danalock Danabridge V3 User manual

Danabridge V3
www.danalock.com EN

2

3
A

4

5
B

6

7
guide.danalock.com
The following instructions are in english. Localized versions can be
found with the QR-code below.

8
Add the Danabridge V3 in the Danalock App
Open the Danalock App and add the Danabridge by selecting ”Add
device” in the menu tab. When the Danabridge has been enrolled
you can pair it with your Danalock V3.
Go to:
Menu > My Accessory Devices > [Danabridge name] > Pairing
Select the lock you want to control with the Danabridge V3.
Connect the Danabridge V3 to wi
Go to:
Menu > My Accessory Devices > [Danabridge name] > Wi
Select your access point and enter the credentials. The Danabidge
V3 is ready for use when it has connected successfully.

9
LED-Signals
The Danabridge V3 indicates the status of several operations with
dierent colors:
LED signal LED color Status indication
Long white blink Power on
Constant green light Device is online
Constant red light Device cannot access Wi-Fi
Yellow blinking Device has not been congured
Red blinking Device has no connection to server
Green blinking Device communicating with server
Constant purple light Device is ready to update
Blue while performing action Device is updating

10
Conguring the Danabridge V3 with click-commands
You can congure the Danabridge via the button found in the small
hole on the side.
When you get to the setting you want to change, wait for 5 seconds
and the Danabridge will react to your command. If you make a
wrong number of clicks, just stop at a number of clicks where the
LED doesn’t light up and wait for 5 seconds. The LED will ash red to
indicate that it has timed out.
Clicks Color Activity
10 Red Reset user settings
This action deletes all user settings on the Danabridge.

Firmware upgrade
Go to:
Menu > My Accessory Devices > [Danabridge name] > Firmware
and press ”Upgrade rmware”. Make sure to keep your phone near
the Danabridge V3 during the entire rmware upgrade process.

Simple Guidelines
Please follow these guidelines when conguring, using,
or recycling the DBV3. Violating these guidelines may be
dangerous, illegal, or otherwise detrimental. Further detailed
information is provided in this manual.
Terms of use
This equipment design is primarily for indoor use mounted
in a standard electrical outlet. Use only Danalock approved
accessories for the DBV3. Do not connect incompatible
products, and do not operate the DBV3 where wireless radio
communication is prohibited. Like hospitals, buildings near
blasting sites etc.
Do Not Operate Where Prohibited
Do not allow the DBV3 unit to operate wherever wireless
radio communication use is prohibited or when doing so may
cause interference or danger as the DBV3 cannot be turned
o after installation.
Device Operation and human exposure to electromagnetic
elds
The DBV3 unit is a low power radio transmitter and receiver.
Periodically the DBV3 wakes up either due to activity or
by a timer. When it is ON, it receives and sends out radio
frequency (RF) signals for a short period of time.
Specic Human Absorption Ratio (SAR)
The DBV3 unit is not intended for handheld use or to be
worn on the body. A minimum separation of eight (8”) inches
(20 cm) is to be maintained between the DBV3 and any
persons’ body.
Pacemakers and other Medical Devices
If any other personal medical devices are used in the vicinity
of a DBV3 unit, consult the manufacturers of the medical
devices to determine if they are adequately shielded from
external RF energy. Physicians may be able to assist in
obtaining this information.
Interference
Like all wireless devices, the DBV3 may encounter electrical
interference that may aect its performance. The DBV3 is
tested and certied according to international and European
standards. The performance hereof ensures correct
operation in the presence of electromagnetic interference
and/or electrostatic discharge.
Category of use
The DBV3 WiFi interface is an accessory to other Danalock
products and will only work together with these to access
the internet.
Security for electrical functions
The DBV3 has no indications, sound alarms in case of a
connected lock malfunction.
Security for electrical manipulation
The DBV3 is tested compliance to the EMC requirement laid
out in the 2014/53/EU directive. The performance hereof
ensures correct operation in the presence of electromagnetic
interference and/or electrostatic discharge.
Children
The DBV3 series and its accessories are not used to solicit
data from or market to children
CE mark
The DBV3 complies with the essential requirements of
the RED directive 2014/53/EU directive with respect to
the radio spectrum, EMC, Health and safety. EU Certicate
and Declaration of conformity (DOC) statements can be
downloaded from the homepage:
https://danalock.com/legal/certicates/
Product specications
Supply Voltage Via USB 5V DC, 1A
Temperature
range
Active operating mode 0ºC to +40ºC
Storage 5ºC to +40ºC
Mechanical
specications
Dimensions (D x H) 53 mm x 32 mm
Weight 36 g
Material Plastic White ABS
Radio
interfaces
WiFi Max 12 dBm
Bluetooth LE Max 4 dBm

Warranty
Danalock ApS products are covered by a limited
manufacturer warranty. The Danalock ApS warranty is limited
to the warranty rules and legislation present in each country.
The warranty only covers manufacturing faults. The warranty
does not cover misuse, wrong installation or damage due to
a faulty installation or wrong maintenance.
The invoice act as the proof of warranty, so please keep it as
reference for any warranty complaints.
Qualied Service
The Danabridge V3 contains no user serviceable or
replaceable parts. Non-functioning units must be returned to
an authorized service center for repair or replacement.
Technical Assistance
If you have a problem and cannot nd the information you
need in the product
documentation, please contact Danalock ApS at support@
danalock.com. Please have the following information ready:
1. Serial number (preferred), MAC address or alias of the lock
2. Username used when registering / installing the lock
3. Username used when getting the error (if dierent
username)
4. Time of incident
US and Canada certication marks
This device contains radio transmitters that comply with CFR
47 part 2.1091, part 15.207, Part 15.247 of the FCC rules
and with RSS-GEN, RSS-102 and RSS-247 of Industry Canada
requirements
Notice statements according to CFR 47 Part 15.19 / RSS-GEN:
The device complies with Part 15 of the FCC rules and with
Industry Canada license
exempt standard(s). Operation is subject to the following
two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received,
including interference
that may cause undesired operation.
Déclarations selon le CFR 47 section 15.19 / RSS-GEN:
Le présent appareil est conforme aux CNR d’Industrie
Canada applicables aux appareils
radio exempts de licence. L’exploitation est autorisée aux
deux conditions suivantes:
(1) l’appareil ne doit pas produire de brouillage, et
(2) l’utilisateur de l’appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible
d’en compromettre le fonctionnement.
NOTICE statements according to CFR 47 Part 15.21:
Changes or modications made to this equipment not
expressly approved by Danalock Aps may void the FCC
authorization to operate this equipment.
Statements according to CFR 47 Part 2.1091 and RSS-102:
With respect to radiofrequency radiation exposure
Information it is declared that this equipment complies with
FCC radiation exposure limits set forth for an uncontrolled
environment.
This equipment should be installed and operated with
minimum distance of 20 cm between the radiator and
your body.
This transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter.
Déclarations selon le CFR 47 Sections 2.1091 et RSS-102:
Respectant les informations relatives à l’exposition aux
radiations de fréquences radio, on déclare que cet
équipement respecte les limites d’exposition aux radiations
de la FCC aux conditions prévues pour un environnement
non contrôlé.
Cet équipement doit être installé et fonctionner à une
distance minimale de 20 cm entre l’appareil irradiant et
votre corps.
Cet émetteur ne doit pas être installé ou utilisé en
conjonction avec d’autres antennes ou d’autres émetteurs.
FCC part 15B note
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses

and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause
harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment o and on, the user is
encouraged to try to correct the interference by one or more
of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and
receiver.
— Connect the equipment into an outlet on a circuit dierent
from that to which the receiver is connected.
Australia and New Zealand
This product complies with the AS/NZS 4268 requirements
for Bluetooth LE transceiver (2402 MHz ~ 2480 MHz ) and
WiFi transceivers (IEEE 802.11b/g/n-HT20): 2412MHz ~
2472MHz.
The product complies with the requirements of the relevant
ACMA Standards made under the Radiocommunications
Act 1992 and the Telecommunications Act 1997, by
the Supplier’s Declaration of Conformity (SDOC). These
Standards are referenced in notices made under section
182 of the Radiocommunications Act and 407 of the
Telecommunications Act.
The product complies with the requirements of the relevant
standards under Section 134 (1) (g) of the New Zealand
Radiocommunications Act 1989, by the Supplier’s Declaration
of Conformity (SDOC)
Japan
The product is approved in Japan with the certicate ID n°:
[R] 204-820373
This device is granted pursuant to the Japanese Radio
Law (電波法)
=当該機器には電波法に基づく、技術基準適合証明等を受けた
特定無線設備を装着
している
This device should not be modied (otherwise the granted
designation number will become invalid)
本製品の改造は禁止されています。（適合証明番号などが無
効 と なりま す 。)
Regulatory labeling:
The Danabridge V3 product are regulatory compliant
to the following regulation (Europe, USA/Canada, Japan,
Australia/NZ):
204-820373
REACH
COMPLIANT
RoHS
2011/65/EU
Amendment
2015/863/EU

BRIDGEV3-EN-2020/10/22
Danalock ApS
Gammel Stillingvej 427C
8462 Harlev, DK
[phone]
[email protected]
www.danalock.com