Ryobi RLL25GN User manual

RLL25GN

2
Original Instructions
IMPORTANT!
It is essential that you read
the instructions in this
manual before assembling,
operating, and maintaining
the product.
Subject to technical
modifications.
Safety, performance, and
dependability have been given
top priority in the design of your
360° line laser.
INTENDED USE
The 360° line laser is intended
to be used only by adults who
have read and understood
the instructions and warnings
in this manual, and can be
considered responsible for
their actions.
The product is intended for
determining and verifying
horizontal and vertical lines.
The product is intended for
indoor use only.
Do not use the product for
any other purpose. Use of the
product for operations different
from intended could result in a
hazardous situation.
CROSS LINE LASER
SAFETY WARNINGS
■Laser radiation. Do not stare
into beam. Class 2 laser
product.
■Risk of severe eye injury if
the laser beam is directed
at persons or animals. Avoid
direct eye exposure.
■Do not direct the laser beam
towards other people.
■Do not operate the product
around children or allow
children to operate the laser.
■Avoid using the product on
reflective surfaces. The laser
beam may be reflected at the
operator or other persons.
■When the product is brought
into a warm environment
from a cold one, or vice
versa, allow it to come to
the surrounding temperature
before use.
■Store the product indoors
and avoid substantial
knocks, continuous vibration
or extreme temperatures.
■Always keep the product
away from dust, liquids and
high humidity. They may
damage internal components
or affect accuracy.
■If laser beam hits your eye,

3
Original Instructions
you must close your eyes
and immediately turn your
head away from the beam.
■Do not position the
laser beam so that it
unintentionally blinds you or
others.
■Do not look into a laser beam
using magnifying optical
devices such as binoculars
or a telescope. This will
increase the level of eye
injury.
■If you use laser goggles to
enhance the visibility of the
laser beam, note that they
will not protect your eyes
against laser radiation.
■Do not remove or deface
warning labels on the
product.
■Do not disassemble the
product.
■Avoid heavy impact to
or dropping of the laser.
The accuracy of the laser
should be checked before
use if it has been dropped
or subjected to other
mechanical stresses.
■Do not operate the product
in explosive areas or in
extreme environments.
■When not in use, make sure
to turn off the power, and
place the laser in its carrying
pouch. Make sure the on/off
switch is in the off position
before transporting the laser.
NOTE: If the on/off switch is
not in the off position before
transportation, internal
mechanical damage may
occur.
■If the product is not in use
for a long period of time,
remove the batteries from
the battery compartment.
This will prevent batteries
from leaking and corrosion.
SELF-LEVELLING LED
INDICATOR
LED
indicator
Explanation
Green Self-leveling is
complete.
Red Self-leveling is
not successful;
laser line
blinks. Place
the product in
a horizontal
position of
+/-4°.
MAINTENANCE
■Avoid using solvents when
cleaning plastic parts. Most
plastics are susceptible to
various types of commercial

4
Original Instructions
solvents and may be
damaged by their use. Use
clean cloths to remove dirt,
carbon dust, etc.
■For greater safety and
reliability, all repairs
should be performed by an
authorised service centre.
SYMBOLS ON THE
PRODUCT
V Volts
Direct current
Regulatory Compliance
Mark (RCM). Product
meets applicable
regulatory requirements.
Read the instructions
carefully before using
the product.
Class 2 laser beam. Do not
stare into the laser beam.
Do not dispose of
waste batteries, waste
electrical and electronic
equipment as unsorted
municipal waste. Waste
batteries and waste
electrical and electronic
equipment must be
coll ected separately.
Waste batteries, waste
accumulators, and
light sources have to
be removed from the
equipment. Check with
your local authority or
retailer for recycling
advice and collection
point. According to
local regulations,
retailers may have an
obligation to take back
waste batteries and
waste electrical and
electronic equipment
free of charge. Your
contribution to the reuse
and recycling of waste
batteries and waste
electrical and electronic
equipment helps to
reduce the demand of
raw materials. Waste
batteries, in particular
containing lithium, and
waste electrical and
electronic equipment
contain valuable and
recyclable materials,
which can adversely
impact the environment
and the human health
if not disposed of in
an environmentally
compatible manner.
Delete personal data
from waste equipment,
if any.

5
Original Instructions
SYMBOLS IN THIS
MANUAL
Note
Do not stare into the
laser beam.

6
Know your product
Vertical laser beam window
Operator’s manual
Battery
Battery door
Self-levelling LED indicator
Mode selector
Mounting screw hole(1/4”)
ON/OFF switch
Storage pouch
360° horizontal laser
beam window
x 4

7
Getting started
1
2
1
2
2

8
Getting started

PRODUCT SPECIFICATIONS
25M 360 Green Line Laser
Model RLL25GN
Accuracy ±0.5 mm/m
Laser wavelength 520nm ± 10nm
Colour Green
Working range 25 m
Laser class 2, <1mW
Beam divergence 1.5 mrad
Projection Plane and vertical line
Self-leveling time 2s ~ 4s
Self-leveling angle ± 4°
Operating time 5 h
Battery technology 4 x AA LR6 Alkaline
Supply voltage 4 x 1.5V
Operating temperature range 0°C ~ 40°C
Storage temperature range -20°C ~ 70°C
Dimensions L86 x W70 x H110 mm

RYOBI is a trade mark of Ryobi Limited, and is used under
license.

Imported by:
Techtronic Industries Australia Pty Ltd
31 Gilby Road, Mount Waverley, VIC 3149
Melbourne, Australia
Techtronic Industries N.Z. Limited
Unit C, 70 Business Parade South,
Highbrook, Auckland 2013, New Zealand
RYOBI is a trade mark of Ryobi Limited, and is used under license.
20230303v1