Dane Industries QuicKart 2000 User manual

Pa
g
e i
Gatekeeper Ex. 1031
Petition for Inter Partes Review

Page ii
Page ii

ToPIC
QUICKART 2000
OWNER'S MANuAL
OPERATING INSTRUCTIONS
TRAINING
GUIDE
TABLE OF CONTENTS
SECTION
Owner's Manual and Operating Instructions...................................l
Troubleshooting Flowchart .............................................................2
Training Manual ..............................................................................3
Certified Operator's Test ................................................................
.4
Nate on radio equipment used:
This device complies
with part 15 ofthe FCC Rules. Operationis subject to thefollowing two conditions: (1)
This device
may not cause harmful interference, and (2) This device must accept any interference received,
including intelference
that may cause lmdesired operation.
Note:
This equipment has been tested and found to complywith the limits for a Class B digital device,
pmsuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference
in a residential installation. This equipmentgenerates, uses, and canradiate radio
frequency energy and,
if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there
is no guarantee that intetference will" not occur in a
pmticular installation.
If this equipment does Cause harmful interference to radio or television reception, which
canbe'detel1nined by turning the equipment
off and on, the user is encomaged to try to conect the interference
by one or mOre ofthe following measures:
Reorient orrelocate
the receiving antenna.
Increase the separationbetween the equipment
and receiver.
Connect the equipment into
an outlet on a circuit different from that which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
The abbreviation IC, before the CanadianRegistration Number signifies that registration was pe1fol1'lled based
on a Declaration of Conformityindicating that Indushy Canada technical specifications weremet. It does not
imply that Industry Canada approvedthe equipment.
The
CE mark, if present, declm"es that this equipment meets relevant ED Directives and Standards.
DANE INDUSTRIES, INC. QmcKART 2000 OWNER'S MANUAL
5400 Nathan Lane N. , Suite 150, Plymouth, MN 55442 I 888-544-7779 I 763-544-7779 I Fax [phone]
WWW.DANEllIDUSTRIES.COM
Page iii

·<'.i
:;.'
i ~ •
Page iv
; ,
I x .
F ‘ ‘ :-
3 )
.1 J.
a a
u x
s
Page iV

QmcKART2000
OWNER'S MANUAL
OPERATING INSTRUCTIONS
TABLE OF CONTENTS
Warning and Safety Notes ...........................................................1 +2
QuicKart 2000Labels .................................................................. 3
QuicKali 2000 Locations .............................................................. .4
QuicKali 2000 Cart Strap Accessories ................................................ 5
. Cart Restraint Assembly ............................................................ 6+7
Unpacking the QuicKart ........................................................ 8
ImportantMaintenance Notes
................................................. 9
Overview
of Operation.......................................................................... 10
QuicKart Top ViewDiagram ................................................................ 11
System Wiring Diagram ........................................................................ 12
System Junction BoxDiagram ............................................................ 13
System Junction BoxDiagnostic Lights.......................:........................ 14
QuicKali Side View Diagram.....,..................:....................................... 15
QuicKali Rear ViewDiagram ............................................................... 16
.
Cart Coupler and Roller Guide Assembly Diagram ........................ 17
Attaclnng the Collection Cali Diagram........................................... 18+19
Orientation
to the QuicKart ...............................,.............................20+21
Remote Control and Control Panel Diagrams ....................................... 22
Operation of QuicKart.....................................................................23+24
QuicKart Battery Charging....................................................................
25
Remote Control: Battery Changing ....................................................... 26
Remote Control: Battery Changing Diagram ........................................ 27
Programming the Remote
ControL ...................................................... 28
Maintenance........................................................................................... 29
Changing Tires................................................................................. 30+31
Technical Specifications.................................................................. 32+33
Warranty ................................................................................................ 34
DANE INDuSTRIES, INc. QUICKART 2000 OWNER'SMANDAL 5
5400 Nathan LaneN. , Suite 150, Plymouth, MN 55442 / 888-544-7779 / 763-544-7779 / Fax [phone]
WWW.DANElNDUSTRffiS.COM
Page v

Page vi
Page Vi

1L- __ Q_U_I_C_K_AR_T_,_20_0_0_W_'ARNI __ N_G_' ,_&_S_A_F_' E_' T_Y_N_O_T_E_S_--II
,Please read all the infOlmation included in this manual and the service instructions prior to
operating or servicing the QuicKart. In addition, malce certain all operators have been
given and passed the
certifi~d operators course before using the QuicKart.
IMPORTANT SAFETY NOTE:
THE RED BATTERY PLUG MUST BE DISCONNEcTED FROM THE
JUNCTION
BOX ANY TIME MAINTENANCE IS BEING PERFORMED
UNDERT.H.E COvER! (See diagram on page12.) , ,
'.
j) , • ']'Ile blli9Kart'is)e;;igned to push shopping c;rts.', Any other us~ of thy,QnicKart is
,.'prohibitydUules~, specifically endorsed by themanufactu,rer. Improper JlSilge and
ope~·atiqn.ofth,eQuicIZ~rtmay voidthe wananty. ' "',:"
, You must be at least 16 years old witll a.valid dr~ver:s license Or visioll test to
operate the QuicKart. In certain states, regulationsmay reqJlire operators to be
older. Please check your state's regulations regarding operation of motorized
•equipment before usingthe QuicKart.
J') '.".Neverc~rry,p~~sel{gers onthe QuicI~51rt 2000! "
4) The QuicKart is equipped with a brake which automatically engages when the
. machirle is turned off 01' not in motion. .To avoid an accident, ~.o nt,lt leflve the
machine parked or unattended on slopes. When the ,QJlicKati,is to be left
unattended or in storage, tum it "OFF" and remove the key.
5)" Do not leave the QuicKatiUllattended while it is tumed "ON". ,
~) ,"Operate the QuicJS:artat a safe speeq;go only as fast as saJetyconsideratiolls allow.
."Take into consideration the location of store entrances, sidewalks,'pedestrian and
vehicle traffic, driveways, and parking lot layout.
1)
8)
"Always operate ,in ,~low speed when near st~re guests. Operating conditions, such as
" \yet or,~lippe!y pavement or slopes can affect the st~ppingdistaqce ofthe Ql1icKati.
Do, not push more,carts tllan the ind~vidual operator can safely confro,! wh,yn those
conditions are present. Do
not exceed 20 carts at a time under any circumstance.
VerifY all waming and emergency Labels are legible and mounted in conect area's
shown on drawings shown onpages 3 and
4.
DANE INDUSTRIES, INc.
QUICKART 2000
OWNER'S MANuAL 1
5400NathanLane N. ,Suite 150, Plymonih,MN 55442 / 888-544-7779 / 763-544-7779 / Fax[phone]
WWW.DANEINDUSTRIES.COM

9)
10)
11)
12)
I QUICKART
2000W ARNING & SAFETY NOTES
,I
Do not drive over curbs or the edges of hardened surfaces higher than one'inch.
. ,.-
Always look behind the QuicKmi before and while operating in nwerse.
Ba"tieries must be'fully charged initiaily berore using the QuicK,art.
The electrolyte in a storage battery is an acid, which can cause severe Jmrns to
, the sldnandeyes. Wear appropriate protectivedothingwhen woiIring with
,batteries.' Treat all el~Ctrolyte spills Withi~n extendedfiushing with dtJ'l.r water.
Contact a physician immediately If contaCt is made-Mthbattery lidil. ,,',
13) , ' Sta11dard batteiies do requiTe regular maintenance. It may be llece'ssa:ry to add
distilled water to the batteries.
,'.
14)
Hydmgen gas is fonned when charging the batteries. ,Use a1ocati6nwith adequate
ventilation when charging QuicKart batteries.
Never smoke near batteries. Do ngt
charge batteries in an area with openflaine' or wherethel
ie
is 6!ectrical equipment
that could cause an electrical arc.
.....
15)' Do n6tlay metiil6bjects(wrenches, screwdtivets,etc.) on any of the batteries to
'prevent electrical short circuits.'" ", ,
16) Batteries are heavy. Always use care and proper lifting technique to avoid injury
when removing otreplacirig'batterie~. . , ' " , .'
17) 'Make sure Qt:dcKart is properly secured'vvhen changing tit'es;' (See instruCtions on
'pages 30+30
18) Two options are available to tether the carts together, a strap or a cart, restraint
. 'assembly. These'are available as accessories.'To view the procedure to' strap the carts
, ,,' see the illustration on pages 6+7. The cat): restraint assembiy aisohas a"strap and,
adds a sptirig to allow some motion afthe carts itt tumsbut stili controlsthem.
DANE INDUSTRIES, INc. QUICKART 2000 OWNER'S MANuAL 2
5400 NathanLaneN, , Suite 150, Plymouth, MN 55442 / 888-544-7779 / 763-544-7779 / Fax [phone]
WWW.DANElNDUS1RIES.COM

f
t.:'INNt;M>.CU"l;
~:N,~E$Q'L\,J.I~i\
..e t f!
f'UlL:'TI:\
rt~r:"'f("'k~!
~.
RiOMOTiO
1'.iB~-~m~,,;;w"tJM
7ib'.sh.'ir~ oot..Ei~ ih.-us/>.
50D-](J2
50.0-0.40
500.-10"1
600.-b48 OR. 500-122
DANE INDUSTRIES, INc.
QUICKART 2000 LABELS
500-049
E(v1ERGENCY
SHUTOFF
500-128
500-021
5(lO-041
500-042
. WA~RANri
V,dID •
IF: s:w IS
BROKEN
50.0.-0.91
!J:IJ)li~;;::_. __ S'f!f,,*"~ __ .~:q
B~JTI.ote_ -an.d .auh;}?!,<RlI)lI1S.t -~e' re-prQgfa,mmed"
~fter.~/laJlgi!\g ~at1eTies,
~WIDfY]ili~~?~bt~~~~
War~n!ywIil b-e VPiO-lf fhiscayer'[;i~Il1OVef!.
There-llre no operalqrserJ!ceab!e palls insIde.
5.oQ-125
TmE QU/oKART2000 "LABELS, MANUAL
DYIG.DATE {f/29!63
O.X '" :1.0:.1.00
a.xx '" :£0;030
O.XXX ;., ±O;oos
·ANGLE ..... £f· .
s;H
EET
fOF1
QUICKART 2000 OWNER'SMANDAL 3
5400NathanLane N. , Suite 150, Plymouth, MN 55442 I 888-544-7779 I 763-544-7779 I Fax[phone]
WWW.DANEllIDUS1RlES.COM
I

I QUICKART 2000
LABEL LOCATIONS
. i
DANE INDUSTRIES, INc. QUIcKART2000 OWNER'sMANuAL 4
5400 Nathan Lane N. , Suite 150, Plymouth, MN 55442 / 888-544-7779 / 763-544-7779 / Pax 763-544-4234
-WWW.DANEINDUS1RIES.COM
I
500-102
.500-039

¥:
o
o
I
i
~
co
~.
~
U<
.0
f
iJ3'
i:1~
~::::
~;;
8-
~gg
'" '
• U<
0",
0.0.
~ -~
..,
..,
""
- ..,
'"
'f
U<
"'
.0.
.:.,
..,
..,
""
-
en
~
--.l
8l
,
'-"
"'
~
""
o
~
I
!f1
~
10
~
~
N
o
o
o
o
I
til
f
V>
TIE STRAP TO LAST
CART HANDLEBAR.
o
L-PLACE CONTAINER IN 'CART
. TO HOLD LOOSE STRAP:
MOVING STRAP AFTER ADDING CARTS:
A. RELEASE STRAP LATCH WITH ONE HAND TO ALLOW STRAP TO SLIDE.
S. WITH OTHER HAND, REMOVE HoOK FROM HANDLEBAR AND MOVE TO ADDED CART(S).
C. LET GO OF LATCH. WHILE STILL HOLDING HOOK, PULL LOOSE END OF STRAP TO TIGHTEN.
REMOVING CARTS:
A. RELEASE STRAP LATCH WITH ONE HAND TO ALLOW STRAP TO SLIDE.
B. WITH OTHER HAND, P:EMOVE HOOK FROM HANDLEBAR.
C. LET GO bF LATCH. WHILE STILL HOLDING HOOK, PULL LOOSE END OF STRAp
REPEATEDLY TO SHORTEN STRAP WHILE WAU<ING TOWARD QuicKART.
D. HOOK LATCH AND HOOK ASSEMBLY TO SlOE OF LAST CART.
E. STARTING WITH THE STRAP END, SUNCH UP LOOSE STRAP AND PLACE IN CONTAINER.
rO
S
(l
~
~
N
o
o
o
(l
~
~
~
>
(l
Q
(!)
(!)
o
~
r-<

STEEL CABLE
~
DANE lNDUSTRIES,INC.
0;
II
"
I!
!
"
"
II
r
II
I
I
100-140 Cart Restraint
with cable
/
"
i!
QUICKART~
fl
II
"
II
n 400-00&5/16018 BOLT
(4)
(1/2" SOCKET REQ'D)
. ---- ~
/ '
~
."A . 22.0-0.45 SUPPORT
" '.' .
/ ".····-7 --0- .•.. _.- ..... - .. _.--.--:1;. ='==91'----,(
\,_~// CD
". ~
o
~ '--""-----
L..cJ_j-' --- ______ _
I
°1
'-V BOLT-HOLE AT BOTTOM
n···.
400-142.7fI6-14 x 4" LG ...... ~.
BOLT: 410-0147/16-14
. (5/8" SQCKE.T REQ'D)
.. ' .. LOCK-NUT
(i1II6" SOCKET REQ'b)
DANE lNDUSTRIES Ino,
5400 Nathan Dme N. #150
Plymouth, "MN 55442
TITLE
PHONE: [phone]
FAX: (763)'544-4234
CART RESTRAINT - ASSEMBL Y
DWGiPART NO. SCALE 1/8 SHEET 2
OF 2
QUIcKART2000 OWNER'sMANUAL 6
. 5400 Nathan Lane N. , Suite 150, Plymouth, MN 55442 I 888-544-7779 ! 763-544-7779 ! Fax [phone]
WWW.DANEllIDUSTRlES.COM

1
)
)
)
)
)
)
)
)
)
)
)
)
)
430-034
BUCKLE
. 10
~---q
~0
THIS HOOI< ATIAP'HES TO
LEAD SHOPPING CART
DANE INDUSTRIES, INC •.
REMOVE AND DISCARD HOOK o
'~ .. ··.o·.·.··
~
PASS SHOPFiIN(;j CART
-HANDLE BAR OVER CART.
R~STRAINT MAST"AS sHOWN.
(0 . /~~.~
ATTAcH SHOPPING l~jf---,--
CART TO YOKES ._
DANE INDUSTRIES Inc.
5400 Nalhan
lane N. #-150
Plymoulh, MN 55442
PHONE: [phone]
FAX; (763).544-4234
TITLE RELEASE ECO
CART RESTRAINT-ASSEMBlY 216
DWGIPART NO.
110-066 SCAl!=, 1/8 . ISHEET 1
OF 2
OWG DATE 1125102 MAT'L
QUICKART.2000
OWNER'S MANuAL 7
5400 Nathan LaneN. ,Suite 150, Plymouth,MN 55442 I 888-544-7779 I 763-544-7779 I Fax [phone]
WWW.DANEllIDDS1RlES.COM

I UNPACKING THE QllCKART 2000 I
1) The QuicKart 2000 is typically shipped on a wooden pallet. It comes with additional
components packaged inside the QuicKart. Care must be taken not to damage them
during the unpacking. The components
are:
2)
3)
4)
5)
6)
7)
8)
a) QuicKart,.thebasic electric machine with two keys,
b) A box
including: a Remote Control Transmitter, to remotely control the QuicKati,
and Cart CouplerHardware (yokes for the cart coupler).
Remove all the plastic film that is wrapped around the system componellts.Take care
not to bend
be.acon post components (especially the alltennas) whel} "l'ellloVing the
plastic. Cut banding material, which holds the QuicKati to the pallet. .
Raise the hood to fmd a small box containing the remote control, and cati coupler
hardware. Remove this box and set it aside.
To remove the QuiCKali from the pallet, use a sturdy wooden boat·.d( s) to create a ramp.
Remove all straps holding the QuicKart to the shipping pallet. Insert the key
and tum
on the QnicKar.t. Tum the twist grip slowly alld gnide the QnicKart forward, down the
ramp
to the floor.
Turn
OFF the QuicKart.
..
M:lke sure the machine is OFF, the Beacon post hinges from a center position on a bolt .
and nutah·eadyinlitilikd. "Swing it to all 11 :00 o~elock position. Remove the bolt at the
bottom
of the beacon post bracket. Swing open the QyicKart body by lifting it from the
. handl~ side. There isa white plug at the end of thebeacQn post, which is attached to a
cable that extends into the tube. Feed this plug thl'o
l1
gh the hole in the center of the
beacon post-mounting bracket. Pull gently on this plug and cable as you sti"aighten the
beacon post to a full vertical position. Replace the bolt in the bottom holes
and tighten
lightly. Use care not to damage the wires. Inseli the plug into the vacant junction box
socket located neat· the edge of the machine. Make sure the plug and socket orientations
are aligned. Take care not to damage the alltenna, lights or the cable connectors at the
ends
of this beaconpost.
To attach the cart coupler yokes, refer to the diagram on pages
17 or 18 ofthe Owner's
Mallual.
Each hand-held remote control trallsmitter operates on a unique pre-progratlUlled code.
For the QnicKati to operate in the RempteMode, the receiver, which is in the beacon
post, must be progratnnled to match the hand held transmitter. See page 28 for
directions on howto program the remote control transmitter.
DANE INDUSTRIES, INc. QUIcKART2000 OWNER'S MANuAL 8"
5400 NathanLane N., Suite 150, Plymouth, MN 55442 I 888-544-7779 I 763-544-7779 I Fax[phone]
WWW.DANElNDUSTRIES.COM

)
)
)
I.
QUICKART 2000
IMPORTANT MAINTENANCE NOTES
.. Check the QuicKart daiIy,for sarti·operation.
Im~roperuseoroperation of theQuicKart, orthelack ofprop~rpwintenanpe, may:!~suItin
debie~s.~d perfdpnance or damage.to the QuicKart' The foIloWlllg p1n1s . Of the' QriicI{art
needregu!dr.and routine maintenance.
.'. . .', ... ., .' .
'-,
1. Batteries c Add distilled wateras necessary. Water levels should be checkedmontl:J.ly.
-,j -,>C;'-·' ,'-' '- - ": .. ,.", , .,.- ':' •.. "
~". 1;'iJ.~,s .; TIres are solid(foam filied).CheckweekIy for wear.
.,,",
3. Rear Swivel Wheel Bearing -Grease evelY 6 months (grease gun compatible).
'-,:!'
If at any time the QuicKart does not operate correetIy,immediately.turn.:it.6ffand
remove the key to prevent further operation. Immediately report any malfunctions to
the
store 11lamlger resppnsibleforthe QuicKartandDane Industries at 1"888C544"7779 ..
! j)
. ,.
, ~ ',- \
..... ,' WARNING. ,.
--.-, -;-.::._,'1:'-'
Do not permit open flame;sparkSorsniOking .
during maintenance .
.' Adequate ventilation is essential forsafetyi.·
- .,,;, . __ ' '··~r--· I ' _ "_ _ _'.", - : . l", _ ." -"',,' - ' ,
'Do' nOt Iaymetal objects on the batteries.
DANE INDUSTRIES, INc.
QUICKART 2000
OWNER'S MANuAL 9 .
5400 NathanLane N" Suite 150, Plymoutb, MN 55442 / 888-544-7779 / 763-544-7779 / Fax [phone]
WWW.DANEINDUS1RIES.COM
'-i';:~

OVERVIEW OF OPERATION
I
The QuicKart is an electrically powered shopping cart collection machine. It has several
nnique and patented
f.ef1tnr~s,yvhicp allow it to.beus~d;s?:fely.andsimply in the shopping cart
collection
process." ...... .. '.. '. .'
TheQuicKartpmYide~ thb'
pushl1g
powerfora single empJoyee to' safelya~d .~asWYW~\re. a
maxiriiliinof 20'slioppidgcat'ts from the'parking lot into the store. Its abilitY t()6p~i~t~in
remote control mode allows a single employee to steer the cham of catiS from the 'fi'ontof the
cali line while controlling the QuicKati as it pushes and follows from behind.
The QuicKart has pi-oven its ability to work in all types of weatherrangmg fromexti'ehi~ heat
or cold to rain and snow. The QuicKali has operateddependably in winter weather as~old as.-
20 degrees. it will also plish caiis through loose snow. On packed snowthe QuiCKillt 2000
virill push 10 to 20 catis. Winter operation can be enhanced with the use of optional snowtires.
. ' ji_., ',-: . ,. I -"~";: ,.;0; " '" .: -, ', ... ".~': ." ."". ,
The QuicKart operates ou a 36-volt battery system. It will operate for up to ten hours on
a single charge. Cold
weather will reduce operating time. It will require eight to ten
hours to:fullycre"hargethe batteries. .., ..... 1 ..
Each 'hand-held cremote .. control transmitter.operateson a llnique precprogrammed'cOde.
For the QuicKart to operate in the Remote Mode, the receiver, which is ip. the beacon
post,
must be programmed to match the band held transmitter, seepage 27 for details.
The remote#poweredby'internalb:iitehe$"w!1ich shoullibedJ.ilrlgedevel·Y two months
for dependable operation. The smallllgh1/tiri' iheremote will cease to operate when the
battery needs replacing .. Nter.pattery,replacement, the cremote must be reprogl'ammed;
see page 28 for details.
The QuicKali is a productivity"enhancingtool; which will be .most ~ffective 0hen it is well
maintained and used responsiblY
.. Tr,"!iping.ofemployeesisyery .it):lP911flUt. PJease read and
review this m;:.mUa1.Westrotlglyre¢ollmend thafa:irainingahdoperatorcertificationprogratll
be developed and implementedto assure adequate training and safe operation.
The use of the Dane Industries' "Cati Depot" creates an integrated system for cart collection,
which enhal1ces productivity even finiher. Additional optional accessories for the QuicKali
are also available. These include an optional snowplow, snowtires and chains.
DANE lNDUSTRlES, INc •.
QUICKART 2000
OWNER'S MANUAL 10" '.
5400 NathanLane N. , Suite 150, PlymOUtll, MN 55442 / 888-544-7779 / 763-544-7779 / Fax[phone]
WWW.DANEINDUS1RlES.COM

)
)
)
)
)
)
)
)
)
)
)
)
)
)
)
I QUICKART2000 -
TOP VIEW
I
"FIBERGLASS BODY
.~, -.
-,:,- . PLER YOKE
STOP BUTTON
"",,:-., .;
THROTTLE GRIP
.. SYSTEM JUNCTION BOX •.
DANE INDUSTRIES, INC. QUICKART 2000 OWNER'S MANuAL 11
5400 Nathan LaneN. , Suite 150, Plymouth,MN 55442 ! 888-544-7779 ! 763-544-7779 ! Fax [phone]
WWW.DANEJNDVSTRlES.COM

~
o
o
Z
S.
~
r
~. ~
:z:
en
~' ~ ~
p
I
iF
tJ
~
~~ §~ s~ ~
~
~
,
•
U>
co"'
0",
Ii:
-:.,
--l
--l
'0
~
--l
0;
w
0-
f:
--l --l --l
'0
~
""
~
--l
0;
'f
U>
"' "'
,
~
"'
1:1
~ ~
e;J
>-3
~
!f1
It
r
I
N
<:>
<:> <:>
0
~
;:0
rli
i
,...
tv
t3
z
".t;
"' '"
R<>
;r.
.Ul
o
$.
,
:.~
,~
ifi
OON,l'ROL
PANEL
H10~03'$
PLW'GS·INTO
DANE
SUPPLIED-
.EKl'ENSION
CORD.,
7.0.0-1'1;5
I
:CHARGER
;81Q-625;>'$n25:"g~
8tO-Oi-2,'<Sh2592
KEY'S"'~¢HW1CA£L1;'
..
665-0:[5,
-.
C~ms%~~R
.':
}'~A1N,(~JNlI)
'~ASSE::MB:LED
MdJO.R
tijl~r:rF10L
AND
:.cONTACrQA.
PLATE
1"00-069'
rJ1
~ ~
;
o
~
~

J
)
)
)
)
)
)
)
)
)
)
· .. ·I-I _______ S_Y_S_T_E_M_JUN __ C_T_I_O_N_B_O_X ________ .......... _ ......... ;,
DIAGNOSTIC LIGHTS
SUPPLYFAUL T -_---,--_---~
REMOTE'BRAKE
REMOTE SLOW
~.,' .. ':' ,
RENlPTEF !,\ST
DRIVE COMMAND ~_---------.
LOw'VOLTAGE ---'-------- ______
HOUR METER _________ ~
ClnCUIT SIlEAKER ~~itJ
BATIERY (RED) ..
CHARGER(GRA~ ~.
CONTROLLER (BLACK) ......
-I; '.'_<_
""'-
-'-.
---".
£:... THROTILE
, .• '0;:1 CONTROL PANEL
®Iy ~~:.~o.~:.~~,~
... IT CONTROLLER
®D-- BRAKE COIL
&8WITCH·······
'----- HORN CONNECTOR
DANE INDUSTRIES, INC.
QUIcKART2000 OWNER'sMANuAL 13·
5400 NathanLane N. , Suite 150, Plymouth, MN 55442 / 888-544-7779 / 763-544-7779 / Fax [phone]
WWW.DANEINDUS1RIES.COM

11- ___ .,-Sy_ST_E_M_JUN __ C_T_I_O_N_B_O_X_D_IA_' _G_N_O_S_T_IC_L_IG_H_T_S __ ---....;...I: I
Supply Fault: There are two conditions which cause this diagnostic light to come on:
Remote Brake:
.'-'.'," "
Remote, Slow.:
Remote Fast:
1. When this light remains on (but not flashing) it indicates the mac1rine was
tumed <iff by pushing on the red emergency shutoffbuttotiollthe control
panel. The machine will
not function while the light is on. To reset, pullout
the button, tum the key switch off, then on again. This condition does riof
require service. (The key switch is the cOITect way to turn offthe,;maclrine'
when it is stored or set aside for periods oftime.) , '
2. When this light is flashing, it indicates
that there is a problem in either th~
beacon post or the control panel. In afault condition the "supplYfiill.t" light
starts flashing as soon as the machine is tumed on with the key switch. The,
machine will not function while the light is flashing. The controlpanel lights "
may remain lighted 'for 3-seconds then shut down but the faultlightwlll
remain flashing as lOIig as;the fault condition exists.
To detymrine if the proble111is in the beacon post, tum offthe machine with
the key switch, unplug the cabkiyading to the beacon post then tum the key
switch on again. If the problem is in the beacol1 post the machine will operate
noiwally but only in the ','manual" mode. If the Prpbkm is somewhere in the
coritrol panel circuitlY, the fault light will cont41u.e to flash and the pane!
lights will go offin about 3 seconds. "
~~~ lights to indicate presence of "Brake" c011llB~~ from receiver.
effe6t in manual mode."
It has no
LED lights to indicate presence of "Slow"drive command from receiver.
Must light in conjunction with "Drive" COllll1).and .LE\P in "Remote" mode in
order to operate machine. It has no effect in manual rnRde.
LED lights to indicate presence of "Fast" drive coll11riand from receiVer. Must
light
in conjunction with "Drive" ,co=and LEDm"Remote" mode in order
to operate machine. It has no effect inmanual mode. '
Drive Command: LED lights to indicate drive signal is being sent to motor control.
Low:
LED lights when battery voltage is too low to operate machine properly
(below approximately 27 volts).
Hour Meter:
Hour glass symbol blinks every ten seconds when drive co=and is present
to indicatethat meter is tinring machine operation.
DANE INDUSTRIES; INc. QUIcKART 2000
OWNER'sMANuAL 14
5400 NafuanLane N. , Suite 150, Plymoufu, MN 55442 / 888-544-7779 / 763-544-7779 / Fax [phone]
WWW.DANEmDUSTRJES.COM