Daikin R13LV2S User manual

REMOVAL
PROCEDURE
SERVICE MANUAL
3.5 kW Class
13000 Btu/h Class
Outdoor Unit
Non-Inverter
Pair Type
Si011184

Service Manual
Removal Procedure
Outdoor Unit
Applicable Models
zCooling Only
R13LV2S
AR13KV2S
R35HV1
R35HV14
R35JV1V
R35MV16

Si011184
Removal Procedure 1
Table of Contents
1. Removal of Outer Panels / Fan Motor (Pattern 1)...................................2
2. Removal of Outer Panels / Fan Motor (Pattern 2).................................10
3. Removal of Electrical Component ASSY (Pattern 1) ............................18
4. Removal of Electrical Component ASSY (Pattern 2) ............................19
5. Removal of Sound Blankets..................................................................20
6. Removal of Capillary Tube (Pattern 1)..................................................21
7. Removal of Capillary Tube (Pattern 2)..................................................22
8. Removal of Compressor ASSY.............................................................23
Note: The illustrations may be slightly different depending on the model.

Removal of Outer Panels / Fan Motor (Pattern 1) Si011184
2Removal Procedure
1. Removal of Outer Panels / Fan Motor (Pattern 1)
Procedure Warning Be sure to wait for 10 minutes or more after turning off all power
supplies before disassembling work.
Step Procedure Points
1. Appearance features
Take care not to cut your
finger by the fins of the
outdoor heat exchanger.
2. Remove the panels.
The stop valve cover is
united with the shield plate.
When reassembling, make
sure to fit the 5 hooks.
1Remove the screw of
the stop valve cover.
Pull down the stop
valve cover and remove
it.
(R15226)
(R16332)
Stop
valve
cover
(R7188)
Shield plate
Hook
(R16333)

Si011184 Removal of Outer Panels / Fan Motor (Pattern 1)
Removal Procedure 3
2Remove the 3 screws
and remove the top
panel.
3Remove the 4 screws
and remove the
discharge grille.
The discharge grille has 4
hooks.
Step Procedure Points
Top panel
(R16334)
(R16335)
(R16336)

Removal of Outer Panels / Fan Motor (Pattern 1) Si011184
4Removal Procedure
4Remove the 8 screws
of the front panel.
5Unfasten the hooks.
Pull and remove the
front panel.
The front panel has 4 hooks.
Step Procedure Points
(R16337)
Front panel
Hook
(R16338)

Si011184 Removal of Outer Panels / Fan Motor (Pattern 1)
Removal Procedure 5
3. Remove the fan motor. Nut size: M6
1Remove the nut of the
outdoor fan.
2Remove the outdoor
fan.
Align the mark of the
outdoor fan with the D-cut
section of the motor shaft
when reassembling.
3Pull out the 2 terminals
(red, white) from the fan
capacitor (C2R).
4Pull out the terminal
(black) from K1M (5).
5Release the fan motor
lead wire from the hook.
Step Procedure Points
(R15230)
Outdoor fan
10 mm
(R17447)
D-cut
(R7197)
(R17457)
to fan motor:
white
to fan motor:
red
C2R
2
4
6
14
A2
1
3
5
13
A1
K1M
to fan motor:
black
(R16562)

Removal of Outer Panels / Fan Motor (Pattern 1) Si011184
6Removal Procedure
6Remove the screw and
remove the fan motor
fixing frame.
Put the fan motor lead wire
through the back of the fan
motor when reassembling so
as not to be entangled with
the outdoor fan.
When reassembling, fit the
lower hooks into the bottom
frame.
Step Procedure Points
(R15232)
Fan motor fixing frame
(R15233)
(R3249)
Lead wire Outdoor fan
(R7206)

Si011184 Removal of Outer Panels / Fan Motor (Pattern 1)
Removal Procedure 7
7Release the fan motor
lead wire from the
hooks.
8Remove the 4 screws
and remove the fan
motor.
Step Procedure Points
(R15234)
(R15235)
Fan
motor

Removal of Outer Panels / Fan Motor (Pattern 1) Si011184
8Removal Procedure
4. Remove the right side
panel.
1Remove the 7 screws
on the terminal board
and disconnect the
connecting wire and the
power supply wire.
2Remove the screw and
remove the wire clamp.
3Lift up and remove the
guard net.
4Remove the 2 screws
on the rear side.
Step Procedure Points
Connecting
wire
Power supply
wire
Wire clamp
(R16537)
Terminal board
Guard net
(R8284)
(R15237)