Dakota Alert hm-01 User manual

The Mightylite oodlight is an energy ecient,
high-powered outdoor LED oodlight.
The oodlight is suitable for installation on most
walls in a range of locations including entrances,
gardens, garages and outdoor parking areas.
IMPORTANT SAFETY INSTRUCTIONS
This product should only be installed by a competent
individual who is familiar with all applicable codes and/
or regulations that may apply to the installation of this
product. In certain jurisdictions this product needs to
be installed by a licensed electrician.
Please follow these instructions carefully before
attempting to install and operate this light.
The risk of electric shock should be minimized by the
installation of appropriate safety devices including the
incorporation of a GFCI (Ground Fault Circuit Interrupt).
Cables should always be protected against short circuit
and overload.
Ensure the voltage marked on the product is the same
as the electrical power supply to be used.
DO NOT position the light near ammable, combustible
or explosive liquids, solids, gases or equipment.
DO NOT direct the light into a person’s eyes. The light
output is very intense and if used incorrectly could
cause eye damage.
ALWAYS maintain the light in good condition, with
repairs undertaken only by a qualied electrician.
PARTS INCLUDED
1 x Mightylite LED Floodlight
1 x Connection box
1 x Cable gland
1x “C” bracket
2 x screw knobs
4 x Connection box screws
4 x Connection box screw covers
4 x Connection box mounting screws
4 x Connection box mounting screw covers
CHOOSING A
MOUNTING LOCATION
Mount the oodlight onto a solid
structure, 10-15ft above the
ground (Fig. 1)
32556 E Main St
Elk Point, SD 57025
ph: 605.356.2772
fax: [phone]
www.DakotaAlert.com
Dakota Alert®
WIRELESS SECURITY EQUIPMENT
Hylite Mightylite™
FIG 1
hm-01

If feeding a wire through the knock-out at the back of
connection box, use silicone sealant to completely seal
between the back of the connection box and wall sur-
face to prevent water from seeping into the connec-
tion box. The silicone sealant should be waterproof &
UV proof. If feeding a wire through a knock-out on the
side of the connection box the sealing gland should
be used and installed as shown in
Fig. 5. Once the sealing gland is
installed the nut should be gently
tightened up against the gland
body to ensure the wire is secured
in place and no water can get into
the connection box.
Feed the A/C cable into the
connection box and strip
approximately 1/4” of insulation
from each of the 2 conductors of
the A/C wire and attached to the
terminal block as shown in Fig.
6, black wire to black (hot) white
wire to white (neutral).
Make sure the waterproof seal to
the lid is in place (Fig. 7) and fasten
to the connection box using the 4
connection screws provided. In-
stall the provided screw covers. To
adjust the Mightylite simply hold
the connection box rmly while
moving the head of the oodlight
to the required position. If using
the “C” bracket, the junction box
can be swiveled to the desired
position and then the light head
can be further swiveled.
GLAND
FIG 5
FIG 6
GLAND
FIG 7
INSTALLATION AND WIRING INSTRUCTIONS
Warning: Isolate the power supply before installation
and turn o the A/C power to the circuit.
The unit requires connection to a 120V 60Hz power
supply. It is recommended that the unit is connected to
the domestic lighting circuit using 2 conductor round
exible cable of 14 AWG. If the cable is used outdoors,
you must use waterproof cable. It is also advisable to
install a single pole wall switch to allow easy control of
the oodlight.
Position the unit on the wall and mark the position
for the connection box (which can be positioned
horizontal or vertical (Fig. 2, 3)
Ensure the wires can easily
enter the connection box
through either the knock-
out (KO) at the back of the
connection box, or through
those at the sides (Fig. 4)
Mark the 4 drill holes required to secure the box to the
wall (and mark the cable outlet location if required). Or
use the “C” bracket to mount to a wall. If using the “C”
bracket, use the knockouts on the side of the box to
attach the bracket with the screw knobs
Drill the wall and screw the connection box onto the
wall using the screws provided. Or mount the “C”
bracket to the wall using two screws. Once the screws
are attached, the screw covers (provided) should be
used to stop any water ingress through the mounting
holes.
FIG 3
VERTICAL
FIG 2
HORIZONTAL
THIS END UP
FIG 4 KO