Universal series DALI dimmer 09.2303B.04078
Wiring diagram
Function introduction
Important: Read All Instructions Prior to Installation
• DO NOT install with power applied to device.
• DO NOT expose the device to moisture.
DC Power input
CH 1:R output
CH 2:G output
CH 3:B output
CH 4:W output
Product Data
Safety & Warnings
Manual set button
Digital display
2 groups DALI
signal input & output
• Complies to DALI standards IEC 62386-102, IEC 62386-207
• Match all DALI system in the market
• Manual /automatically DALI address setting
• DALI address digital indicate
• Four channels, can set addresses from one to four.
• To work with power repeater to expand output power unlimitedly.
• Waterproof grade:IP20
1 2
Set DALI Address Manually Via Buttons
1.1. Press and hold down any of the two buttons until numeric digital display flashes, then release the button.
1.2. Click any of the two buttons once to select a digit, click again to change the digit until the desired DALI
address appears. Click first button to set “tens” position and second button to set “units” position. The address
can be set from 00~63.
1.3. Then press and hold down any of the 2 buttons until the numeric digital display stops flashing to confirm the
setting.
Note: DALI address can be manually assigned from 00-63-FF, by factory defaults, no DALI address is
assigned for the dimmer, and the display shows . Setting DALI address as will reset the
dimmer to factory defaults.
Operation
Set DALI Address Quantity
1.1. Press and hold down both of the two buttons until numeric digital display flashes, then
release the button.
1.2. Click first button to select “1A”, “2A”, “3A” or “4A” which means 1 address, 2 addresses, 3
addresses or 4 addresses.
1.3. Then press and hold down any of the 2 buttons until the numeric digital display stops
flashing to confirm the setting.
For example, when we set address to 22:
When select 1A, all four channels will be the same address 22.
When select 2A, channel 1 & 3 will be the same address 22, channel 2 & 4 will be the same
address 23.
When select 3A, channel 1, 2, 3 will be address 22, 23, 24 respectively, and channel 4 address is
also 24.
When select 4A, channel 1, 2, 3, 4 will be address 22, 23, 24, 25 respectively.
DALI Address Assigned by DALI Masters
DALI address can also be assigned by DALI Master controller automatically, please refer to user manuals of
compatible DALI Masters for specific operations.
Note: The digital display will show When the DALI master is assigning addresses.
Input
Voltage Remarks
Output
Current
12-36VDC Constant voltage
4x(60-180)W
4x5A
Output
Power
12-36VDC Constant current
4x(4.2-12.6)W
4x350mA
12-36VDC Constant current
4x(7.8-23.4)W4x650mA
No.
1
2
3
Size(LxWxH)
178x46x22mm
178x46x22mm
178x46x22mm
2mA
DALI
Consumption
2mA
2mA
0.1%-100%
Dimming
Range
0.1%-100%
0.1%-100%
Ambient
Temperature
-20℃ ~ +50℃
-20℃ ~ +50℃
-20℃ ~ +50℃
12-36VDC Constant current
4x(8.4-25.2)W4x700mA
4178x46x22mm 2mA 0.1%-100% -20℃ ~ +50℃
• Radio Frequency Interference according to EN 55015:2013
• Immunity standard according to EN 61547:2009
• TÜV Rheinland marked, CE marked
Conformity & Standards
DALI Controller
123
4
0-6 0-9
DA
DA
DA
DA
DALI DALI
V+
V-
V+
V-
12-36VDC
INPUT
V+ V+
1- V-
2- V-
3- V-
4- V-
V+ V-
AC Power
50/60Hz
L
N
G
V+
V-
OUTPUT
INPUT
12V/24V/36V
CV PSU
DALI Master
If Single Color LED Strip
If Connect with RGBW LED Strip
V+ V+
R- R-
G- G-
B- B-
W- W-
V+ V+
WW WW
CW CW
WW WW
CW CW
If Connect with Dual Color LED Strip
DALI Contro ll er
123
4
0-6 0 -9
DA
DA
DA
DA
DAL I DALI
V+
V-
V+
V-
12- 36VD C
INP UT
DALI Contro ll er
123
4
0-6 0 -9
DA
DA
DA
DA
DAL I DALI
V+
V-
V+
V-
12- 36VD C
INP UT
DALI Contro ll er
123
4
0-6 0 -9
DA
DA
DA
DA
DAL I DALI
V+
V-
V+
V-
12- 36VD C
INP UT
