Danfoss RET B + RF Operating instructions

RET B + RF
Dial setting thermostat with LCD display
User & Installation Instructions

2
F
D
ES
DK
NL
G
P
LT
I
Installation Instructions 3-8
User Instructions 9-11
Instructions d’installation 12-17
Instructions d’utilisateur 18-20
Installationsanweisungen 21-26
Inbetriebnahme-Instruktion 27-29
Instrucciones de instalación 30-35
Instrucciones del usuario 36-38
Instruktions vejledning 39-44
Brugervejleding 45-47
Installatie handleiding 48-53
Instructiesevoor Gebruik 54-56
Ïäçãßåò åãêáôÜóôáóçò 57-62
Ïäçãßåò ÷ñÞóçò 63-65
Instrukcja instalacji 66-71
Instrukcja Użytkownika 72-74
Montavimo instrukcijos 75-80
Informacija Vartotojui 81-83
Istruzioni per l’uso 84-89
Istruzioni per l’utente 90-92

3
Installation Instructions GB
Features RET B (RF) / RET B-LS (RF) / RET B-NSB (RF)
Contact rating 10 - 230 Vac, 3 (1) (excl. North America)
Contact rating (N.America) 10 - 24 Vac, 50/60Hz, 3(1)A
Temperature Accuracy ±1°C
Contact Type SPDT Type 1B
Transmitter frequency 433.92 MHz (RF models)
Transmitter range 30m max (RF models)
Power Supply 2 x AA/MN1500 alkaline batteries
Control Pollution Situation Degree 2
Rated Impulse Voltage 2.5 kV
Designed to meet BS EN 60730-2-9 (EN 300220 for RF)
Ball Pressure Test 75°C
Temperature Range 5-30°C
Dimensions (mm) 85 wide x 86 high x 42 deep
Important note RF products: Ensure that there are no large metal objects, such as
boiler cases or other large appliances, in line of sight between the transmitter and
receiver as these will prevent communication between thermostat and receiver.
GB - Installation Instructions

4
Mounting
Fix at a height of 1.5m
approx from the floor,
away from draughts or
heat sources such as
radiators, open fires or
direct sunlight.
GB - Installation Instructions

5
Wiring (not RF models)
RET-B (3050 12/01)


GB - Installation Instructions

6
DIL switch settings
Heating selection
Slide the DIL switches to the
settings required (see below)
Cooling selection
COOL
ON/OFF
6 CYCLES
°F
COOL
NO DELAY
4 MIN DELAY
°F
HEAT
CHRONO
3 CYCLES
°C
HEAT
2 MIN DELAY
°C
ON/OFF - boiler switches
ON when below set
temperature and OFF when
above
CHRONO - energy saving
feature which fires the
boiler at regular intervals to
maintain a set temperature,
achieving a constant
ambient environment for
the user.
use 6 Cycles for radiator
systems
use 3 Cycles for
underfloor heating
GB - Installation Instructions
COMPRESSOR
DELAY

7
GB - Installation Instructions
Receiver Wiring (RF only)
RX1 & 2 (3055 12/01)
COM
RX3 (3056 12/01)
RX1 & RX2 RX3
NB. For mains voltage operated systems, link terminal 2 to mains live supply
Locking & Limiting

8
Commissioning (RF only)
Step 1 RET B-RF
Remove dial, press & hold
LEARN button for 3 seconds
(located under setting dial).
Do not replace the setting dial yet
NOTE: Thermostat now transmits
signal continuously for 5 mins
Step 2 RX1
Press and hold buttons PROG and CH1 until
green light flashes.
Step 3 RX2/RX3
For RX2 or RX3 repeat steps 1 and 2 for each
thermostat and channel, leaving at least 5 mins
between the commissioning of each thermostat.
Step 4 RET B-RF
Replace thermostat setting dial.
LEARN
GB - Installation Instructions

9
User Instructions
GB
Display
The LCD displays actual room temperature until the
setting dial is moved.
Setting the temperature
Turn setting dial to required temperature. The selected
temperature will flash in the LCD to signify it is showing
set temperature.
After a short period the display stops flashing and shows
actual room temperature.
Thermostat status (heat mode only)
A flame symbol will be lit whenever the thermostat is
calling for heat.
GB - User Instructions

10
Thermostat status (cool mode only)
A snowflake symbol will be lit whenever the thermostat is
calling for cooling. If this is seen to flash, the thermostat output
is delayed for a short period to prevent compressor damage.
Low battery indication
A battery symbol will flash in the display when batteries
require replacement. Batteries should be replaced within
15 days, after which the thermostat will turn off the load it is
controlling. When this happens “Of” will be displayed.
IMPORTANT: alkaline batteries must be used
GB - User Instructions

11
RET B-LS model only
This model is fitted with an Auto/Off switch.
When the switch is set in “I” position the thermostat
controls at the temperature set by the setting dial.
When set to “O” the thermostat output is turned off
and “Of” is displayed.
RET B-NSB model only
This model is fitted with a “Day”/Night switch.
When the switch is set to the “Sun Symbol”, the
thermostat controls at the temperature set by the
setting dial.
When set to the “Moon symbol”, the thermostat controls at
4°C below the temperature set by the setting dial.
NOTE: if used to control cooling, thermostat controls 4°C
higher, with switch in MOON position
GB - User Instructions