Dahua K Series User manual

Dahua K Series Cube Network Camera Quick Start Guide
V 1.0.0
Dahua Technolog CO., LTD

1. Packing List
Device × 1 QSG ×1
Power Adapter ×1 Screw Package ×1
Installation Position Map ×1
2

2. Product Appearance
Figure 2-1 Figure 2-2
Figure 2-3
Please re er to the ollowing sheet or more details about each port.
SN Name
1 Network port
2 Reset/WPS button
3 Digital input/output
4 Power port
5 Built-in speaker
6 Micro SD card slot
7 Indicator light
3

SN Name
8 Built-in MIC
9 IR LED
10 PIR
Sheet 2-1
Note:
For reset, long press or 8 seconds and then the light o ; For WPS, one quick press.
Please re er to the ollowing sheet or more details about status o indicator light.
Indicator light status Device status
Red light normally on Booting
Green light slow lashing Booting completed, await wi i con ig, enter smart
con ig status;
Green light quick lashing Wi i smart con ig in progress, including WPS,
management rame and etc.
Green light normally on Wi i connection succeeded, operate normally.
Red and green lights lash
alternately
Device upgrade
Red light slow lashing Network connection ailure or disconnection a ter
network connection success.
Red light quick lashing Device mal unction, ail to boot up; alarm or SD card
mal unction
Sheet 2-2
4

3. Operate b Eas 4ip APP
1. Power on the device with power adapter.
2. Connect your smart phone to your WiFi network. Scan the “Easy4ip APP” QR on the packing box,
download and install the Easy4ip APP.
3. Open Easy4ip APP (take IOS as an example), tap login to login the APP, see Figure 3-1.
Figure 3-1
4. Tap “register” or irst use.
5

Figure 3-2
5. Tap “+” to add devices.
Figure 3-3
6. Choose “Wireless”.
6

Figure 3-4
7. Name the camera and scan the QR code on camera.
Figure 3-5
7

8. Input the Wi-Fi password.
Figure 3-6
9. Waiting or 60s to inish the Wi-Fi connection.
8

Figure 3-7
Note: I you want to change the Wi-Fi signal, please reset the camera to actory de ault and repeat
step 6-9;
Figure 3-8
9

4. Operate b DMSS APP
Step 1
Power on the camera.
Step 2
Connect iphone to a WiFi signal.
Step 3
Open DMSS (downloaded rom APP Store), choose Device Manager.
Figure 4-1
Step 4
Click “+”.
Figure 4-2
Step 5
Choose “WiFi con iguration”.
10

Figure 4-3
Step 6
Input a device name and scan the QR code on camera, then “next”.
Figure 4-4
Step 7
Input the WiFi password, then “next”.
11

Figure 4-5
Step 8
Connection succeeds.
Figure 4-6 Figure 4-7 Figure 4-8
Note:
Please try again or check the WiFi password i it ailed.
The WiFi con iguration will be closed i activating WPS unction, Please reset the device i you still
need to con igure WiFi via DMSS App.
12

13

5. Device Installation
Important
Please make sure the installation surface can min support the 3X weight of the camera and the
bracket.
Figure 5-1
Step 1
Paste the installation map on the installation sur ace such as wall, ceiling or the wood.
Step 2
Dig holes in the installation sur ace according to the installation map.
Step 3
Insert the expansion bolts rom the accessories bag to the holes you just dug. I it is the wood sur ace
you can skip to the next step.
Step 4
Fix the device with screw in the accessories bag.
Step 5
Connect the cable and then boot up the device.
Step 6
Loosen the adjust knob or a little bit, adjust the camera to proper surveillance position according to
your practical requirements.
Step 7
Secure the knob o the bracket to ix the camera.
Note:
This quick start guide is for reference onl . Slight difference ma be found in user
interface.
All the designs and software here are subject to change without prior written notice.
All trademarks and registered trademarks mentioned are the properties of their respective
owners.
14

If there is an uncertaint or controvers , please refer to the final explanation of us.
Please visit our website or contact our local service engineer for more information.
Dahua Technolog Co., Ltd
Address：No.1199 Bin’an Road, Binjiang District, Hangzhou, PRC.
Postcode: 310053
Tel: [phone]
Fax: [phone]
Email:[email protected]
Website: www.dahuasecurity.com
15