Danatronics DJ Series User manual

DANATRONICS DJ Series
Videoscope
Product Manual

Inspection technology for better future.
Please read the manual before using the equipment.

Declaration
The manual is only intended to be used for the DJ Series
As this manual is used a product series manual, the configuration and function of
different products may slightly differ depending on your exact configuration. The
technical specifications are only for reference.

MENU
Instruction Before Use........................................................................... 1
Main Configuration............................................................................. 1
Button and Port................................................................................... 3
Application........................................................................................... 5
After-service........................................................................................ 5
Warning ............................................................................................... 5
1 Brief Introduction................................................................................. 6
1.1 Parameters ................................................................................... 6
2 Operation Steps .................................................................................. 9
2.1 Take out the instrument............................................................. 9
2.2 Boot preparation ......................................................................... 9
2.3 Operation .................................................................................... 10
2.4 Probe articulation control ......................................................... 11
2.5 After use...................................................................................... 11
3 Image Capture and Operation ........................................................ 13
3.1 Photo/Video................................................................................ 13
3.2 Temperature indication & alarm (optional, not standard
configuration) .................................................................................... 13
3.3 Image special effects ................................................................ 14
3.4 Exposure control........................................................................ 14

3.5 Playback ..................................................................................... 14
3.6 Measuring function(optional, not standard configuration)... 15
3.7 Zoom in/out................................................................................. 15
3.8 Language setting ....................................................................... 15
3.9 Date&Time setting..................................................................... 15
3.10 Auto shut off............................................................................. 16
3.11 Date Stamp .............................................................................. 16
3.12 Formatting ................................................................................ 16
3.13 Factory reset ............................................................................ 16
3.14 Firmware update ..................................................................... 16
4 Solution to Common Problems .................................................. 15

1
Micro USB/ charger
Videoscope
TF card reader
Base(optional)
Instrument Case
Instruction Before Use
Main Configuration

2
For the specific configuration, please refers to the packing list.
Name Specs Qty Note
Case 432*386*163 mm3 1
Videoscope 324.3*161.3*91.2mm3 1
Base 215*84*36mm31 Optional
TF card reader 1
Rechargeable Battery φ18mm×65mm 1 Optional for 2pcs
Micro USB Line 1m 1
Charger 1

3
Button and Port
working indicator
⑵ok/function switch
⑸playback
⑽resetting
⒀Micro USB
⑾HDMI
⑿
TF card
⑼photo/video
⑻front view/side view switch
⒂on/off
power indicator
⒁charging port
⑷return
⑴menu
⑹up
⑶brightness control
⑺down

4
（1）Menu: function setting including language setting/ time setting
/firmware update.
（2）Ok: in menu setting mode, it serves as a validation button; in preview
mode, press ok button, it serves as function switch button.
（3）Brightness control: control the light from 0-9 levels.
（4）Return: return to previous menu.
（5）Playback: in preview mode, press this button, it will go to
image/video playback page.
（6）Up: in menu setting mode, press this button to upward navigation;
in preview mode, after pressing OK button, it can adjust the relative
function variable.
（7）Down: in menu setting mode, press this button to downward
navigation; in preview mode, after pressing OK button, it can adjust
the relative function variable.
（8）Front view/side view switch: In preview mode, press this button to
switch between front view and side view lens. (only available for dual
lens model)
（9）Photo/video: short press for taking photo, long press for taking video.
In video mode, short press for snapping a picture.
（10）Resetting: when the monitor does not work for abnormal reason,
press this hole by needle, it will restart.
（11）HDMI: connect the monitor with display by HDMI cable, the image on
the monitor will be displayed synchronously on the display.

5
（12）TF card: please use Class 10 or above TF card. Maximum: 32G.
（13）Micro USB: When the monitor works independently, it serves as
power input port. When it connects with power bank or mobile phone
charging adapter, the monitor will turn on automatically.
（14）Micro USB charging port: power charging: DC5V, maximum
current:1A.
(15) On/off: Long press this button for 3 seconds to boot; long press it for
3 seconds to shut down. On the status of shut off, short press it, the
power indicator will show the current power of the batteries. The
current power of the two batteries will be indicated separately, orange light
shows the power of inner battery, white light shows the current power of outer
battery. When the product is charging, the indicator will flash. When the
product is turned on, the indicator will show the current power all the time.
Application
This product is only applied in the real-time detection and analysis for industrial
equipment and automobile production and maintenance.
After-service
This product has not any spare parts which can be repair by users. Any
disassemble, refit or maintenance is not allowed. If damage and losses
caused by this, we do not assume any responsibility. The product
maintenance is only afforded by the authorized dealers and distributors.
Warning
warning

6
·Prohibit the use of this instrument to observe the body or the animal's body;
·Do not use the product to inspect equipment in action;
·Do not use or store the product on explosive, strong electromagnetic field or
with combustible gas, otherwise it may cause fire or explosion;
·Do not use the product to check objects with current carrying, so as to avoid
the occurrence of electric shock;
·Do not watch the LED light source at the end of the lens straightly, avoiding
the effect of strong light on the visual acuity;
·Never excessive bending, stretching, twisting, rolling cable, otherwise it may
cause cable disconnect, a fire or electric shock accident;
·If there is abnormal in the angle adjustment operation, stop the current
operation, and turn off. Then contact the supplier;
·Keep the insert tube away from any liquid, except water, salty water or oil;
·When finish using, please clean the front section of the instrument in time, to
prevent corrosion.
1 Brief Introduction
1.1 Parameters
Probe Diameter(mm) Φ6/Φ3.9/Φ2.8
Camera Pixels 1000,000
DOF 5mm-100mm (optional:10~150mm)
FOV 120° (optional: 80°)
Viewing Direction 0° front view (optional: 90°sideview)

7
Illuminance Maximum:100000lx
Tube Material Tungsten braided
Tube Length 1.5m (customized for other length)
Protecting Device of
Durability
buffer protection device between the host and
wear-resistant tube
Articulation 360° all way
Bending Angle ≥160°
Probe Positioning damping positioning (optional: articulation
locking device)
Display 5.1 inches color IPS display, all sight viewing
angle
Display Resolution 1280*960
Language Chinese/English/Russian…8 languages
Image/Video Format JPEG/MOV
Image Format 1280*720
Video Format 1280*720
IR Function IR night vision/ IR thermal imaging (optional)
Outer Case Material anti-fall engineering alloy material
Water/Dust Proof probe/tube: IP67
Monitor Structure one hand-held monitor
Memory standard TF card 16G, maximum: 32G
Data Port HDMI port/Micro USB port
Working Time ≥4H, built-in batteries:8H
Batteries detachable lithium batteries (optional: built-in
lithium batteries)
Battery Capacity 3.7V，3200mAh*2pcs

8
Power Consumption 2W
Power Charge DC5V, maximum current:1A
Weight 0.55~0.8kg (including 2 batteries)
Compatibility
replaceable monitor and tube with different
diameter
Store Temperature -23℃~63℃
Relative Humidity maximum: 92%, non-condensing
Monitor Working
Temperature
-30℃~60℃, when 0°C below, the display needs
preheating.
Camera Working
Temperature
-25 ℃~80 ℃, when 0°C below, please reduce
probe articulation.

9
2 Operation Steps
2.1 Take out the instrument
When removing the instrument from the case, be careful to not kink the cable or
scratch the camera lens
2.2 Boot preparation
Check to be sure the insertion tube is connected to the monitor, the SD card and
batteries are installed (one battery also works normally). Straighten the insertion
tube.
③
monitor
①
②
⑥
④
tube system
⑤

10
* Connect the monitor to the insertion tube system; (1-5)
* Make sure the monitor us making contact with the upper portion of the handle
(1-5)
* Lock the button on the back of the monitor; (4)
* Install the SD card.
2.3 Operation
The DJ Series has10 levels of brightness adjustment. Press the light control
button to change the level. Slowly insert the tube to the inspected object. The
operation interface is as follows:
image rotation
full screen/zoom
measurement
exposure
special effect
TF card
white balance
preview mode
battery power
brightness
temperature
image freezing

11
2.4 Probe articulation control
According to the testing need, operate the joystick to control probe articulation.
The bending motion of the front probe is controlled by rotating the joystick.
During operation, if the joystick suddenly meets resistance, or there is any
abnormity, please immediately stop using. Adjust the joystick to the middle
position and carefully remove the insert tube from the tested equipment.
The articulation lock device is optional. When the probe is articulated to the
suitable position, if screw down this device, the articulation will be locked.
2.5 After use
Before you remove the insertion tube from the inspected object, please make
sure the probe is reset to straight. If the product is damaged due to improper
articulation lock device
front view / side view switch
(available for dual lens model)

12
operation, the user is responsible for the damage. Turn off the power switch, put
the instrument into the portable case carefully, and put the tube into the case.

13
3 Image Capture and Operation
3.1 Photo/Video
①Short press “(9) photo/video button”;
②The image will freeze a frame, indicating a photo has been captured and
saved automatically. The saved file is named in the form of Date+No.
Such as:
③Long press “(9) photo/video button” for 2 seconds, it will start to record
video and the upper right corner of the screen will show the record time.
When finished, press “(9) photo/video button” for 2 seconds again to stop
the video. The file will be saved automatically.
3.2 Temperature indication & alarm (optional, not standard configuration)
No.
YTD
20170725 001.JPEG

14
Temperature indicator is on the upper left of the screen. When the testing
temperature is 20℃~64℃,it indicates in green color. Orange alarm when the
probe temperature is 65℃~79℃; red alarm when above 80℃. For the protection
of the probe and camera, the monitor will shut off automatically.
3.3 Image special effects
In preview mode, press “(2) OK” button, select , which stands for standard
color mode. Press “(6) up” button or “(7) down” button, it changes to
negative film mode or black&white mode, in cyclic switch.
3.4 Exposure control
Press “(2) OK” button, select , which stands for exposure control mode.
Press “(6)up” button or “(7) down” button, it can switch the exposure level,
including 5 levels: -2/-1/0/+1/+2, in cyclic switch. According to the inspection
environment, users can adjust different exposure level, in order to get clearest
image.
3.5 Playback
In preview mode, press “(5) playback” button, it will change to image playback
mode. Press “(6) up” button or “(7) down” button to playbacks different images.
Press “(1) menu” button to pop up image delete menu, deleting images. Press
“(5)” button again, it will switch to video playback mode. Press “(2)” button to
playback video. Press “(2)” again to pause.