Dahua Pro IPC-HDB4231C-AS User manual

Dahua HD Mini Network Dome Camera Quick Start Guide
Version 1.0.0
Zhejiang Dahua Vision Technology Co., LTD
Questo manuale d’istruzione è fornito da trovaprezzi.it. Scopri tutte le offerte per Dahua Pro IPC-
HDB4231C-AS o cerca il tuo prodotto tra le migliori offerte di Videosorveglianza

1
Welcome
Thank you for purchasing our Network camera!
This user’s manual is designed to be a reference tool for your system.
Please read the following safeguard and warnings carefully before you use this series product!
Please keep this user’s manual well for future reference!
Important Safeguards and Warnings
1．Electrical safety
All installation and operation here should conform to your local electrical safety codes.
Please check if the power supply is correct before operating the device.
The power shall conform to the requirement in the SELV (Safety Extra Low Voltage) and the
Limited power source is rated DC 12V or AC 24V in the IEC60950-1. (Power supply
requirement is subject to the device label).
Please install easy-to-use device for power off before installing wiring, which is for emergent
power off when necessary.
Please prevent the line cord from being trampled or pressed, especially the plug, power
socket and the junction from the device.
Note: Do not connect these two power supplying sources to the device at the same
time; it may result in device damage!
We assume no liability or responsibility for all the fires or electrical shock caused by
improper handling or installation.
We are not liable for any problems caused by unauthorized modification or attempted repair.
2．Environment
Please don’t aim the device at strong light (such as lighting, sunlight and so on) to focus;
otherwise it may cause overexposure (It is not the device malfunction), which will affect the
longevity of CCD or CMOS.
Please transport, use and store the device within the range of allowed humidity and
temperature.
Please don’t keep the device in a place which is wet, dusty, extremely hot, and extremely
cold and with strong electromagnetic radiation or unstable lighting.
Please do not allow water and other liquid falling into the camera in case that the internal
components are damaged.
Please do not allow rain or damp to the indoor device in case fire or lightning may occur.
Please keep the sound ventilation in case of heat accumulation.
Please pack the device with standard factory packaging or material with same quality when
transporting the device.
Heavy stress, violent vibration or water splash are not allowed during transportation, storage
and installation.
3. Operation and Daily Maintenance

2
Please do not touch the heat dissipation component of the device directly in order to avoid
scald.
Please do not dismantle the device; there is no component which can be fixed by users
themselves in the machine. It may cause water leakage or bad image for the device due to
unprofessional dismantling. Please contact after-sale service to replace desiccant if it
becomes green.
It is recommended to use the device with thunder proof device in order to improve thunder
proof effect.
The grounding holes of the product are recommended to be grounded to further enhance the
reliability of the camera.
Do not touch the CCD (CMOS) optic component directly. You can use the blower to clean
the dust or dirt on the lens surface. Please use a dry cloth wetted by alcohol to wipe away
the dust gently if it is necessary to clean.
Always use the dry soft cloth to clean the device. If there is too much dust, please use the
water to dilute the mild detergent first and then use it to clean the device. Finally use the dry
cloth to clean the device. Don’t use volatile solvent like alcohol, benzene, thinner and etc or
strong detergent with abrasiveness, otherwise it will damage the surface coating or reduce
the working performance of the device.
Dome cover is an optical device, please don’t touch or wipe cover surface directly during
installation and use, please refer to the following methods to deal with once dirt is found:
Stained with dirt
Use oil-free soft brush or hair dries to remove it gently.
Stained with grease or fingerprint
Use soft cloth to wipe the water drop or oil gently to make it dry, then use oil-free cotton cloth
or paper soaked with alcohol or detergent to wipe from the lens center to outward. It is ok to
change the cloth and wipe several times if it is not clean enough.
Warning
Please modify the default password after login in order to avoid being stolen.
Please use the standard accessories provided by manufacturer and make sure the device is
installed and fixed by professional engineers.
Please prevent the device surface from the radiation of laser beam when using laser beam
device.
Please do not provide two or more power supply modes for the device, otherwise it may
cause damage to the device.
Statement
Please refer to the actual product for more details; the manual is just for reference.
The manual will be regularly upgraded according to the product update; the upgraded
content will be added in the manual without prior announcement.

3
Please contact the supplier or customer service if there is any problem occurred when using
the device.
Please contact the customer service for the latest procedure and supplementary
documentation.
There may be deviation between the actual value of some data and the value provided in the
manual due to the reasons such as the real environment is not stable and so on. Please
refer to the company’s final explanation if there is any doubt or dispute.
The company is not liable for any loss caused by the operation which is not followed by the
manual.
FCC Information
1. FCC conditions：
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions:
This device may not cause harmful interference;
This device must accept any interference received, including interference that may cause
undesired operation.
2. FCC compliance：
This equipment has been tested and found to comply with the limits for a digital device, pursuant
to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference. This equipment generates uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communication. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV technician for help.
Note:
Please refer to the disk for more details, check and download corresponding user’s manual and
tool.
Before installation, please open the package and check all the components are included.
Contact your local retailer ASAP if something is broken in your package.
Accessory Name
Amount
Network Camera Unit
1
Installation Accessories bag
1
Quick Start Guide
1
CD
1

4
Table of Contents
1Device Structure...............................................................................................................5
1.1 Components........................................................................................................5
1.2 Dimensions..........................................................................................................7
2Installation.........................................................................................................................8
2.1 Device Installation..............................................................................................8
3Network Configuration...................................................................................................11
3.1 Modify IP Address............................................................................................11
3.2 Login WEB Interface........................................................................................13

5
1 Device Structure
1.1 Components
Note:
The following figures are for reference only, which are used to know the device component and
cable port function.
Device component and cable port function may differ according to different models, please refer
to the actual devices for details.
Figure 1-1

6
Figure 1-2
Please refer to the following sheet for detailed structure information.
Please refer to the following sheet for detailed port information.
Component
Component name
1
Device lens
2
X-Y-Z rotation module
3
Dome enclosure
Port
Port name
Function
4
MIC hole
Audio input
5
Network port
Connect to standard Ethernet
cable, provide PoE power supply
function.
6
Power input port
Connect to DC 12V power to input
power.
7
M12 mobile port
Connect to back-end device

7
1.2 Dimensions
Please refer to the following figure for the dimension information. The unit is mm. See Figure 1-3.
Figure 1-3

8
2 Installation
2.1 Device Installation
Note:
Please cut off the device power first when installing Micro SD card.
Please make sure the installation surface can at least sustain 3X weight of the camera and the
bracket.
Figure 2-1
Please refer to the steps listed below.
Step1
Use the inner hex wrench (provided) to loosen the three inner hexagon screws in the dome cover
and then open the cover.
Step 2
Install SD card
Note:
You need to implement this step if there is a Micro SD card slot and it needs to use Micro SD
card for the device.
Find the SD card slot location which is shown in Figure 2-2, open the upper cover, adjust the
direction of Micro SD card, insert the Micro SD card into the slot and make the upper cover back
in position.

9
Figure 2-2
Note:
Press the reset button for 10 seconds to realize device reset function.
Step 3
Take out the installation position map form the accessories bag; paste it on the installation
surface such as ceiling or wall according to the monitoring area.
Step 4
Draw and then dig three plastic expansion bolts holes on ceiling or other installation surface and
then insert three expansion bolts in the holes. Secure these three bolts firmly.
Note:
Please dig a “cable exit hole” on the surface according to the installation position map if you
want to pull out the cable from the top of the installation surface when installing cable.
You need to use the proper tool to open up the side port of the U-cable channel on the dome
enclosure if you want to pull out the cable from the side exit of the cable channel when you
are installing the device cable. And then you can pull out the cable from the side exit of cable
channel on the pedestal.
Step 5
Adjust the device installation pedestal to the proper position and then draw the cable through the
cable outlet you just dug on the installation surface. Align the “TOP”direction of the device with
the installation position map and then align the three screw fixing holes on the device pedestal
with the three plastic expansion bolt fixing holes on the installation surface. Put the three self-
tapping screws into the three plastic expansion bolts and secure them firmly, and then fix the
dome on the installation surface.
Step 6
Adjust device monitoring direction
Users can directly use hands to adjust the lens horizontally, it needs to use wrench to adjust lens
vertically, insert the wrench into the screw holes and move the wrench up and down to rotate the
lens vertically; it needs to use wrench to adjust image horizontally, insert the wrench into the
screw hole and move then wrench with 360°axis to make the image rotate.
Note:

10
The range of lens adjustment angle: vertical rotation direction (0°～+85°), image horizontal
rotation direction (0°～+355°), image rotation direction (0°～+360°).
Figure 2-3
Step 7
Hold the dome cover, align it with the cable exit location and make the cover back in position.
Then use inner hex wrench to fasten three inner hex locking screws to complete installation.
Step 8
Waterproof connector installation for network port (Optional); see Figure 2-4 for more details.
Note:
Please implement this step if the device is equipped with network port waterproof connector and
it is used outdoors.
Figure 2-4
1. Keep the convex groove outward and install the rubber ring into the network port, keep the
smaller hole of the rubber ring outward and install the fixing rubber ring into the main body of
the waterproof connector.
2. Pull the network cable without crystal head through main body of waterproof connector, fixing
rubber ring and waterproof locking cover, make the crystal head of network cable, and then
insert it into the network cable.
3. Put the main body of waterproof connector on the network port and rotate it clockwise to lock
the network port and waterproof connector firmly.
4. Put the waterproof locking cover on the main body of waterproof connector and rotate it
clockwise to lock the waterproof connector and waterproof locking cover firmly.

11
3 Network Configuration
The IP address of all the cameras is the same when leaving factory (default IP192.168.1.108), in
order to make the camera get access to the network smoothly, please plan the useable IP
segment reasonably according to the actual network environment.
3.1 Modify IP Address
IP address can be acquired and modified through quick configuration tool for the cameras which
are accessed via wired network, it needs to connect wired network to configure wireless
parameters before using wireless network cameras. In this chapter, it will introduce the approach
of modifying IP address via “Quick Configuration Tool”; also you can modify the IP address in the
network parameters of the WEB interface, please refer to the document in the disk << WEB
Operation Manual>> for more details.
Note:
Currently the quick configuration tool only supports the cameras which apply to the same
network segment with computer IP address.
Step 1
Double click the “ConfigTools.exe” and open the quick configuration tool.
Step 2
Double click the device to be configured; the system will pop out the “Login”dialog box. Enter the
IP address, user name, password and port number of the camera, and click “Confirm”.
Note:
The default user name and password are admin and admin respectively, the default of port is
37777. See Figure 3-1 for more details.

12
Figure 3-1
Step 3
Modify the camera IP address on the “Net”interface, click “Save”to finish modification.
See Figure 3-2 for more details.
Figure 3-2

13
3.2 Login WEB Interface
Note:
Different devices may have different WEB interfaces, the figures below are just for reference,
please refer to the document <<WEB Operation Manual>> in the disk and the actual interface for
more details
Step 1
Open IE and input the modified camera IP address in the address bar.
Step 2
The login interface is shown below; please input your user name and password (Default user
name is admin and password is admin respectively), click “login”.
See Figure 3-3 for more details.
Figure 3-3
Step 3
Install controls according to the system prompt; see Figure 3-4 for the WEB main interface.
Please modify the administrator password as soon as possible after you successfully logged in.

14
Figure 3-4
Note
This quick start guide is for reference only. Slight difference may be found in the
user interface.
All the designs and software here are subject to change without prior written
notice.
If there is any uncertainty or controversy, please refer to the final explanation of us.
Please visit our website or contact your local service engineer for more
information.
Zhejiang Dahua Vision Technology Co., Ltd
Address：No.1199 Bin’an Road, Binjiang District, Hangzhou, PRC.
Postcode: 310053
Tel: [phone]
Fax: [phone]
Email:[e-mail]
Website: www.dahuasecurity.com