Danfoss WT-DR User manual

1 Installation Steps
The User Guide can be downloaded from: heating.danfoss.com.
1. Installation must be done by an authorised electrician.
2. The room thermostat should be installed at approx. 1.5 m
above floor and where the effects of sunlight, draught or oth-
er heat sources (eg. TV's) are avoided. See illustration 1.
3. First of all, carefully remove the cover. See illustration 2.
4. Connect the wire before mounting the back plate to the wall
box using the enclosed screws. Then mount the cover to the
back plate. See illustration 3.
2 Wiring
1. Dimensions (see ill. 4).
2. Wiring diagram (see ill. 5, S1, S2: floor sensor terminals; A1,
A2: volt-free auxiliary relay terminals, e.g. boiler).
3. WT-D/P is often used with Danfoss TWA actuator. Depending
on the conditions of power location and actuator type (NC or
NO), the wiring between room thermostat and actuator is dif-
ferent. Follow the illustrations to complete the wiring:
1. When power supply location is close to room thermo-
stat:
▪Connect to actuator TWA 230 V NC type (see ill. 6).
▪Connect to actuator TWA 230 V NO type (see ill. 7).
2. When power supply location is close to actuator:
▪Connect to actuator TWA 230 V NC type (see ill. 8).
▪Connect to actuator TWA 230 V NO type (see ill. 9).
3 Error Codes
Item Display Description
1 E1 room sensor failure
2 E2 floor sensor failure
4 Notes
1. Correct wiring is essential; using instrument to confirm L and
N before wiring is recommended.
2. Don't remove too much of the insulation cover from the wire
to avoid short circuit caused by the naked wire touching the
metal 86 size mounting wall box.
3. Don't let the screw press or touch the wire when using screw
to fix room thermostat in wall box. A short-circuit risk exists if
the wire insulation cover is damaged by the screw, and if the
naked wire connects with the screw.
4. If walls must be painted, mount the room thermostat after
painting, to avoid dust or paint material penetrating the
room thermostat and thus damaging the PCB.
5. The max load of relay is 3 A (resistive) or 1 A (inductive, such
as pump, motor). The relay will be damaged if the load ex-
ceeds the limit.
6. Don't cover the thermostat, for instance by hanging towels
directly in front of it.
7. The room thermostat should be connected to the corre-
sponding loop actuator in individual room temperature con-
trol.
5 Technical Specification
Feature Description
Approval CE Marking, EN60730
Ambient temperature -10 ℃ -60 ℃
IP class 30
Max load, inductive <1 A
Max load, resistive <3 A
Feature Description
Power consumption 2 W
Power supply 85-250 Vac, 50/60 Hz
Room temperature set range 5 ℃ -35 ℃
Floor temperature set range 20 ℃ -45 ℃
Shell material ABS + PC
Installation Guide
WT-DR/PR Installation Instruction
Danfoss Heating Solutions VICUK102 1

6 Illustrations
Illustration 1
Illustration 2
Illustration 3
Illustration 4
Illustration 5
Illustration 6
Illustration 7
Illustration 8
Illustration 9
Installation Guide WT-DR/PR Installation Instruction
VICUK102 Danfoss Heating Solutions
2

Installation Guide WT-DR/PR Installation Instruction
Danfoss Heating Solutions VICUK102 3

Installation Guide WT-DR/PR Installation Instruction
Danfoss A/S
Heating Solutions
Haarupvaenget 11
8600 Silkeborg
Denmark
Phone: [phone]
Fax: [phone]
Email: [email protected]
www.heating.danfoss.com
Danfoss can accept no responsibility for possible errors in catalogues, brochures and other printed material. Danfoss reserves the right to alter its products without notice. This also applies to products
already on order provided that such alterations can be made without subsequential changes being necessary in specifications already agreed. All trademarks in this material are property of the respective
companies. Danfoss Heating Solutions and the Danfoss Heating Solutions logotype are trademarks of Danfoss A/S. All rights reserved.
VICUK102 Produced by Danfoss Heating Solutions © 07/2014