Dancover Storage Tent PRO User manual

6m PVC Series
Storage tent PRO
Manual
07-08-2013

Safety Advice
Attention
In some countries approval is needed to set up a marquee/tent larger than 75 m2. It
is your responsibility to comply with local rules and regulations and to ensure that
the marquee/tent is assembled correctly.
In case of bad weather conditions, it is your responsibility to ensure the
marquee/tent is safely secured and that the marquee/tent does not cause damage
to others.
close to the tent.
The marquee/tent must be safely secured. We recommend you secure your
marquee/tent with straps and pegs as soon as it is assembled.
Make sure to check if the marquee/tent is covered by your home contents insurance.
Marquees/tents must be evacuated under extreme weather conditions.
In the event of snow always remove snow from the roof of the marquee/tent
regularly to prevent snow from building on the roof as heavy snow can cause the
marquee/tent to collapse.
In the event of rain there is a risk of rain puddles building up on top of the roof of the
marquee/tent. Heavy rain puddles can cause the roof to collapse. It is your responsi-
bility to ensure rain puddles do not build up. As a precaution, make sure theroof of
the marquee/tent is stretched out properly and adequately over the side frames of
the marquee/tent and remove rain water regularly.
Please always check our website for the latest safety advice and manuall.

1
Part list
6x6
6x12
6x18
1 Back leg 4 6 8
2 Back leg 8 16 24
3 Crossbar 8 16 24
4 Ceiling rail 6 11 16
5 Ceiling rail 6 11 16
6 Extension pipe 4 4 4
7 Corner arch 12 22 32
8 Center arch 6 11 16
9 Connecting
pipe 44 99 154
10 Connecting
pipe 11 11 11
11 Extension pipe 8 18 28
12 Door Pillar 4 4 4
13 Door pillar 4 4 4
14 Cross bar 8 8 8
15 Fastening bar 10 20 30
16 Foot base
16 26 36
17 Connecting
component
4 4 4
18 Peg
10x305mm
8 16 24
07-08-2013

2
19 6x1
Peg
Peg
Spiral peg
80mm
34 60 78
20 8x300mm
24 44 64
21 10x400mm 4 4 4
22 1.75"Screw
6 11 16
23 2.5" Screw
12 22 32
24 4" Screw
70 124 180
25 Wingnut 88 157 228
26 Floor Bracket
(set of 2 pcs)
4 8 12
27 Bungee ball 96 96 96
28 Spanner 2 2 2
29 Bolt with nut
16 26 36
30 Tie-down kit 4 4 4
31 Steel clip 20 40 60
32 Rope
4 4 4
33 Rope
2 2 2
Attention
Please use gloves when assembling the metal frame portion of this unit. The metal components of
this products have been treated,with a rust preventive coating that may feel oily to the touch. This
coating is not dangerous, but may dirty your hands during assembly. We recommend that you wipe
the metal parts clean with a mixture of warm water and dish detergent prior to assembly. Should
your hands become dirty, simply wash with soap and water.
07-08-2013

3
After the whole frames are set up, they should be the same as the picturesbelow.

4
Please assemble the frame as below steps. They have similar assemble steps. Here we take 6x6 for example .
Step 1
When assembling the tent, make sure that all the wingnuts
are attached to the inside.
Connect one center arch pipe(8) with the extension pipe
Attached the corner arch(7) to the ends of the extension
pipe(6). Now connect the ceiling rail(4 and 5) with each other
using the 1.75”(22) screw and the wingnuts(25). Connect the
ceiling rail with respective extension pipe(6) using the
2.5”(23) screws and wingnuts(25).
Step 2
Repeat step 1 for the next 5/10/15 elements to place them
on the ground one after another, as illustrated.
Attention: all elements with extension pipe no.6 need to be
placed at the ends. Extension pipe no.6 has holes for door
pillar.
Step 3
Now connect the 6 arch elements with each other using the
connecting pipes (9 and 10). Not that only corner arch 10 are
used for the front segments. Use the 4”(24) screw and
wingnut(25)to tighten them.

5
Step 5
Unfold the tent cover and put it over the frame.
Insert the fastening bar into the loop at the lower
end of the rood and fasten it with steel clips(31).
Attach the endwall to the fram using the bungees.
Tension the roof cover to the tent frame to the
ground using pegs 8x300mm(20)
Step 4
Start setting up one side rst. Connect the corner
arches(7) to the legs (1 and 2). Secure the frame
using the connecting pipes(9 and 10). Attach the
diagonal pipes(3) to the back legs(1). Please refer
to the complete frame pictures to attach the
diagonal pipes.
Tighten the tent at the feet using the
4’’screws(24) and the wingnuts(25).
Use the oor bracket(26) and the pegs
10x305mm(18) to fasten the frame to the ground.

6
Step 6
Assemble the pillar set like below picture .
Step 7
Use ropes to attach the door and cover the the frame. To nd a proper way and strength to attach the cover to frame
carefully. Please do not use too much strength to tear the eyelet out of frabric

Contact information
Head office:
Dancover A/S
Nordre Strandvej 119 G
3150 Hellebæk
Denmark
For more information
please visit:
www.dancovershop.com
National contact
Denmark:
[e-mail]
UK:
[e-mail]
Spain:
[e-mail]
Italy:
[e-mail]
Germany:
[e-mail]
Switzerland:
[e-mail]
France:
[e-mail]
Austria:
[e-mail]
Sweden:
[e-mail]
Finland:
[e-mail]
Nederland:
[e-mail]
Poland:
[e-mail]
Ireland:
[e-mail]
Luxembourg:
[e-mail]
Belgium:
[e-mail]
Norway:
[e-mail]