Dali DH User manual

User Manual Ver 1.0.0
Technical Parameters
Model No.: DH
Features
Page 1
Mechanical Structures and Installations
LVD
Wiring Diagram
Note:
If output connect with capacitive or inductive load, the maximum output current only up to 5A.
If output connect with resistive load, the maximum output current may up to 8A.
Setting key Digital display
DH DALI AC Switch
Output current 2CH, 5A Max
Input voltage AC100-240V
Output voltage AC100-240V
Input and Output Warranty
5 years
Warranty
Operation temperature
Case temperature (Max.)
Environment
IP20
IP rating
Ta: -30
O
C ~ +55
O
C
T c: +70
O
C
Output power 2*(500-1200)W
DALI AC Switch
● DALI control power on/off to cater for unwanted dimming lighting system, two DALI address, two channel output,
AC input and AC output.
● In accordance with DALI standard protocol IEC 62386-102, IEC 62386-208 and in compliance with DALI products
from other international incorporation.
● DALI address can be manually assigned and shown in digital display or automatically assigned by DALI master.
● The switching thresholds of the relay can be set on the DALI bus
● Zero cross switching function, 2 independently output channels AC switch.
● To switch two LED lamps, traditional incandescent and halogen lights.
2 DALI address/2 Channel AC output/Numeric display
tc: 70℃
0.5-2.0mm²
4-5mm
Wire Preparation
SIGNAL INPUT
Da2
Da1
Da2
Da1
N
N
L1
L2
DH DA LI AC Switch
Uout=100-240VAC
Iout=2*5A
Pout=2*(500-1200W)
Temp Range: -30℃~+55℃
Uin=100-240VAC
Iin=10.5A
0-6 0-9
L
N
SIGNAL INPUT
AC INPUT
AC OUTPUT 1
AC OUTPUT 2
Two groups of DALI signal input
DALI bus no need distinguish
plus-minus polarity
AC N
AC N
AC L Input
AC L Output 1
AC N
AC L Output 2
187.00 mm
46.00 mm
22.00 mm
DALI
Master
N
L
AC 100-240V tc: 70℃
0.5-2.0mm²
4-5mm
Wire Preparation
SIGNAL INPUT
Da2
Da1
Da2
Da1
N
N
L1
L2
DH DA LI AC Switch
Uout=100-240VAC
Iout=2*5A
Pout=2*(500-1200W)
Temp Range: -30℃~+55℃
Uin=100-240VAC
Iin=10.5A
0-6 0-9
L
N
SIGNAL INPUT
AC INPUT
AC OUTPUT 1
AC OUTPUT 2
tc: 70℃
0.5-2.0mm²
4-5mm
Wire Preparation
SIGNAL INPUT
Da2
Da1
Da2
Da1
N
N
L1
L2
DH DA LI AC Switch
Uout=100-240VAC
Iout=2*5A
Pout=2*(500-1200W)
Temp Range: -30℃~+55℃
Uin=100-240VAC
Iin=10.5A
0-6 0-9
L
N
SIGNAL INPUT
AC INPUT
AC OUTPUT 1
AC OUTPUT 2
N
L
AC 100-240V
Please carefully ensure all wire connections and polarities are correct and secure before applying power,
otherwise this controller will be damaged.
Caution:
LED light
Weight
123g
Gross weight
weight
140g
LED light

User Manual Ver 1.0.0 Page 2
DALI address can also be assigned by DALI Master controller automatically.
Please refer to user manuals of compatible DALI Masters for specic operations.
The digital display will show “AU” When the DALI master is assigning address.
After address is assigned, the digital display will show the start DALI address”xx”, xx is from 00 to 63.
DALI address assigned by DALI masters
● Long press any of the two buttons for 2s, prepare for set the start DALI address, digital display start ashes.
● Short press rst button to set “tens” position and second button to set “units” position.
● The address can be set from 00~62-FF. no DALI address is assigned for the dimmer, digital display shows “FF”.
● Address assignments are sequential. If the set address value is 01, the CH1 address value is 01, and the CH2 address value is 02,
The display shows the CH1 address value.
● Long press any of the two buttons for 2s or timeout 10s, quit start DALI address setting, digital display stop ashes.
Set DALI Address via buttons
● Long press two buttons at the same time for 2s, Toggle Relay Switch: On(”On”) and Off(”OF”).
● Enter the default setting to on(”On”), then short press the setting 1 key to turn on(”On”), short press the setting 2 key to turn off(”OF”).
● Long press any of the two buttons for 2s or timeout 10s, quit Relay switch setting.
Operation
Relay switch setting
DH DALI AC Switch