Danor LP-300 User manual

LP-300
18*12W LED PAR
WATERPROOF
USER MANUAL
Please read carefully before using the product

GENERAL INTRODUCTION
Please read and understand the instructions in this manual carefully and thoroughly
before attempting to operate this device. These instructions contain important safety and
use information.
This LP-300 shall be an IP-65 rated PAR color changer with (18) 12W 4-IN-1 RGBW LEDs.
shall operate flicker-free with an average LED life of 100,000 hours. And shall be capable of
emitting 3,950 Lux @ 3m. It shall include color and chase macros and have 25°beam and
45°field angles. The LP-300shall house an electronic strobe and be capable of 0-100%
dimming with variable dimming curve modes. The LP-300 shall operate via DMX and RDM
and include a 4- button control panel display. Exterior construction shall be of die-cast
aluminum and the LP-300 shall contain a dual yoke / floor stand. Max power consumption
shall be 220W and a multi-voltage universal auto switching power supply (110-250v) shall
be included. It shall measure 365mm x 157mm x 365mm (LxWxH) and weigh 8.1 kg.
Please note that although this fixture is IP rated, the fixture is not suitable for marine/or
coastal environment installations. Installing this fixture in a marine and/or coastal
environment may cause corrosion and/or excessive wear to the interior and/or exterior
components of the fixture. Damages and/or performance issues resulting from installation
in a marine and/ or coastal environment will void the manufacturers warranty and will not
be subject to any warranty claims and/or repairs.
UNPACKING
Every device has been thoroughly tested and has been shipped in perfect operating
condition.
Carefully check the shipping carton for damage that may have occurred during shipping. If
the carton is damaged, carefully inspect the device for damage, and be sure all accessories
necessary to install and operate the device have arrived intact. In the event damage has
been found or parts are missing, please contact our customer support team for further
instructions.

1. SECRUITY WARNING.
DO NOT PLUG FIXTURE INTO A DIMMER PACK! NEVER OPEN THIS FIXTURE
WHILE IN USE! UNPLUG POWER BEFORE SERVICING FIXTURE! NEVER TOUCH FIXTURE
DURING OPERATION, AS IT MAY BE HOT! KEEP FLAMMABLE MATERIALS AWAY FROM
FIXTURE!
NEVER LOOK DIRECTLY INTO THE LIGHT SOURCE! RETINA INJURY RISK - MAY
INDUCE BLINDNESS! SENSITIVE PERSONS MAY SUFFER AN EPILEPTIC SHOCK!
MINIMUM DISTANCE TO OBJECTS/SURFACES MUST BE 65.6 FEET (20
METERS) MAXIMUM TEMP OF EXTERNAL 90°C,MINIMUM DISTANCE OF INFLAMMABLE
MATERIALS FROM THE SURFACE 1.6 FEET (0.5 METER)
FIXTURE MUST BE PROPERLY GROUNDED.
2. CAUTIONS.
■Please keep this brochure as a reference for future consultation. If you sell this product
to other users, make sure they get the brochure as well.
■Before using the product, please open it and check carefully to see if the product is
damaged by transportation.
■Ensure that the supply voltage is in line with the equipment requirements before
operation
■Combustible materials should not be placed next to the equipment when it is running,
and there is a fire risk.
■Safe ropes should be used when hang on this equipment. The equipment should not
be carried by bare hands, but the bottom should be lifted at the same time.
■In case of serious operational failure, stop using the equipment immediately and do

not attempt to repair it alone. Non-professional maintenance alone can cause damage
and functional failure. Please contact the authorized Technical Assistant Center nearby.
■Do not touch the power supply during operation. High voltage may cause electric
shock hazard.
■Replacement is necessary when obvious damage occurs to the housing, lens or
ultraviolet filter.
■Disconnect the main power supply when replacing the spare parts
Lighting fixtures should be screwed onto the bracket to ensure that they are firmly installed
to prevent flutter and slip during operation and to ensure that the structure connecting the
lamps can support the lamps.
2. TECHNICAL PARAMETERS.
Input voltage: AC90-240V, 50/60Hz
Consumption power: maximum 180W
LED: 18X12W 4-IN-1 OR 5-IN-1 Muti-chips(RGBW，RGBA OR RGBWA)
Lenses Angle:25 degrees
Operation mode: DMX512 signal, voice control
DMX Channel: 8 Channel Mode
0-100% linear dimming function
Protection Level: IP65
Shell Material: Die Cast Aluminum Shell, Color: Black
Input mode: power input-output, signal input-output
National Standard Hand-in-Hand Wire, 1.5 Squares
Signal Plug: Standard Waterproof Signal Plug
Weight: 8.1kg，Product Dimension: 365*157*365mm
Packaging size: 530*530*350mm(MASTER CARTON 4 IN 1),
Single Packing:250*250*320mm
Installation: 110V, maximum series 4, 220V, maximum series 8, indoor and outdoor use as
far as possible grounding.

3. OVERVIEW
3.1 INSTALLATION GUIDELINES.
MOUNTING THE FIXTURE ON A TRUSS USING CLAMP
When mounting the fixture to a truss, be sure to secure an appropriately
rated professional grade rigging clamp (not included) to the closed dual
yokes using an M10 screw fitted through the center hole of the closed
dual yokes. The dual yokes of the fixture provides a rigging point
for a SAFETY CABLE (not included). Be sure to only use one of the
designated rigging points for the safety cable and never secure a safety
cable to a carrying handle.
3.2. SAFETY CABLE .

ALWAYS ATTACH AN APPROPRIATELY RATED SAFETY CABLE
WHENEVER INSTALLING THIS FIXTURE IN A SUSPENDED NVIRONMENT
TO ENSURE THE FIXTURE WILL NOT FALL IF THE CLAMP FAILS.
4. DISPLAY CONTROL.
MENU：FUNCTION UP：+ DOWN：- ENTER：CONFIRM

5. SYSTEM MENU.
：DMX standard 8CH mode( press UP/DOWN key to select the
DMX values 1-512, Press Enter key to save)
：DMX simple 4CH mode.
：Slave mode.
：Gradually change mode(press UP/DOWN to select speed at
1-50, press ENTER to save)
：Jump change mode( press UP/DOWN to select speed at 1-50,
press ENTER to save)
：Pulse change mode( press UP/DOWN to select speed at 1-50,
press ENTER to save)
：color change mode（Press ENTER TO select the colors）
Red，press UP/DOWN to increase/decrease the number of
DMX values within 0-255..
Green，press UP/DOWN to increase/decrease the
number of DMX values within 0-255.
Blue，press UP/DOWN to increase/decrease the
number of DMX values within 0-255..
White，press UP/DOWN to increase/decrease the
number of DMX values within 0-255..
：Strobe Mode, ( press UP/DOWN to select speed at 1-50, press
ENTER to save)

：Sound control mode.
：Master mode (Slavers set as d001)
6. DMX CHANNELS.
4 Channels mode(D001)
CH
Value
Function description
CH1
0-255
RED(0-100%)
CH2
0-255
GREEN(0-100%)
CH3
0-255
BLUE(0-100%)
CH4
0-255
AMBER (0-100%)
8 Channels mode(A001)
CH
Value
Function description
CH1
0-255
RED(0-100%)
CH2
0-255
GREEN(0-100%)
CH3
0-255
BLUE(0-100%)
CH4
0-255
AMBER (0-100%)
CH5
0-255
COLOR MACRO
CH6
0-255
COLOR MACRO SPEED
CH7
0-255
TOTAL DIMMER
CH8
0-255
STROBE (&Strobe effects)

7.TROUBLE SHOOTING.
7.1 MAINTENANCE GUIDELINES.
DISCONNECT POWER BEFORE PERFORMING ANY MAINTENANCE!
Frequent cleaning is recommended to insure proper function, optimized
light output, and an extended life. The frequency of cleaning depends on
the environment in which the fixture operates: damp, smoky or
particularly dirty environments can cause greater accumulation of
dirt on the fixture’s optics. Clean the external lens surface at least every
20 days with a soft cloth to avoid dirt/debris accumulation.
NEVER use alcohol, solvents, or ammonia-based cleaners.

Please refer to the following points during routine inspections:
•A detailed electric check by an approved electrical engineer every
three months, to make sure the circuit contacts are in good condition
and prevent overheating.
•Be sure all screws and fasteners are securely tightened at all times.
Lose screws may fall out during normal operation resulting in damage or
injury as larger parts could fall.
•Check for any deformations on the housing, color lenses, rigging
hardware and rigging points (ceiling, suspension, trussing).
•Electric power supply cables must not show any damage, material
fatigue or sediments.
•NEVER remove the ground prong from the power cable