Daktronics SMALL MATRIX GALAXY GS6 Series User manual

201 Daktronics Drive
Brookings, SD 57006-5128
www.daktronics.com/support
800.325.8766
SMALL MATRIX
GALAXY®GS6 SERIES
INSTALLATION AND
OPERATION MANUAL
P1817
DD3125362
Rev 13
22 April 2022

Copyright © 2022
All rights reserved. While every precaution has been taken in the preparation of this manual, the publisher assumes no
responsibility for errors or omissions. No part of this book covered by the copyrights hereon may be reproduced or copied
in any form or by any means—graphic, electronic, or mechanical, including photocopying, taping, or information
storage and retrieval systems—without written permission of the publisher.
Daktronics trademarks are property of Daktronics, Inc. All other trademarks are property of their respective companies.
FCC Statement
Supplier Declaration of Conformity (SDoC)
This product complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired
operation.
Note: This equipment has been tested and found to
comply with the limits for a Class A digital device,
pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference when the equipment is operated
in a commercial environment. This equipment
generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance
with the instruction manual, may cause harmful
interference to radio communications. Operation of
this equipment in a residential area is likely to cause
harmful interference in which case the user will be
required to correct the interference at their own
expense.
Warning: The user is cautioned that changes and
modications made to the equipment without the
approval of manufacturer could void the user’s
authority to operate this equipment.
Industry Canada Regulatory Information
This Class A digital apparatus complies with Canadian
ICES-003.
Cet appareil numérique de la classe A est conforme à
la norme NMB-003 du Canada.
Inquiries
Contact Daktronics with any questions regarding our
product compliance.
Mail:
Daktronics
201 Daktronics Dr.
Brookings, SD 57006 USA
Phone:
800-325-8766
Website:
www.daktronics.com

– i –
Table of Contents
1 Introduction�����������������������������������������1
Limitation of Liability ..................................1
Contact Information .................................1
Model Number Guide...............................1
2 Installation Preparation ����������������������2
Pre-Installation Checklist ...........................2
Structure Requirements.............................2
3 Display Installation �����������������������������3
Display Installation Preparation................3
Display Installation .....................................3
4 Electrical Installation ��������������������������4
Warnings and Disclaimers ........................4
Power Requirements .................................4
Main Disconnect .......................................4
Conduit.......................................................5
Overview of Power/Signal Connection ..5
Earth Ground Installation ..........................5
Important Points About Grounding .........6
Power Connection ....................................6
Displays With an External Power
Termination J-box�����������������������������������6
Displays With Internal Power
Termination����������������������������������������������7
5 Signal Cable Installation ��������������������8
Primary/Mirror Display Interconnections .8
6 System Start-Up Procedure����������������9
Boot Sequence..........................................9
Start-Up Checklist ......................................9
7 Network and Communication
Installation �����������������������������������������10
Network and Communication
Installation Recommendations ..............10
Requirements For Communication
Through A Network .................................10
Connect A Display to A DHCP Network
...................................................................10
Display Currently Congured For DHCP
(Default)�������������������������������������������������10
Network Requirements .....................10
Installation/Start-up Steps.................10
Display Congured For Static IP
Address��������������������������������������������������10
Network Requirements .....................11
Conguration Steps Using IP Address
.............................................................11
Conguration Using DisplayFind To
Discover The Display ����������������������������12
Download DisplayFind......................12
Launch DisplayFind...........................12
Connect To A Display.......................13
Connect A Display To A Static IP Network
...................................................................14
Display Currently Congured for DHCP
(Default)�������������������������������������������������14
Network Requirements .....................14
Conguration Steps Using IP Address
.............................................................14
Display Congured For Static IP
Address��������������������������������������������������15
Network Requirements .....................15
Conguration Steps Using IP Address
.............................................................15
8 Venus Software Conguration���������17
First-Time Venus Login..............................17
Logging In–Daktronics Web-Hosted
Server�����������������������������������������������������17
Logging In–Customer Local-Hosted
Server�����������������������������������������������������17
Venus Menu Overview............................18
Venus System Setup ................................18
Contact Information and Where to Get
Help ...........................................................19
Telephone ..........................................19
Online .................................................19
9 Display Maintenance�����������������������20
Internal Display Access ...........................20
Ventilation System ...................................21
Display Face Cleaning............................21
Wet Cleaning Process ��������������������������21
Dry Cleaning Process���������������������������22
10 Display Troubleshooting�������������������23
Power and Signal Routing ......................23
Power Routing ���������������������������������������23
Signal Routing ���������������������������������������24
Controller Diagnostics .............................25
Module Diagnostics.................................25
Module Self-Test.......................................25

– ii –
Table of Contents
11 Replacing Parts���������������������������������26
Module Replacement.............................26
Power Supply Replacement ..................26
Controller Replacement.........................27
12 Daktronics Exchange and Repair &
Return Programs��������������������������������28
Daktronics Exchange and Repair &
Return Programs ......................................28
Exchange Program ������������������������������28
Before Contacting Daktronics�������������28
Repair & Return Program ���������������������29
Shipping Address����������������������������������29
Daktronics Warranty and Limitation of
Liability ......................................................29
A Reference Drawings �������������������������31
B Daktronics Warranty and Limitation
of Liability�������������������������������������������33
C Legacy Remote Display
Conguration ������������������������������������35
Connect A Display to A DHCP Network
...................................................................35
Display Currently Congured for DHCP
(Default)�������������������������������������������������35
Network Requirements .....................35
Installation/Start-up Steps.................35
Display Congured For Static IP
Address��������������������������������������������������35
Network Requirements .....................35
Conguration Steps Using IP Address
.............................................................35
Installation/Start-up Steps.................35
Display Congured For Static IP
Address��������������������������������������������������35
Network Requirements .....................35
Conguration Steps Using IP Address
.............................................................36
Conguration Using DisplayFind To
Discover The Display ����������������������������37
Download DisplayFind......................37
Launch DisplayFind...........................37
Connect To A Display.......................38
Connect A Display To A Static IP Network
...................................................................39
Display Currently Congured for DHCP
(Default)�������������������������������������������������39
Network Requirements .....................39
Conguration Steps Using IP Address
.............................................................39
Display Congured For Static IP
Address��������������������������������������������������40
Network Requirements .....................40
Conguration Steps Using IP Address
.............................................................40

Introduction
1
1 Introduction
This manual provides the necessary information to install and service a Galaxy®Small
Matrix GS6 series display.
Please read and understand all steps in this manual before beginning the installation
process.
Complete the steps in this manual in order. Contact Daktronics Technical Support with
any questions before or during the installation process.
Limitation of Liability
The factory warranty will be void if:
• The display is not installed according to the steps in this manual.
• Proper electrical service is not provided or the display is not grounded properly.
• Unauthorized modications are made to the display, display cabinet, or the control
system.
Refer to Daktronics Warranty and Limitation of Liability (p�33) at the end of this manual
for the full Daktronics Warranty and Limitation of Liability.
Contact Information
For assistance before, during, or after display installation, please contact Daktronics
Technical Support: 1-800-DAK-TRON (325-8766).
Model Number Guide
Galaxy® Small Matrix GS6 model numbers are dened as follows:
GS6-RxC-M-RGB-F
GS6 = Outdoor Standard Galaxy®display
R= Number of pixel rows high
C= Number of pixel columns wide
M= Pixel pitch in millimeters
RGB = LED Color: RGB (Red, Green, Blue)
F= Face setup: SF – Single Face or 2V – Primary/Mirror
Displays are either single face (SF) or two view (2V). In 2V units, the rst display is referred
to as the primary and the second is called the mirror. If the second display is mounted
more than 8' (2.4 m) from the primary display, two primary displays are used.

Installation Preparation
2
2 Installation Preparation
This section explains what to consider before installing a Galaxy®Small Matrix GS6 display.
Follow all guidelines and safety precautions in this manual when installing the display. Do
not modify the display or control system in any manner without the written permission of
Daktronics engineering staff.
Any unauthorized modications void the display warranty.
Pre-Installation Checklist
• The display was not damaged during shipping.
• The mounting structure will provide a straight and square mounting frame for the
display.
• The support structure must be able to carry the weight of the display and meets local
and national codes.
• Ensure proper power is available at sign structure, refer to the Shop Drawing for
display power requirements.
• The display cabinet has no holes (accidental or intentional) that will allow water to
enter the display.
• All display modules are fully latched into the display cabinet.
Structure Requirements
Support structure design depends on mounting method, installation height, display size,
and weight. Because every installation site is unique, Daktronics approves no single
procedure for mounting displays.
Things to consider prior to installation:
• Display structure and mounting must not obstruct airow–refer to the Shop Drawing
for ventilation space requirements.
• The light sensor must not be obstructed for the display to function properly.
For additional questions about display mounting requirements and specications, refer
to the display Shop Drawing or contact Daktronics Technical Support at 1-800-DAK-TRON
(325-8766)

Display Installation
3
3 Display Installation
This section explains the steps necessary for proper lifting and installation of the display to
the sign structure.
Follow all guidelines and safety precautions in this manual when installing the display.
Do not modify the display or control system in any manner without the written permission
of Daktronics engineering staff. Any unauthorized modications will nullify the warranty.
Display Installation Preparation
• Inspect the display for damage prior to installation.
• Use all clip angle locations for mounting.
• Provide an adequate support structure that is straight and level.
• Provide adequate ventilation that meets or exceeds display specications listed on
the Shop Drawing�
• Use all lift eyes when lifting the display.
• Do not open the DMP enclosure.
• Do not drill holes into the display unless noted.
• Do not block display ventilation system.
• Do not use the lift eyes for display mounting.
Display Installation
1� Carefully remove shipping crate.
2� Attach a crane or lift truck to the lift eyes on the display's top.
Note: Use a spreader beam to ensure proper vertical lift that will not damage the
cabinet. Refer to Figure 1.
3� Lift the display off the truck to the display
structure.
Note: Do not lift displays in wind speeds
greater than 20 mph (32 kph).
4� Mount the display to the structure by welding
or bolting all clip angle locations to horizontal
stringers.
Note: Use all clip angles when mounting the
display.
5� Remove crane support and tag lines from the display once mounting is complete.
Use Lift Bar and ALL Lift Eyes
Figure 1: Proper Display Lifting

Electrical Installation
4
4 Electrical Installation
This section explains the steps necessary to make nal electrical connections to the
display from the primary power source. For display-specic power requirements, refer to
the Shop Drawing or label on the rear of the display. Follow all installation guidelines.
Warnings and Disclaimers
• Ensure that all electrical work meets or exceeds all local or national electrical codes.
• Provide the required power to the display as listed on the product labels,
specications, or site-specic riser drawings. The conductor size may vary based on
the length of the power run.
• Consider implementing a separate circuit for the display using an isolation
transformer or dedicated transformer.
• Daktronics assumes no liability for any issues caused by line voltage uctuations or
other improper power conditions.
Important Notes
• Qualied personnel must perform electrical installations to prevent injury to personnel
and damage to the equipment.
• Daktronics engineering staff must approve any changes made to the display. Before
altering the display, submit detailed drawings for the proposed modications to the
Daktronics engineering staff for evaluation and approval, or the warranty will be void.
• Improper installation could result in serious damage to the equipment and could be
hazardous to personnel.
• Size conductors of circuits that deliver power to the display according to national
and local electrical codes so the power distribution system delivers full-load power to
the display while maintaining a voltage within 5% of the utility nominal voltage.
Power Requirements
• Install the display according to all applicable local and national electrical codes. This
includes proper grounding and bonding of the display.
• Do not connect the display to any voltage other than that listed on the Daktronics
product label.
• Displays use single-phase power. Proper power installation is imperative for display
operation.
Main Disconnect
Daktronics requires using a power disconnect switch with the display. A disconnect allows
all ungrounded conductors to be disconnected near the point of power connection.
Locate the disconnecting means either in a direct line of sight from the display or so it
can be locked in the open position. This ensures that power is not reconnected while
service personnel work on the display.

Electrical Installation
5
Conduit
Daktronics does not provide conduit. Separate conduit must be used to route:
• Power
• Signal IN wires to the signal termination enclosure (when applicable)
• Signal OUT wires (if not using the provided interconnect cable)
For power, displays have either a J-box or a 3/4" conduit access hole located in the
lower-right corner on the rear of the display. For signal, displays have signal input quick
connects or etched drilling guides for conduit.
Overview of Power/Signal Connection
Power to the display is terminated externally in most cases. Power Connection (p�6)
shows external wiring examples.
Possible methods for signal termination are shown in the various communication
manuals.
1� Power is routed to the display through a fused disconnect switch capable of opening
all ungrounded power conductors. Install the disconnect within the line of sight of
any personnel performing maintenance on the display, unless it can be locked in the
open position.
2� Route power conductors from the disconnect to the display through conduit
following local code specications.
3� Terminate display power either to the J-box or internally at the power termination
panel.
4� Connect the grounding conductor to the grounding lug on the rear of the display.
5� Route signal cable to the signal termination enclosure. Ground the enclosure to an
isolated earth-ground connector (when required).
6� Route signal into the enclosure through conduit. The knockouts on the enclosure
require the use of 3/4" conduit.
7� Route signal quick-connect cables from the enclosure to the display either through
conduit or through the display pole if power is not also routed in the display pole.
Note: Quick-connect cables MUST be secured to protect them from weather or
vandalism.
Earth Ground Installation
To connect the Galaxy®Small Matrix GS6
display to an earth-ground electrode,
follow these steps.
1� Install an earth-ground electrode
(ground rod, ground plate, etc.)
near the base of the display. Refer to
Figure 2 for guidelines.
Note: Each display face requires an
earth-ground electrode.
Primary
Mirror
Display
Ground Lug
Thermal Weld
Connection
Preferred Conduit
Copper Ground Conductor
(One Per Display Face)
Copper Ground Rods
8 ft.(2.5 m)
min.
8 ft.(2.5 m)
min.
Figure 2: Proper Display Grounding

Electrical Installation
6
2� Connect a copper wire from the grounding electrode to the ground lug on the rear
of the display.
3� Bury any copper cable or grounding electrodes so they are below grade.
Important Points About Grounding
All components of a display system—including but not limited to displays, control
equipment, and connected peripheral equipment—must be electrically grounded.
Only qualied individuals may perform electrical work, including verication of ground
resistance. Daktronics is not responsible for improper grounding or damage incurred as a
result of improper grounding.
Grounding methods must meet the provisions of all applicable local and national codes.
Inspect and verify all grounding methods meet the provisions of all applicable local and
national codes.
Proper grounding is necessary for reliable equipment operation and general electrical
safety. Failure to properly ground the display system may void the warranty, disrupt
operation, damage equipment, and cause bodily harm or death.
Power Connection
Power is most often terminated to the J-box on displays. However, larger displays require
power to be terminated internally in the Power Termination Panel.
Displays With an External Power Termination J-box
To terminate hot, neutral, and ground wires at the
J-box, follow these steps:
1� Route the power cable through conduit to the
rear of the display and into the power
termination J-box [the J-box contains 3/4"
threaded conduit tting(s)].
Note: The J-box contains two or three wires
plus a ground coming from the power
termination panel inside the display.
2� Inside the J-box, connect the power wires to
the wires coming from the display interior using
wire nuts. Refer to Figure 3 for 120 VAC and
Figure 4 for 120/240 VAC.
The following colors are used for the pre-
terminated wires:
120 VAC 120/240 VAC
Line 1 – Black
Line 1 – Black
Line 2 – Red
Neutral – White Neutral – White
Ground – Green/Yellow Ground – Green/Yellow
120 V Termination
(Box with Cover Removed)
Wiring from power termination
panel inside display
Line 1 – Black
Neutral – White
Ground – Green/Yellow
Figure 3: 120 V J-box Termination
120/240 VAC Termination
(Box with Cover Removed)
Wiring from power termination
panel inside display
Line 1 – Black
Line 2 – Red
Neutral – White
Ground –
Green/Yellow
Figure 4: 120/240 V J-box Termination

Electrical Installation
7
Displays With Internal Power Termination
To terminate single-phase power
to the internal power termination
panel, complete these steps:
1� Open the display as explained
in Internal Display Access
(p�20) and locate the power
termination panel.
2� Route the cable through
conduit to the rear of the
display. Use the 3/4" knockout
for access, being careful not to
damage internal components.
3� Connect the neutral wire to the
neutral lug and the live wires to
the Line 1 and Line 2 lugs.
4� The ground wire connects to
the grounding bus bar. Refer to
Figure 5 for an example.
CB1
15
CB2
15
CB3
15
CB4
15
Z1 Top
Z2 Bottom
LINE
LOAD
Z3 Top
Z4 Bottom
LINE
LOAD
Four Breaker Connections
• White Neutral Wiring
(Z1 Load to Pin 1 of J41)
• White Neutral Wiring
(Z2 Load to Pin 1 of J42)
• White Neutral Wiring
(Z3 Load to Pin 1 of J43)
• White Neutral Wiring
(Z4 Load to Pin 1 of J44)
Green Ground Wiring
(Ground Bar to Pin 3 of J41)
(Ground Bar to Pin 3 of J42)
(Ground Bar to Pin 3 of J43)
(Ground Bar to Pin 3 of J44)
• Black Line Wiring
(Z1 Load to Pin 2 of J41)
• Black Line Wiring
(Z2 Load to Pin 2 of J42)
• Black Line Wiring
(Z3 Load to Pin 2 of J43)
• Black Line Wiring
(Z4 Load to Pin 2 of J44)
Mount Z1 On Top of Z2
and Z3 On Top of Z4
White Neutral Wiring
(Terminal Neutral Block
to Z1, Z2, Z3, and Z4 Line)
Black Line Wiring
(CB1 to Z1 Line
and CB2 to Z2 Line)
Black Line Wiring
(CB3 to Z3 Line
and CB4 to Z4 Line)
LINE 2
NEUT.
LINE 1
Strain Relief
Figure 5: Single-phase Four Breaker Domestic Panel

Signal Cable Installation
8
5 Signal Cable Installation
For specic details on installing the communications, consult the quick guide and manual
included with the communication equipment. Each type of communication is listed
below with its document number.
These are the standard communication types, but each site is unique and may include
additional equipment. If problems arise, contact the display's service company or
Daktronics Customer Service.
Communication Type Communication Manual Communication Quick Guide
Wireless Ethernet Bridge DD1685027 DD1417586
Ethernet DD1417609 DD1417573
Fiber Ethernet DD1417611 DD1417581
Primary/Mirror Display Interconnections
If this display is a two-sided primary/mirror display, two
quick-connect cables are provided to connect the signal
between the two faces. Refer to Figure 6 for an example.
1� Connect a cable from the Signal Out jack on primary
face to Signal In jack on mirror face.
2� Connect a second cable from the Signal Out jack
on the mirror face to the Signal In jack on the primary
face.
3� Secure the excess cable to the support structure to
prevent damage from weather or vandalism.
Figure 6: Primary/Mirror Quick-
connect Cable

System Start-Up Procedure
9
6 System Start-Up Procedure
Displays show a boot sequence about two minutes after power is turned on. This
information is very useful when conguring the display in Venus®software. Prior to turning
the display on, make sure display communications and any network connections have
been made.
Boot Sequence
Description
Firmware Name and Version
Display Size (Pixels High by Pixels Wide)
DHCP Name Assigned
IP Address and State
MAC Address
Conguration Port
Status Port
Management Port (Used to Access Conguration)
Description
Start-Up Checklist
• Conrm power is correctly connected to the display.
• Conrm there is sufcient power according to display requirements.
• Conrm a main disconnect is installed.
• Conrm the display is grounded per local and national codes.
• Conrm that all communication equipment is installed according to provided
documentation.
• Conrm that any necessary network connections have been made.
• Conrm ability to log in to venus�daktronics�com
• Inspect peripheral equipment (temperature sensor, light sensor, etc.) for proper
installation.

Network and Communication Installation
10
7 Network and Communication Installation
This section explains how to set up communications with a Galaxy®Small Matrix GS6
display through a network or an individual computer. Refer to the available standard
communication options in the provided quick guides and reference manuals for more
information.
Daktronics is not responsible for setting up a customer's network system, neither a Local
Area Network (LAN) ror a Wide Area Network (WAN).
See Legacy Remote Display Conguration (p.35) for legacy display conguration.
Network and Communication Installation
Recommendations
• Complete all network and communication installation prior to turning on the display.
• Have a laptop on site with Internet access (preferred).
• Work with the customer's IT professional for network integration.
Galaxy®Small Matrix GS6 displays use DHCP by default, which allows automatic display
conguration by the customer's network, and eliminates manual conguration of the
player.
When the display is connected to a network that supports DHCP, a default DHCP name
similar to “DMP8.xx.xxxx” or “DMP5.xx.xxxx”, where “xxxx” represents a unique identier for
the display, is shown in the display boot sequence.
Requirements For Communication Through A Network
The display must be allowed to establish an outgoing internet connection on Port 80
(http) and Port 443 (https).
Connect A Display to A DHCP Network
Display Currently Congured For DHCP (Default)
The following steps explain how to congure a display and connect to a network that
supports DHCP. Using the display's DHCP name is desired for communication.
Network Requirements
• DHCP Server
• Existing Network
• Available network port, congured properly
Installation/Start-up Steps
1� Ensure the display has an established link with the network.
2� Turn on the display.
Display Congured For Static IP Address
The following steps explain how to recongure a display for DHCP network when it has
previously been congured for a static IP address.

Network and Communication Installation
11
Network Requirements
• Existing Network
• Available network port, congured properly
• PC
• Internet web browser
Conguration Steps Using IP Address
1� Connect a computer to the display.
2� Turn on the display.
3� Observe boot sequence–recongure computer to the same IP address range as the
display and same subnet.
4� Manually enter display IP address in web browser followed by :85 (for example,
http://169.254.13.87:85) to identify the correct connection port.
5� Enter Dak as the username and DakPassword! as the password in the Windows
Security window.
6� Click OK to connect to the display (refer to the help le for additional information
about the conguration utility).
7� Click the Network tile.
8� Click Automatic under both the IP and DNS Conguration headings.

Network and Communication Installation
12
9� Click Save.
10� Log out of the conguration utility.
11� Turn off the display.
12� Disconnect the computer from the display and connect display to the network.
13� Ensure the display has an established link with the network.
14� Turn on the display.
Conguration Using DisplayFind To Discover The Display
Download DisplayFind
1� Open Internet Explorer or Firefox web browser.
2� Navigate to dakles.daktronics.com
3� Click Venus 1500 > Utils > DisplayFind > DisplayFind.exe.
4� When prompted, select Run to complete the installation of the DisplayFind utility or
Save to the computer for later use.
Launch DisplayFind
Double-click the DisplayFind icon on your desktop.
Each item listed at the top of the DisplayFind utility should have a green check mark.
Refer to the explanations below for what each item means. If an item has a red X next to
it, click it for additional information or to access the download.
The Current User Is An Administrative User On This Computer
• The user must have administrative rights to install SilverlightTM.
• Once SilverlightTM is installed, administrative rights are not necessary.
Windows Firewall Exception Is Currently Enabled
• Windows rewall should be temporarily disabled to allow discovery responses to be
received from any displays.
• Other third party Antivirus/rewall applications (McAffee, Symantec, ZoneAlarm, etc.)
should also be temporarily disabled.
SilverlightTM Version – A green checkmark tells you SilverlightTM 3.0 or newer is installed.

Network and Communication Installation
13
Connect To A Display
1� Select the Network Adapter used to communicate with your display.
2� Click the Find Displays button to detect any displays using the selected network
adapter.
3� Detected displays are listed in the bottom window of the utility.
4� Click the desired display (VIP5-xx-xxx) to launch the conguration utility within your
web browser.
Note: Refer to the conguration utility help le for additional information.
After running DisplayFind to determine th.e display's static IP address, reconguration of
the computer to the same IP address range and subnet may be required.
5� Follow the steps in Conguration Steps Using IP Address (p.11).

Network and Communication Installation
14
Connect A Display To A Static IP Network
Display Currently Congured for DHCP (Default)
The following steps explain how to set a static IP address on the display.
Network Requirements
• Existing Network
• Available network port, congured properly
• PC
• Internet Explorer or Firefox web browser
Conguration Steps Using IP Address
1� Connect a computer to the display.
2� Congure the computer for DHCP.
3� Turn on the display.
Note: Both the display and the computer should time out searching for a DHCP
server and fall back to auto IP addresses of 169.25x.x.x.
4� Observe boot sequence–recongure computer to same in the IP address range as
the display and same subnet.
5� Manually enter display IP address in web browser followed by :85 (for example,
http://169.254.13.87:85) to identify the correct connection port. Refer to the
Conguration Using DisplayFind To Discover The Display (p.12) section.
6� Enter User Name Dak and Password DakPassword! in the Windows Security window.
7� Click OK to connect to the display (refer to the help le for additional information
about the conguration utility).
8� Click the Network tile.
9� Click Manual under the IP Conguration heading.

Network and Communication Installation
15
10� Enter the IP address, subnet mask, default gateway, and DNS servers that you would
like set on the display.
11� Click Save.
12� Log out of the conguration utility.
13� Turn off the display.
14� Disconnect the computer from the display and connect the display to the network.
15� Ensure the display has an established link with the network.
16� Turn on the display.
Display Congured For Static IP Address
The following steps explain how to update the static IP address that is currently set on the
display.
Network Requirements
• Existing Network
• Available network port, congured properly
• PC
• Internet Explorer or Firefox web browser
Conguration Steps Using IP Address
1� Connect a computer to the display.
2� Turn on the display.
3� Observe boot sequence–recongure computer to same in the IP address range as
the display and same subnet.
4� Manually enter IP address in web browser (for example http://display IP address:85)
or refer to the Conguration Using DisplayFind To Discover The Display (p.12).

Network and Communication Installation
16
5� Enter User Name Dak and Password DakPassword! in the Windows Security window.
6� Click OK to connect to the display (refer to the help le for additional information
about the conguration utility).
7� Click the Network tile.
8� Change the IP address settings to new values.
9� Click the Save button.
10� Click Upload Conguration.
11� Turn off display.
12� Disconnect the computer from the display and connect display to the network.
13� Ensure the display has an established link with the network.
14� Turn on the display.