Danfoss TP9000 Guide

TP9000
Installation Instructions
User Instructions
Instrukcja montażowa
Instrukcja obsługi
Electronic Programmable
Room Thermostat plus
Domestic Hot Water Timer
GB
®
Certification Mark
PL

TP9000
2
Installation Instructions 3-14
Product Specification 3
Installation 4
Cable Access and Wiring 5
Installer Advanced Programming Options 8
User Instructions 15-31
What is a Programmable Room Thermostat 15
Preset programmes 17
Setting Date and Time 18
Changing Preset Programmes 20
User overrides 27
User Advanced Programming Options 33
Overview of Installer Selectable Features 37
Setting References 39
Index

GB
PL
DANFOSS HEATING 3
Please note: This product should only be installed by a qualified
electrician or competent Heating installer, and should be in
accordance with the current edition of the IEEE wiring regulations.
Specification 230V model 24V model
Power supply 230 Vac, ±15%,
50/60 Hz
24 Vac, ±15%,
50/60 Hz
Switching action
2 x SPDT internally linked, Type 1BS
Unit switch rating 230 Vac, 3(1)A 24Vac, 3(1)A
Memory Backup Retained for life of product
Heat Temperature Range
Setting
5°C - 30°C
Factory Set Calendar Clock Automatic Summer/Winter time
change
Remote Sensor Inputs
(‘A’ models only)
Can be set by installer for remote
sensor, limited sensor, window con-
tact, tele-switch or outdoor sensor
Programme resolution ± 1 minute
Timing Accuracy ± 1 minute
Dimensions, mm (W, H, D) 135 x 88 x 32
Design standard EN 60730-2-7 +EN60730-2-9
Control Pollution Situation Degree 2
Rated Impulse Voltage 2.5 kV
Ball Pressure Test 75°C
Product specification
Installation Instructions

TP9000
4
Installation
• Remove wallplate from unit by unscrewing the two screws on the
bottom edge of the unit.
• From the top left hand corner of the wallplate, there must be
clearances of at least 140 mm to the right, 15mm to the left, 30mm
above and 100mm below in order to mount the plug-on module.
• The wallplate must be securely mounted either directly to the
wall using suitable wood screws or to a flush mounted 1-gang
electrical accessory box using M3.5 screws.
• Cable access can either be from behind for concealed cabling, or
from below for surface cabling. If surface cable is used, cut out
cable access slot on plug-on module prior to mounting.
• For wiring connections refer to diagram on page 6.
The TP9000 is double insulated and does not require an earth
connection, however a parking terminal is provided on the
wallplate. This is clearly marked with an Earth symbol.
• Prior to mounting the plug-on module, DIL switches on the rear of
the plug-on module must be set. See diagram below for available
options.
• Mount plug-on module to wallplate by locating tabs on top of
wallplate in apertures on rear of module, hinge down and press
firmly to wallplate before tightening securing screws on bottom
of wallplate.
1
2
Keyboard disabled
Reset disabled Reset enabled
Keyboard enabled
OFF ON
Sw. No.
 Prior to mounting the unit the 2 DIL switches on the rear of the
unit have to be moved to the required position. The factory
presets are shown below.

GB
PL
DANFOSS HEATING 5
IMPORTANT: The supply to this unit should by wired via a double pole
isolationswitchinaccordancewithBSEN60730-1, i.e.onewhichprovides
air gaps of at least 3mm in both poles of the mains, and incorporates a 3
amp fuse. It is strongly recommended that solid conductors be used.
Clearance for
screwdriver
access
Surface fixed cable
bottom entry knockouts
Rear entry
cable access
N &
looping
terminals
Wall or
Plaster box
fitting
Terminal block
Outline of unit
30mm minimum
C/L
!
 Thermostat and Remote Room Sensor:
Fix at a height of approximately 1.5m from the floor, away from
draughts or heat sources such as radiators, open fires or direct
sunlight.

TP9000
6
Wiring
NOTE:
The TP9000 does not have voltage free contacts, therefore it is NOT
suitable for connection to extra low voltage equipment (i.e. > 50
Volts).
Remote Sensor to be wired with 1mm 2 core double insulated cable
only. Cable length should not exceed 50 metres. Sensor cable should
NOT be run parallel to mains cable.
Remote sensor inputs
The TP9000 incorporates an input which can be used to connect one
of the following:
1) remote room temperature sensor
2) limit sensor, for example, floor temperature sensor (sold as
accessory).
3) window contacts, card reader contacts, outdoor sensor (sold as
accessory) or teleswitch contacts.
See Installer Advanced Programming Options for set-up instructions.

GB
PL
DANFOSS HEATING 7
Remote sensor inputs
Terminals 5 and 6 are the designated remote sensor inputs. These can
be found on the top right hand side of the wallplate.
56
Window or
teleswitch
contact
(NO or NC)
56
Teleswitch
contact (NC)
Window
contact (NC)
56
Configured for
remote room,
limit or outdoor
sensor
Configured for
window contact or
other contact such
as teleswitch
Configured for
window contact
and other contact
such as teleswitch

TP9000
8
Installer advanced
programming options
TP9000 incorporates a number of advanced features which can be set
by the user. These are accessed via a User Advanced Programming
Mode, please refer to User Advanced Programming in the user
instructions for details (see page 33)
Installer advanced programming options
TP9000 incorporates an additional number of advanced features which
can be set by the installer to improve the operating efficiency of the
system and where required, to change the user functionality of the
product. These are accessed via an Installer Advanced Programming
Mode. These settings are optional and need only be made if there is a
demand for the enhanced functions.
Service Interval Timer
Instructions on how to access this feature are available from our
customer support desk. Please note these are only issued to boni-fide
Heating installers.
Entering Installer Advanced Programming Mode
To access the Installer Advanced Programming Mode follow the steps
below:
a) Press and hold Vand PROG for 3 seconds to
enter User Advanced Programming, the display
will change to figure opposite.
b) Press and hold V, Λand PROG for 5 seconds
to enter Installer Advanced Programming, the
display will change to figure opposite.

GB
PL
DANFOSS HEATING 9
c) Use +and -keys to scroll backwards and forwards between options
then Vand Λkeys to change the option settings. The flashing digit
on the right hand of the display indicates the number of the selected
option. The large characters display the option value selected.
d) To return to RUN, press and hold PROG until the display returns to
RUN mde.
Option 30 - Set upper limit of temperature range
This allows the upper limit of the thermostat setting
range to be electronically limited. Press +until
Option 30 is displayed, use Vand Λto select required
setting.
Setting 40 - 5°C (factory setting is 30°C)
Option 31 - Set lower limit of temperature range
This allows the lower limit of the thermostat setting
range to be electronically limited. Press +until
Option 31 is displayed, use Vand Λto select required
setting.
Setting 5 - 40°C (factory setting is 5°C)
Option 32 - Enable Off at lower limit
This enables an OFF function to be selected if a set
point below the lower limit is selected. Press +until
Option 32 is displayed, use Vand Λto select required
setting.
Setting 0 Disabled
Setting 1 Enabled (factory setting)
Option 33 - Enable On at upper limit
This enables an ON function to be selected if a set
point above the upper limit is selected. Press +until
Option 33 is displayed, use Vand Λto select required
setting.
Setting 0 Disabled (factory setting)
Setting 1 Enabled

TP9000
10
Option 34 - Select On/Off or Chrono-proportional
This allows the thermostat to be set to run in On/Off
mode or for a chrono-proportional cycle rate to be
selected. Press +until Option 34 is displayed, use V
and Λto select required setting.
0On/Off
33 cycles per hour
66 cycles per hour (factory setting)
99 cycles per hour
12 12 cycles per hour
Option 35 - Set integration time (Option 34 set to 3, 6, 9 or 12)
(seek advice prior to adjusting)
This adjusts the integration time of the PI algorithm
to increase control accuracy. It is only active if
option 34 has been set to Chrono 3, 6, 9 or 12.
It should only be adjusted after seeking advice
from the manufacturer. Press +until Option 35 is
displayed, use Vand Λto select required setting.
2.5 Integration time set to 2.5% (factory setting)
5Integration time set to 5%
10 Integration time set to 10%
Option 36 - Set temperature override rule
This establishes the degree of temperature override
available to the user. Press +until Option 36 is
displayed, use Vand Λto select required setting.
Setting 0 No limit (factory setting)
Setting 1 Limited to ±2°C
Setting 2 No override allowed