Danfoss TP7001 series User manual

TP7001 Range
Electronic 7 Day
Programmable Room Thermostat
Danfoss Heating Installation Guide

TP7001
2
For a large print version of these instructions
please call Marketing on 0845 121 7400.
Danfoss can accept no responsibility for possible errors in catalogues, brochures, and other
printed material. All trademarks in this material are property of the respective companies.
Danfoss and the Danfoss logotype are trademarks of Danfoss A/S. All rights reserved.
®
Certification Mark

Danfoss Heating 3
GB
GB
Index
1.0 Installation Guide................................................................................4
2.0 System Overview .................................................................................4
3.0 Installation..............................................................................................5
3.1 Removing the wallplate.............................................................5
3.2 Installation considerations........................................................5
3.3 Axing the backplate.................................................................5
3.4 Wiring ...............................................................................................6
3.5 Batteries ...........................................................................................6
3.6 Tamperproof operation..............................................................7
3.7 Mounting the unit........................................................................7
3.8 Unit startup.....................................................................................7
4.0 Installer Advanced Programming Options .............................7
4.1 Service Interval Timer .................................................................7
4.2 Entering Installer Advanced Programming ........................8
5.0 Reset Procedure ................................................................................ 17
5.1 Partial Reset................................................................................. 17
5.2 User Reset..................................................................................... 17
5.3 Installer Reset.............................................................................. 17
Installation Instructions
TP7001 Range
Electronic Programmable Room Thermostat

TP7001
4
GB
GB
Thermostat Features TP7001 TP7001M
Power supply 2 x AA/MN1500/LR6
alkaline batteries 230V ± 15% 50Hz
Memory backup Retained for the life of the product
Factory set calendar clock Automatic summer/winter time change
Switching action of output relay 1 x SPDT, Type 1B
Switch rating of relay contact 3(1) A, 10-230 Volts
Remote sensor inputs
Up to three remote sensors, which can be
set by the installer for remote temperature
sensor, limit sensor, outdoor sensor, window
contact or telephone activated switch
contacts
Rated Impulse Voltage 2.5 kV
Dimensions (mm) 140 wide x 91 high x 28 deep
Ball Pressure Test 75°C
Temperature Range 5-30°C
Design Standard EN 60730-2-7
Control Pollution Situation Degree 2
Time accuracy ± 1 minute per month
Temperature accuracy ±1°C
1.0 Installation Guide
2.0 System Overview
Please Note:
This product should only be installed by a qualied electrician or
competent heating installer and should be in accordance with the
current edition of the IEEE wiring regulations.

Danfoss Heating 5
GB
GB
3.1 First remove the wallplate from the back of the unit.
3.2 From the top left hand corner of the wallplate, there must be
clearances of at least 21mm to the right, 21mm to the left, 36mm
above and 106mm below in order to mount the plug-in module.
3.3 Fix the TP70001/TP7001M and its optional remote room sensor
at a height of approximately 1.5m from the oor, away from
draughts or heat sources such as radiators, open res or direct
sunlight.
3.0 Installation

TP7001
6
GBGB
3.4 For wiring connections please refer to the diagrams below:
Battery Version
Mains Powered Version
The TP7001 and TP7001M can incorporate three inputs/sensor
types by using input b, C and d.
The sensor types are as follows:
1) Remote room temperature sensor (sold as an accessory).
2) Limit sensor, for example, oor temperature sensor (sold as an
accessory). Note: F10 in display - The underoor temperature has
exceeded the threshold temperature.
3) Outdoor sensor (sold as an accessory).
4) Window contacts, card reader contacts or teleswitch contacts.
Note: See Installer Advanced Programming Options for set-up
instructions.
3.5 For the TP7001 battery version, insert the batteries – making sure
that they are correctly oriented.
1234
bCdS COM
Room/outdoor/limit
sensor or contact
567
HTG
OFF
HTG
COM
HTG
ON
1234
bCdS COM
56789
10
Power Supply
HTG
COM
HTG
ON
HTG
OFF
LN
Z
Y
X
X, Y and Z can be connected to
Room/Outdoor/Limit Sensor or contact

Danfoss Heating 7
GBGB
ON
Keyboard Enabled
Reset Enabled
OFF
Keyboard Disabled
Reset Disabled
SW. No
SW.1
SW.2
3.6 The unit can be made tamperproof if required by setting the
DIL switches which will disable the keyboard, and/or the reset
functions. The DIL switches are located on the back of the unit.
3.7 Mount the unit on the wallplate
3.8 With the unit powered up, it is recommended to press and release
the RESET button to start up the TP7001 unit.
The TP7001 incorporates a number of advanced features which
can be set by the user. These are accessed via the User Advanced
Programming Mode, please refer to User Advanced Programming
in the User Instructions for details.
The TP7001 incorporates an additional number of advanced features
which can be set by the installer to improve the operating eciency
of the system and where required, to change the user functionality
of the product. These are accessed via an Installer Advanced
Programming Mode. These settings are optional and need only be
accessed if there is a demand for the enhanced functions.
4.0 Installer Advanced Programming Options
4.1 Service Interval Timer
Instructions on how to access this feature are available from our
customer support desk. Please note these are only issued to boni-de
heating installers.
Note: Always switch
the mains o rst
and never t/remove
the thermostat to/
from a live wallplate.

TP7001
8
GB
Option 30 - Set Temperature Upper Limit
This allows the upper limit of the thermostat setting
range to be limited. Press +until Option 30 is
displayed, use Vor Λto select required setting.
Can be set to any value between 40.0°C and 5°C in
0.5°C steps
Factory setting = 30°C
4.2 Entering Installer Advanced Programming
To access the Installer Advanced Programming Mode
follow the steps below:
a) Press and hold Vand PROG for 3 seconds to enter
User Advanced Programming, the display will
change to look like the image opposite.
b) Press and hold V, Λand PROG for 5 seconds to enter
Installer Advanced Programming, the display will
change to look like the image opposite.
c) Use the +and -keys to scroll backwards and forwards
between options then the Vand Λkeys to change
the option settings. The ashing digits in the centre
of the display indicate the number of the selected
option. The large characters in the top or bottom of
the display indicate the option value selected.
d) To return to RUN, press and hold PROG until the display returns
to previous RUN mode.

Danfoss Heating 9
GB
Option 31 - Set Temperature Lower Limit
This allows the lower limit of the thermostat setting
range to be limited. Press +until Option 31 is
displayed, use Vor Λto select required setting.
Can be set to any value between 5.0ºC and 40.0ºC in
0.5ºC steps
Factory setting = 5ºC
Option 32 - Enable O at Lower Limit
This enables an OFF function to be selected if a set
point below the lower limit is selected. Press +until
Option 32 is displayed, use Vor Λto select required
setting.
0 = Disabled
1 = Enabled (Factory setting)
Option 33 - Enable On at Upper Limit
This enables an ON function to be selected if a set
point above the upper limit is selected. Press +until
Option 33 is displayed, use Vor Λto select required
setting.
0 = Disabled (Factory setting)
1 = Enabled
Option 34 - Select On/O or Chrono-Proportional
This allows the thermostat to be set to run in On/O
mode or for a chrono-proportional cycle rate to be
selected. Press +until Option 34 is displayed, use Vor
Λto select required setting.
0 = On/O
3 = 3 cycles/hour
6 = 6 cycles/hour (Factory setting)
9 = 9 cycles/hour
12 = 12 cycles/hour

TP7001
10
GB
Option 35 - Set Integration Time
(Option 34 set to 3, 6, 9 or 12)
This adjusts the integration time of the PI algorithm to
increase control accuracy. It is only active if Option 34
has been set to Chrono 3, 6, 9 or 12. It should only be
adjusted after seeking advice from the manufacturer.
Press +until Option 35 is displayed, use Vor Λto
select required setting.
(NB Seek advice prior to adjusting)
2.5 = Integration time set to 2.5% (Factory Setting)
5 = Integration time set to 5%
10 = Integration time set to 10%
Option 36 - Set Temperature Override Rule
This establishes the degree of temperature override
available to the user. Press +until Option 36 is
displayed, use Vor Λto select required setting. This
option is not possible if the thermostat is set to STAT
in Option 40.
0 = No limit (Factory Setting)
1 = Limited to ±2ºC (±3ºF)
2 = No override allowed
Option 37 - Set Time Duration of Override Rule
This establishes the duration of a temperature
override available to the user. Press +until Option 37
is displayed, use Vor Λto select required setting. This
option is not possible if the thermostat is set to STAT
in Option 40 or Override Limit is disabled.
0 = Next Event (Factory Setting)
1 = 1 Hour
2 = 2 Hours
3 = 3 Hours
4 = 4 Hours