Danfoss Link VISGX45X User manual

MAKING MODERN LIVING POSSIBLE
Danfoss Heating Solutions
Danfoss Link™ HR Hidden Relay
Installation Guide

2VISGX45X © Danfoss 04/2011
Installation Guide Danfoss Link™ HR

3
VISGX45X © Danfoss 04/2011
Installation Guide Danfoss Link™ HR
Installation Guide
Installationsanleitung
Guide d’installation
Installationsmanual
Installationshandbok
Asennusohje
Installatiehandleiding
Instrukcja instalacji
Instalační příručka
GB
DE
FR
DK
SE
FI
NL
PL
CZ

4VISGX45X © Danfoss 04/2011
Introduction ............................................... 5
Installation................................................. 6
Adding device ............................................. 7
Perform network test....................................... 8
Factory reset ............................................... 8
Trouble shooting........................................... 8
Technical specications .................................... 9
Disposal instructions ....................................... 9
Index
Installation Guide Danfoss Link™ HR

5
VISGX45X © Danfoss 04/2011
The Danfoss Link™ HR (Hidden Relay) is a device for switch-
ing heating elements or other electrical equipments ON/
OFF, either manually or by schedule.
LED
Install
buttons
Fuse
(including
spare fuse)
The Danfoss Link™ HR is powered by 230 V~ and shall
according to regulations be installed in a build in box or in
the wall box.
Introduction
GB
Installation Guide Danfoss Link™ HR

6VISGX45X © Danfoss 04/2011
Note! Do not install electric oor heating system without a oor
sensor, when the heating element is installed on or beneath
wooden surfaces and other surfaces sensitive to temperature!
Installation
The Danfoss Link™ wireless system’s transmission range is
sucient for most applications; however each building has
dierent obstacles aecting communication and maximum
transmission distance.
If communication problems occur Danfoss suggests that
accessories would be required to support the system, such as
repeaters. In exceptional cases the wireless system may not be
suitable for your installation.
Please be aware of the following, when installing Danfoss
Link™ HR:
Installation and placement must be according to
local building regulations.
Operation mode
Danfoss Link™ HR supports two types of operation modes:
1. ON/OFF switching.
2. Heating regulation: when using Danfoss Link™ HR as heat-
ing regulation in a room you also have to install a Danfoss
Link™ RS.
Installation Guide Danfoss Link™ HR

7
VISGX45X © Danfoss 04/2011
Installation
1. Danfoss Link™ HR is to be mounted
into a build in box in the wall.
2. It is recommended not to install
the HR in a metal box due to the
possible disturbance of the radio
communication.
3. Connect the Danfoss Link™ HR ac-
cording to the connection diagram.
Installation Guide Danfoss Link™ HR
L
N
GB
Adding Danfoss Link™ HR to a system is
made from the Danfoss Link™ CC Central
Controller.
When adding, press the install but-
ton until the LED gives a fast
green ash.
For further information,
see the Danfoss Link™ CC
instruction manual:
Conguration 6:
Adding devices.
Adding device
Max. 1 m

8VISGX45X © Danfoss 04/2011
Installation Guide Danfoss Link™ HR
When the Danfoss Link™ HR has
been added to the Danfoss Link™
CC Central Controller, a network test
should be performed.
For more information on network
tests, see the Danfoss Link™ CC
instruction manual:
Conguration 8:
Perform network test.
Perform network test
Green LED ON Relay OFF/Standby
Red LED ON Relay ON/Heating
Green LED fast ash Inclusion or link test
Red LED short ash Inclusion not OK
Link test not OK
Note: If the fuse has burned you can replace it with the spare
fuse, located in the fuse holder.
Trouble shooting
1. Hold both install buttons in front
of the device for approx. 5 sec. until
LED gives a red ash.
Factory reset

9
VISGX45X © Danfoss 04/2011
Installation Guide Danfoss Link™ HR
GB
Technical specications
Operation voltage 230 V AC, 50 Hz
Standby consumption <1W
Load 2300 W, 460 VA, 600 W
Incandescent Bulbs
Regulation PWM or ON/OFF
Ambient temperature 0˚ to +35˚C
Micro-fuse T 10 A H
Transmission
frequency 868.42 MHz
Transmission range in
normal buildings Up to 30 m
Transmission power Max. 1 mW
IP class 20
Dimensions 52 mm × 52 mm × 31 mm
Disposal instructions

10 VISGX45X © Danfoss 04/2011
Einführung................................................ 11
Installation................................................ 12
Hinzufügen von Geräten .................................. 13
Durchführen eines Netzwerktests ......................... 14
Rücksetzen auf Werkseinstellungen ....................... 14
Fehlersuche und -behebung .............................. 14
Technische Spezikationen................................ 15
Hinweise zur Entsorgung.................................. 15
Inhaltsverzeichnis
Installationsanleitung Danfoss Link™HR

11
VISGX45X © Danfoss 04/2011
DE
Das Danfoss Link™ HR (Unterputz-Relais) ist ein Gerät zum Ein-
und Ausschalten von Heizelementen oder anderen elektrischen
Geräten. Dies kann wahlweise manuell oder zeitgesteuert
erfolgen.
LED
Installations-
tasten
Sicherung
(inklusive
Ersatzsicherung)
Das Danfoss Link™ HR wird mit 230V~ betrieben und sollte
gemäß den Vorschriften in einer Unterputz- oder in einer
Aufputzdose montiert werden.
Einführung
Installationsanleitung Danfoss Link™HR

12 VISGX45X © Danfoss 04/2011
Hinweis! Wenn das Heizelement eines elektrischen Fußboden-
heizsystems auf oder unter Holzächen oder anderen tempe-
raturempndlichen Flächen montiert wird, muss in jedem Fall
ein Bodenfühler montiert werden!
Installation
Der Übertragungsbereich des Funksystems des Danfoss Link™
ist für die meisten Anwendungen ausreichend. Allerdings gibt
es in jedem Gebäude andere Hindernisse, die die Kommuni-
kation und den maximalen Übertragungsbereich beeinträch-
tigen.
Bei Kommunikationsproblemen empehlt Danfoss den Einsatz
von Zubehörteilen wie beispielsweise Verstärkern. In Ausnah-
mefällen ist das Funksystem für Ihre Installation möglicherweise
nicht geeignet.
Bei der Montage des Danfoss Link™ HR ist Folgendes zu
beachten:
Die Platzierung und Installation muss unter
Beachtung der örtlichen Bauvorschriften erfolgen.
Betriebsmodus
Das Danfoss Link™ HR unterstützt zwei Betriebsmodi:
1. EIN/AUS-Schalten.
2. Heizungsregelung: Wenn Sie das Danfoss Link™ HR für die
Heizungsregelung in einem Raum einsetzen, müssen Sie
zusätzlich einen Link™ RS von Danfoss montieren.
Installationsanleitung Danfoss Link™HR

13
VISGX45X © Danfoss 04/2011
DE
Installation
1. Das Danfoss Link™ HR muss in
einer Unterputzdose in der Wand
montiert werden.
2. Es wird davon abgeraten, das
Unterputz-Relais in einem Metall-
gehäuse zu montieren, da dies
die Funkverbindung des Gerätes
beeinträchtigen kann.
3. Schließen Sie das Danfoss Link™HR
von Danfoss gemäß dem An-
schlussplan an.
Installationsanleitung Danfoss Link™HR
L
N
Das Hinzufügen des Danfoss Link™ HR zu ei-
nem System erfolgt über den Zentralregler
Link™ CC von Danfoss.
Beim Hinzufügen die Installations-
taste gedrückt halten bis die
LED schnell grün aufblinkt.
Weitere Informationen
nden Sie im Produkthand-
buch zum Danfoss Link™ CC:
Konguration 6:
Hinzufügen von Geräten.
Hinzufügen von Geräten
Max. 1 m

14 VISGX45X © Danfoss 04/2011
Installationsanleitung Danfoss Link™HR
Wenn das Danfoss Link™ HR dem Zen-
tralregler Link™ CC von Danfoss hinzu-
gefügt wurde, sollte ein Netzwerktest
durchgeführt werden.
Weitere Informationen zu Netzwerk-
tests nden Sie im Produkthandbuch
zum Danfoss Link™ CC:
Konguration 8:
Durchführen eines Netzwerktests.
Durchführen eines Netzwerktests
Grüne LED EIN Relais AUS/Stand-by
Rote LED EIN Relais EIN/Heizung
Grüne LED blinkt
schnell
Einbindung oder
Verbindungsprüfung
Rote LED blinkt
kurz
Einbindung fehlgeschlagen
Verbindungsprüfung fehlgeschlagen
Hinweis: Sollte die Sicherung einmal durchbrennen, können
Sie diese durch die Ersatzsicherung im Sicherungshalter
ersetzen.
Fehlersuche und -behebung
1. Halten Sie beide Installationstasten
an der Vorderseite des Gerätes
etwa fünf Sekunden lang gedrückt,
bis die LED rot zu blinken beginnt.
Rücksetzen auf Werkseinstellungen

15
VISGX45X © Danfoss 04/2011
DE
Installationsanleitung Danfoss Link™HR
Technische Daten
Betriebsspannung 230 V AC, 50 Hz
Stromverbrauch im
Stand-by-Modus <1 W
Last 2.300 W, 460 VA, 600 W
Glühlampen
Regelung PWM oder EIN/AUS
Umgebungstemperatur 0 ° bis +35 °C
Mikrosicherung T 10 A H
Übertragungsfrequenz 868,42 MHz
Übertragungsbereich in
normalen Gebäuden Bis zu 30 m
Übertragungsleistung Max. 1 mW
IP-Schutzart 20
Abmessungen 52 mm × 52 mm × 31 mm
Hinweise zur Entsorgung

16 VISGX45X © Danfoss 04/2011
Introduction .............................................. 17
Installation................................................ 18
Ajout d’une unité.......................................... 19
Réalisation d’un test du réseau ............................ 20
Réinitialisation aux réglages d’usine ....................... 20
Dépannage ............................................... 20
Spécications techniques ................................. 21
Consignes de mise au rebut ............................... 21
Sommaire
Guide d’installation Danfoss Link™ HR

17
VISGX45X © Danfoss 04/2011
FR
Le relais intégré Danfoss Link™ HR est un dispositif d’activation
et de désactivation manuelles ou programmées des éléments
chauants ou d’autres équipements électriques.
LED
Boutons
d’installation
Fusible
(avec
fusible de
rechange)
Le Danfoss Link™ HR est alimenté sur 230V~ et doit, confor-
mément aux réglementations, être installé dans un boîtier
encastré ou un boîtier mural.
Introduction
Guide d’installation Danfoss Link™ HR

18 VISGX45X © Danfoss 04/2011
Remarque : n’installez pas de système de chauage au sol
électrique sans sonde de dalle si l’élément chauant est
installé sur ou sous des surfaces en bois ou d’autres surfaces
sensibles à la chaleur!
Installation
La portée de transmission du système sans l Danfoss Link™
sut pour la plupart des applications. Chaque bâtiment pré-
sente toutefois diérents obstacles susceptibles d’aecter la
communication et la distance de transmission maximale.
En cas de problèmes de communication, Danfoss préconise
l’emploi d’accessoires tels que des répétiteurs. Dans de rares
cas, il est possible que des installations ne se prêtent pas à
l’utilisation d’un système sans l.
Lors de l’installation du Danfoss Link™ HR, veuillez tenir
compte des points suivants:
L’installation et le positionnement doivent être
conformes aux réglementations en vigueur.
Mode de fonctionnement
Danfoss Link™ HR prend en charge deux types de modes de
fonctionnement:
1. Marche/Arrêt.
2. Régulation du chauage: si vous utilisez le Danfoss Link™
HR comme système de régulation du chauage dans une
pièce, vous devez également installer un Danfoss Link™ RS.
Guide d’installation Danfoss Link™ HR

19
VISGX45X © Danfoss 04/2011
FR
Installation
1. Le Danfoss Link™ HR doit être
monté dans un boîtier encastré
dans le mur.
2. Il est fortement recommandé de
ne pas installer le Danfoss Link HR
dans un boîtier métallique an de
ne pas perturber les signaux émis
par le système.
3. Branchez le Danfoss Link™ HR en
respectant le schéma de branche-
ment.
Guide d’installation Danfoss Link™ HR
L
N
L’ajout du Danfoss Link™ HR à un système se
fait à partir du régulateur central Danfoss
Link™ CC.
Lors de l’ajout, appuyez sur le bou-
ton d’installation jusqu’à ce
que le voyant vert clignote
rapidement.
Pour plus d’informations,
voir le mode d’emploi du
Danfoss Link™ CC:
Conguration 6 :
Ajout d’unités locales.
Ajout d’une unité
1 m max.

20 VISGX45X © Danfoss 04/2011
Guide d’installation Danfoss Link™ HR
Il convient d’eectuer un test du
réseau une fois le Danfoss Link™ HR
ajouté au régulateur central Danfoss
Link™ CC.
Pour de plus amples informations
sur les tests de réseau, voir le mode
d’emploi du Danfoss Link™ CC:
Conguration 8:
Réalisation d’un test du réseau.
Réalisation d’un test du réseau
Voyant vert allumé Relais arrêté ou en veille
Voyant rouge allumé Relais actif/Chauage
Clignotement rapide du
voyant vert Test d’inclusion ou de liaison
Clignotement rapide du
voyant rouge
Inclusion incorrecte
Test de liaison incorrect
Remarque : Si le fusible a grillé, vous pouvez le remplacer par
l’un des fusibles de rechange situés dans le porte-fusible.
Dépannage
1. Appuyez sur les deux boutons
d’installation situés à l’avant du dis-
positif pendant environ 5 secondes
jusqu’à ce que le voyant rouge
clignote.
Réinitialisation aux réglages d’usine
Table of contents
Languages:
Other Danfoss Relay manuals