Danfoss TP7001 series User manual

TP7001
User Instructions
Accepting the Factory Pre-settings Weekdays (Mon-Fri) Weekend (Sat-Sun)
Event Time Temp °C Event Time Temp °C
1 06:30 20 1 07:30 20
2 08:30 15 2 09:30 20
3 11:30 20 3 11:30 20
4 13:30 15 4 13:30 20
5 16:30 21 5 16:30 21
6 22:30 15 6 22:30 15
Before programming the thermostat, press the recessed
RESET button to reset, using a non-metallic object (Fig.2)
Fig.1
Fig.2
Press and hold V & - until display changes (Fig.3)
Selecting the temperature display (°C or °F)
Selecting the clock display (am/pm or 24 hr)
Setting the Clock & Day
Fig.3
Press and hold Λ & + until display changes (Fig.4)
Fig.4
The date and time are set in the factory and therefore it
will not normally be necessary to do this on site. Changes
between summer and winter time are handled automatically
by the unit.
Setting the date: Press and hold Λ & PROG buttons for 3
seconds, to display date. (Fig.5)
The YEAR number will ash, use Λor Vto correct the year
(Fig.6)
Use - or +to move to MONTH, then use Λor V to correct
month (Fig.7)
Use - or +to move to DATE, in month then use Λor V to
correct day (Fig.8) The day of the week is set automatically
from the date.
Setting the correct time
After setting the date press PROG to display the time.
Use -or +buttons to set the correct time. (Fig.9) When time
is correct press PROG to return to RUN mode.
Y
our TP7001 comes ready programmed with a set of
operating times and temperatures. (Fig.1)
To accept these settings close the front cover and after
2 minutes these will be accepted automatically.
If you
prefer, you can change any of these settings using the
following instructions.
Fig.5
Fig.6 Fig.7 Fig.8 Fig.9
Thermostat mode either 7-day, 5/2 day or 24 hour
To check which mode your unit is set to press PROG until
Event 1 ashes in display.
• In 7-day mode only one day of the week is shown in
the display.
• In 5/2 day mode either weekdays or weekend days are
shown in the display
• In 24 hour mode no days of the week are shown in
the display.
Press PROG to return to RUN mode.

Danfoss Ltd
Ampthill Road
Bedford, MK42 9ER
Tel: [phone]
Fax: [phone]
Email: [email protected]
Website: www.heating.danfoss.co.uk
CURRENT TEMPERATURE
PROGRAMMED TEMPERATURE
TIME
Days of Week (Numbers or Text)
DISPLAY
Programming in 5/2 day mode
a) Press PROG button until Event 1 ashes, then press the DAY button
until display shows weekdays (Fig.13)
b) Follow steps b as above (on 7 day mode) to programme times and
temperatures for weekdays (Fig.14)
c) Press the DAY button to programme events for weekend (day 6-7)
or press the COPY button to repeat weekday programme.
To return to RUN mode, press and release the PROG button. The
display will change to show the current time, the set temperature and
actual temperature (Fig.15)
Fig.13 Fig.14 Fig.15
Programming in 24 hour mode
a) Press PROG button until Event 1 ashes (Fig.16)
b) Amend the time and temperature as follows:
1. Use the +or - buttons to change the time
2. Use the V or Λ buttons to change the temperature in 0.5°C steps
3. Press the NEXT button to move to the next event (Fig.17)
4. Repeat the steps above for the remaining events
c) When all events are programmed press the PROG button to return
to RUN mode (Fig.18)
Fig.16 Fig.17 Fig.18
Programming in 7 day mode
a) Press PROG unit Event 1 ashes (Fig. 10)
b) Change the time and temperature as follows:
1. Use the +or -buttons to change time
2. use the s or tbuttons to change the temperature
3. Press NEXT to set up next Event for the day
4. Repeat steps 1-3 for the remaining events (Fig.11)
c) When all events are correct, press DAY to programme events for the
next day. If you wish to repeat the times and temperature to another
day of the week then the COPY function can be used.
To return to RUN mode, press and release the PROG button. The
display will change to show the current time, the set temperature and
actual temperature (Fig.12)
Fig.10 Fig.11 Fig.12
Flame: shows when heating output is on
Battery: ashes when battery voltage is low
Hourglass: shows during programming delays or when
Delayed Start is active
Padlock: indicates keyboard lock
Suitcase: Holiday Mode
House and Thermometers:
Indoor and Outdoor Temperature
Clock and Hand: Timed and Manual Modes
Alarm: Alarm active
Frost Shield: Frost Mode
Λ Up Arrow: Temperature override up
Auto Mode (6 events per day)
Auto Mode (4 events per day)
Auto Mode (2 events per day) or All Day Mode
V Down Arrow: Temperature override down
OFF: Thermostat (O ) Mode
+ HRS: Extend function
KEY TO SYMBOLS