Danfoss TP5000 si range User manual

Fig.1
Space for additional
logo if required TP5000
User Instructions
Mon-Fri Sat-Sun
Event Time Temp°C Event Time Temp°C
1 06.30 20 1 07.00 20
2 08.30 15 2 16.00 21
3 11.30 20 3 23.00 15
4 13.30 15 4 00.00 15
5 16.30 21 5 01.00 15
6 22.30 15 6 01.59 15
Fig.2
i2 00
1
Before programming the thermostat press the + & – AND ∧∧
∧∧
∧and ∨∨
∨∨
∨ buttons
simultaneously to reset the unit (Fig.1)
Setting the Clock and Day
Press PROG (Fig.2) to begin programming
Use + or – buttons (Fig.3) to adjust the TIME (Fig.4)
Press PROG again (Fig.2)
Use + or – buttons (Fig.3) until correct DAY is shown (Fig.5)
(1 = Monday, 2 = Tuesday, etc)
Accepting the Factory Pre-settings
The TP5000 has pre-set times already programmed in, which often suit most
people (see Table below).
To accept these settings close the front cover and after 2 minutes the pre-
settings will automatically be accepted.
To adjust the factory pre-settings & set your own time and
temperature programmes
For Days 1-5 (weekdays)
a) Press PROG (Fig.2) 3 times to show the 1st pre-set time and temperature
(Event 1 Days 1,2,3,4,5) (Fig.6)
b) Use + or – buttons (Fig.3) to adjust the TIME (press and hold to change in
10 min increments)
c) Use ∧∧
∧∧
∧or ∨∨
∨∨
∨ buttons (Fig.7) to adjust the TEMPERATURE
d) Press PROG (Fig.2) to move to next preset time & temp (Event 2) (Fig.8)
e) Repeat steps b, c & d for programming Events 3, 4 5 & 6
For Days 6-7 (weekends)
●Press PROG (Fig.2) to show 1st pre-set time and temperature (Event 1
Days 6-7) (Fig.9)
●Repeat steps b, c and d above to programme time and temperature events
for the weekend
Returning to RUN mode
Press PROG (Fig.2) – the colon in the LCD display will start to flash (Fig.10)
Fig.6
Fig.7
Fig.5
Fig.3
Fig.4
Fig.8
20
1
i2 24
20
12345
1
6 30
20
67
1
7 00
15
12345
2
8 30
Fig.9
Fig.10

Danfoss Randall Ltd
Ampthill Road
Bedford, MK42 9ER
Tel: [phone]
Fax: [phone]
Email: [email protected]
Website: www.danfoss-randall.co.uk
Fig.14
Fig.16
Fig.12
Fig.13
Fig.11
Temporary User Overrides
The TP5000 has several useful overrides which can be selected without
affecting the thermostat programming
•Selection of time or actual room temperature in main LCD display –
press + and – together to change between settings (Fig.11)
•Temporary override of programmed temperature – press ∧∧
∧∧
∧or ∨∨
∨∨
∨ until
required temperature is displayed (override will automatically cancel at
beginning of next programmed event) (Fig.12)
•Temporary use of weekend programmes – press ∧∧
∧∧
∧and ∨∨
∨∨
∨ together
once (override cancels at 2:00am) (Fig.13)
•Frost Protection – a constant low temperature can be selected whilst
away from home - press ∧∧
∧∧
∧and ∨∨
∨∨
∨ together twice (Fig.14). To return to
automatic programming press ∧∧
∧∧
∧and ∨∨
∨∨
∨ together again
Summer Time / Winter Time Clock
●To change from Summer to Winter (clocks back) -
press and hold - button (Fig.15)
●To change from Winter to Summer (clocks forward) -
press and hold + button (Fig.15)
Battery Replacement
●A low battery symbol will flash in the LCD display (Fig.16)
●You have 15 days to replace the battery before the unit will switch off.
●When changing batteries, remove old batteries and insert new ones within
ONE MINUTE and programming will not be lost.
NB. If the display ever goes blank during normal operation, the batteries will
need to be renewed, the unit reset and the time and programmes reset.
Selection of time
or actual room
temperature
in main LCD
Temporary
override of
programmed
temperature
x 2
16
03 57
Temporary use
of weekend
programmes
Frost
Protection
Fig.15
Clocks
forward
Clocks
back