2．Transportation security
Heavy stress, violent vibration or water splash are not allowed during transportation, storage and
installation.
3．Installation
Do not apply power to the camera before completing installation.
Please install the proper power cut-off device during the installation connection.
Always follow the instruction guide the manufacturer recommended.
If this product is installed in the ceiling, please make sure the installation position can sustain the min
50N.
4．Qualified engineers needed
All the examination and repair work should be done by the qualified service engineers.
We are not liable for any problems caused by unauthorized modifications or attempted repair.
5．Environment
This series HDCVI camera should be installed in a cool, dry place away from direct sunlight or strong
light, inflammable, explosive substances and etc.
This series camera shall work on the specified working temperature. Please keep it away from the
electromagnetic radiation object and environment.
Please make sure the CMOS component is out of the radiation of the laser beam device. Otherwise it
may result in CMOS optical component damage.
Please keep the sound ventilation.
Do not allow the water and other liquid falling into the camera.
6. Accessories
Be sure to use all the accessories recommended by manufacturer.
Before installation, please open the package and check all the components are included.
Contact your local retailer ASAP if something is broken in your package.
7. Daily Maintenance

iv
Please shut down the device and then unplug the power cable before you begin daily maintenance
work.
Use the dry soft cloth to clean the device. If there is too much dust, please use the water to dilute the
mild detergent first and then use it to clean the device. Finally use the dry cloth to clean the device.
Please put the dustproof cap to protect the CMOS component when you do not use the camera.

1
1General Introduction
1.1 Overview
This series megapixel HD camera conforms to the HDCVI standard. It supports video signal
high-speed long distance transmission without any delay. It can be controlled by the DVR
conforming to the HDCVI.
1.2 Features
zHigh-performance CMOS image sensor, megapixel definition.
zHD video, coaxial cable to transmit the control signal.
zSupport 75-3 coaxial cable transmission without any loss. Transmission distance is over
300m.
zSupport HD and standard definition switch.
zSupport 1080P@25, 1080P@30, 720P@25, 720P@30, 720P@50, 720P@60.
zHigh speed, long distance real-time transmission.
zSupport OSD (on-screen display), suitable for user self-defined setup.
zSupport privacy mask, image digital zoom.
zSupport DC12V power supplying.
zSupport 3D noise reduction(denoise),excellent performance in low illumination
environment.
zIP66 compliance.
zSupport ICR switch to realize surveillance both in the daytime and at night.
zSupport intelligent IR function.
1.3 Functions
HDCVI Specification
HDCVI（High Definition Composite Video Interface）is an over-coaxial –cable HD video
transmission standard. The technology renders two HD video formats by progressive scanning.
OSD
User-friendly on-screen display for you to select the different functions.
ICR
The IR cut removal is to filter the IR light in the daytime and then auto switch to the general
fitter at night. This function allows the camera to output the high sensitivity and clear video.
Smart IR technology
The sensor controls the IR light on/off via the combination work of the hardware and software,
which realizes the automatically IR light compensation according to the environment
illumination.
1.4 Specifications

2
Please refer to the following sheet for specification.
2 Megapixel HDCVI Camera
Model
Parameter HAC-HFW2200EP/N
Video Processor 1/3" 2 Megapixel CMOS
Video Format PAL/NTSC
Effective Pixel 1920 (H) *1080 (V)
Min Illumination 0.05Lux@（F1.2，AGC ON），0 Lux with IR
Electronic Shutter Support slow shutter. 1/3s～1/100,000s
Video Standard HDCVI/CVBS compliance
Video Frame Rate 1920×1080@25fps；1920×1080@30fps；1280×720@25 fps；
1280×720@30 fps；1280×720@50 fps；1280×720@60 fps
Lens Port M12
Lens Type 2.8/3.6/6/8mm optional
Day/Night Switch ICR mechanical auto switch
Video Output 1-channel HDCVI high definition video output/ CVBS standard definition video
output (Can switch.)
Denoise (Noise
Reduction) Support 2D/3D denoise.
OSD Menu Control Support coaxial cable control
EXPOSURE Exposure Mode/Exposure Level/Exposure Speed/Anti Flicker/BLC/Return
WHITE
BALANCE Auto/Manual/Day/Night/Return&Exit
DAY/NIGHT Auto/B&W/Color/ Return&Exit
FUNCTION 2DNR/3DNR/D-zoom/Lens/ Return&Exit
ADVANCED Cam Title/Mirror&Flip/Motion Detect/Privacy Mask/Language/COM
Setup/System Info/ Return&Exit
IMAGE Sharpness/Brightness/Contrastness/Saturation/Sharp Suppress/ Chroma
Suppress/Gamma/Video Format/ Return&Exit
RESET /
OSD
EXIT /
Max IR Distance 20m
IR Light Control Plan Advanced non-photosensor control plan
Transmission
Distance Over 300m via 75-3 coaxial cable.
Protection Level IP66
Working Temperature
/Humidity -30℃~+60℃. Humidity is less than 95%(no condensation)
Power DC 12V±10%
Power Consumption 4.5W MAX
(Input: 12V 0.38A)
Dimension(mm) 69.9×178.4×70 (Provide internal cable exit bracket )

3
Angle Adjustment Pan: 0°～360°: Tilt: 0°～90°: Flip: 0°～360°
Weight 500g
Installation Mode Wall mount

4
2Framework
2.1 Dimensions
Please refer to the following for dimension information. The unit is mm. See Figure 2-1.
Figure 2-1
2.2 Structure
Please refer to the following figure for structure information. See Figure 2-2.
Figure 2-2
Please refer to the following sheet for detailed information.

5
SN Name Function
1 Lens It is to receive the optical signal from the environments.
2 Sunshield Cover /
3 Bracket Support camera body and rotate to adjust monitor angle.
4 Power input port Connect to the DC 12V power to input the power.
5 Video output port
BNC port is to output HDCVI/CVBS standard definition video signal.
You can connect to the devices such as the DVR or the NVS
conforming to the HDCVI specifications.
6
Standard
definition/high
definition switch
control cable
When the standard definition/high definition switch control cable is
short circuit, system outputs standard definition video. Otherwise,
when the circuit is open, system outputs the high definition video.

6
3Installation
Important
zBefore the installation, please make sure the installation surface can sustain at
least 3X weight of the bracket and the camera.
Please refer to the steps listed below for installation information.
Figure 3-1
Step 1
Install the camera bracket according to your installation mode.
Before you install the bracket, please pull the cable through the cable exit of the
installation surface or pull the cable through the cable exit of the bracket.
zPlease install the expansion bolt if you want to install in the cement wall (Please make
sure the installation holes of the expansion bolts are the same with the bracket.) Then you
can install the bracket. See Figure 3-1.
zIf you want to install in the wood surface, please skip the first step and then use the self-
tapping screws to install the bracket directly.
Step 2
Put the two self-tapping screws to the two expansion blots at the top left and the top right.
Secure the bracket on the self-tapping screws. See (A) in Figure 3-1.
Important
The screw depth shall reserve 8mm-10mm to secure the bracket.

7
Step 3
Refer to Figure 3-1 to fix other two self-tapping screws and the secure. Now the camera is
fixed on the installation surface.
Step 4
Use the L wrench (provided) to loosen the adjusting screw to make the camera can monitor
the corresponding surveillance zone. Use the L wrench to adjust the adjusting screw to fix the
camera firmly. Please refer to (B) and (C) in Figure 3-1.
Step 5
Connect the video output port of the device cable to the rear-end encode device such as DVR
or NVS. Then connect the power port of the device cable to the corresponding power
supplying source.

8
4Menu
On DVR local interface, click the “+” button of the iris on the PTZ control interface, or on the
WEB interface, click the “+” button of the iris, you can open the menu interface.
Click up/down button to view all the items on the left pane of the following list. Click left/right
button to set the corresponding values on the right pane of the following list. If there is “…” on
the right pane, click the “+” button of the iris, you can open the 2nd menu interface. Repeat the
previous steps to set the value. If there is “ ” on the right pane, click the “+” button of the iris,
you can go to the next interface. Here you complete the setup and confirm. Click Return button
to go back to the previous menu interface.
4.1 Menu List
The 1st The 2nd The 3rd
Auto
Gain Max 0～100
Gain Min 0～100
Low
Noise
Return&Exit For the 2nd and the 3rd
menu, when you click Exit
button to exit, system
saves current setup by
default.
Shutter Max zPAL: 0ms～40ms
zNTSC: 0ms～33ms
Shutter Min zPAL: 0ms～40ms
zNTSC: 0ms～33ms
Low Motion
Blur
Return&Exit
Shutter 1/100000, 1/10000,
1/4000,1/2000,1/1000,1/500,
1/250,1/120,1/100,1/60,1/50,
1/30,1/25,1/15,1/12,1/10,1/8,
1/6,1/5,1/4,1/3
Customized
Gain Max 0～100
Gain Min 0～100
Exposure
Mode
Manual
Return&Exit
Exp Level 0～14
Exp Speed 0～7
Anti-flicker Outoodr/50H
Z/60HZ
z50HZ: 1/50, 1/100, 1/25,
1/10, 1/5, 1/4.
z60HZ: 1/60, 1/120, 1/30,
1/4, 1/12, 1/6.
The 50HZ and 60HZ mode
have different manual
exposure mode and there
is no low motion blur and
low noise exposure mode.
BLC OFF/ON
WDR 0～100
HLC 0～100
The HLC is valid when auto
exposure and outdoor anti-
flicker mode are both valid.
Exposure
BLC
Return&Exit
Auto
Blue 1～100
Red 1～100
White
Balance Manual
Return&Ex

9
The 1st The 2nd The 3rd
it
Day
Night
Auto
B/W
Day/Night
Color
2DNR 0～100
3DNR 0～100
D-Zoom 1～10
Lens Manual/DC
Function
Return&Ex
it
CAM
Title
Mirror OFF/ON
Flip OFF/ON
Mirror/Flip
Return&Exit
OFF
Area Sel 0～3
There are four motion detect
zones ranging from 0 to 3.
You need to set parameters
for each zone.
Area State OFF/ON
Sensitivity 0～100
Threshold 0～100
Position
Area Setup
Size
Use direction buttons to
set position and zone size.
Default
Motion
Detect ON
Return&Exit
OFF
Area Sel 0～7
There are eight privacy mask
zones ranging from 0 to 7.
You need to set parameters
for each zone.
Area state OFF/ON
Position
Area setup
Size
Use direction buttons to set
position and zone size.
Default
Privacy
Mask ON
Return&Exit
Language EN
Address 1～254
Apply
COM
Setup
Return&Exit
Version XXXXXXXXX
Advanced
System
Info Return&Exit
Sharpness 0～100
Brightness 0～100
Contrastne
ss
0～100
Saturation 0～100
Sharp
Suppress
0～100
Chroma
suppress
0～100
Gamma 0～5
Image
Video 1080P@25 OK/CANCEL

10
The 1st The 2nd The 3rd
Format /1080P@
30 /720P
@25 /720
P@30 /72
0P@50 /7
20P@60
Return&Exi
t
Reset
Exit
4.2 Note
Parameter Function
Brightness It is to adjust monitor window bright. The value ranges from 0 to
100. The default value is 50.
The larger the number is, the bright the video is. When you
input the value here, the bright section and the dark section of
the video will be adjusted accordingly. You can use this
function when the whole video is too dark or too bright. Please
note the video may become hazy if the value is too high. The
recommended value ranges from 40 to 60.
Contrast It is to adjust monitor window contrast. The value ranges from 0
to 100. The default value is 50.
The larger the number is, the higher the contrast is. You can
use this function when the whole video bright is OK but the
contrast is not proper. Please note the video may become hazy
if the value is too low. If this value is too high, the dark section
may lack brightness while the bright section may over
exposure .The recommended value ranges from 40 to 60.
Saturation It is to adjust monitor window saturation. The value ranges from
0 to 100. The default value is 50.
The larger the number, the strong the color is. This value has
no effect on the general brightness of the whole video. The
video color may become too strong if the value is too high. For
the grey part of the video, the distortion may occur if the white
balance is not accurate. Please note the video may not be
attractive if the value is too low. The recommended value
ranges from 40 to 60.
Sharpness The value here is to adjust the edge of the video. The value
ranges from 0 to 100. The larger the value is, the clear the edge
is and vice versa. Please note there is noise if the value here is
too high. The default value is 50 and the recommended value
ranges from 40 to 60.
3DNR It is to reduce video noise. The larger the number is, the lower
the noise is. The details of the video may disappear if the value
here is too large.

11
Anti-flicker zOutdoor: In this mode, you can switch exposure mode to
get the effect under the corresponding exposure mode.
z50Hz: When the current is 50Hz, system can auto adjust
the exposure according to the environment brightness in
case there is any strip.
z60Hz: When the current is 60Hz, system can auto adjust
the exposure according to the environment brightness in
case there is any strip.

12
Appendix Toxic or Hazardous Materials or Elements
Toxic or Hazardous Materials or Elements
Component
Name Pb Hg Cd Cr VI PBB PBDE
Circuit Board
Component ○○○○○○
Device
Construction
Material
○
○○○○○
Wire and Cable ○ ○○○○○
Packing
Components ○○○○○○
Accessories ○○○○○○
O: Indicates that the concentration of the hazardous substance in all homogeneous materials
in the parts is below the relevant threshold of the SJ/T11363-2006 standard.
X: Indicates that the concentration of the hazardous substance of at least one of all
homogeneous materials in the parts is above the relevant threshold of the SJ/T11363-2006
standard. During the environmental-friendly use period (EFUP) period, the toxic or hazardous
substance or elements contained in products will not leak or mutate so that the use of these
(substances or elements) will not result in any severe environmental pollution, any bodily injury
or damage to any assets. The consumer is not authorized to process such kind of substances
or elements, please return to the corresponding local authorities to process according to your
local government statutes.
Note
•This manual is for reference only. Slight difference may be found in the user
interface.
•All the designs and software here are subject to change without prior written
notice.
•All trademarks and registered trademarks mentioned are the properties of their
respective owners.
•If there is any uncertainty or controversy, please refer to the final explanation of
us.
•Please visit our website or contact your local service engineer for more
information.