DARCHE ECO Series User manual

DARCHE.COM.AU
INSTRUCTION MANUAL
T050801209ECO
ECO DIRTY DEE

2
INSTRUCTION MANUAL
CONTENTS
• 1 x Eco Dirty Dee swag
• 1 x Composite swag pole pack (9 sections that make up 3 poles)
• 2 x Trigger lock spreader pole
• 1 x 70mm high-density foam mattress
• 1 x Carry bag
• 8 x Pegs
• 4 x Guy ropes

DARCHE.COM.AU
PLEASE NOTE
Prior to first use of the Dirty Dee swag, it is important to remove the mattress from its compression sleeve and allow
it to expand.
Step 1
Unroll the swag onto a flat, well-drained area free of sharp objects that may penetrate the swags PVC floor.
Eachcomposite pole will be dierent in length and all correspond to a specific placement on the swag. Refer to the
labelling on the poles.
Remove the HEAD pole bundle (3x pole sections) from
the pack:
• 2x END section poles (aluminium sleeve on one
endof the pole).
• 1 x MIDDLE section pole (angled aluminium sleeves
on both ends of the pole)
Step 3
Assemble one END section pole into the MIDDLE section angled pole sleeve.
Step 2
Feed the angled middle pole through the sleeve on top of the swag and centre the pole within the swag sleeve.

4
INSTRUCTION MANUAL
Step 5
Insert the second END pole to the other end of the MIDDLE section angled pole sleeve. Place your palm under the
pole end, and push upward until there is a gap between the pole end and the second pin. Insert the second pin.
DUSK TO DAWN
Step 6
Repeat this process for the other CENTRE and FOOT poles.
Step 4.
The end of the pole will have the aluminium sleeve to insert the base pin. Insert the first pole end onto the base pin.

DARCHE.COM.AU
Step 7
Clip the swag to the composite poles one end at a time. A good technique for attaching the clips is to alternate from
one side to the other. Top left then top right, second left and then second right and so on.
12
34
56
At this point you should have all three composite poles assembled, located in their corresponding positions and
have centralised the swag at each point. The clips should all be attached to the composite poles on each side.
Stretch out the floor of the swag to ease assembly when placing the trigger lock spreader poles.
DIRTY DEE
HEAD
CENTRE FOOT

6
INSTRUCTION MANUAL
Step 5
Insert the trigger lock spreader pole into one of the centre eyelets. Release the trigger to extend the pole and insert
into one of the end eyelets. Tension the bar to stretch the swag into shape then lock into position. Repeat this
process for the other spreader pole. The guy ropes and pegs can be used if required.
Now your Dirty Dee swag set up is complete.
PACK DOWN
1. Partially close all the zips, door covers and window flaps, leaving them slightly open will allow for the air to
escape while rolling up. Remove pegs and guy ropes if used.
2. Release the trigger of the spreader poles and remove them from the eyelets.
3. Unclip the swag from the composite poles one at a time.
4. Disassemble all of the poles in preparation for step 5 below. Tip: Leave the MIDDLE poles in each sleeve to
make things easier for your next trip. Stow the END pole sections in the sleeve along with the MIDDLE pole.
5. While the swag is laid out flat, bring any overhanging material and ropes into the centre of the swag. Beginning
from the head end, start rolling the swag as tightly as possible in an attempt to expel as much air as possible
to achieve a compact roll. Tip: Using your knees, or two people while rolling, will assist in getting the swag as
compact as possible. Just before completing the rolling process, place the retracted spreader pole between the
fabric and continue the rolling process to the end.
6. Bring the two compression straps together and loop through the double D-rings, do not over tighten the straps.

DARCHE.COM.AU
NOTE
Allow a wet or damp swag and all bedding inside, to dry thoroughly before pack down. If this is not possible,
unroll swag as soon as possible. Allow to fully dry out before re-packing and storing.
SPARE PARTS LIST
For a full list of Spare Parts available refer to DARCHE.COM.AU
CARE & STORAGE INSTRUCTIONS
1. Remove dirt with a soft brush and cold water after use.
2. Do not clean with soap, detergent, petrol, oil or solvents.
3. Ensure swag is completely dry before storing.
4. Do not store directly on concrete floors. A dry shelf in your shed or a cupboard is a perfect spot for your
swag when not in use.
5. If spot mould is visible, brush it o with a sti bristle nylon brush and vacuum the area to get rid of any
residual spores.
6. Leaving your swag rolled too tightly for long periods of time may result in the mattress taking a while to bounce
back. If it’s been a while since your last adventure, open your swag a few days before you leave and allow the
mattress to expand. Re-pack your swag and have a great weekend.
MOISTURE/CONDENSATION
Condensation is a natural occurrence in confined areas like swags/tents due to the body releasing more moisture
than the canvas can dispose of in cold weather. To minimise the chance of condensation, we recommend slightly
opening a window to enable airflow on cold nights.

INSTRUCTION MANUAL
Designed and tested in Australia for Australian conditions.
A brand by Charles Parsons.
Telephone [phone] l Email: [email protected]
75 Heyington Avenue, Thomastown VIC 3074, Australia.
DARCHE: LEADERS IN OUTDOOR DESIGN. PROUDLY AUSTRALIAN.
Due to our policy of continual product development,
the specifications, colours and features may vary.
DARCHE.COM.AU
V1- August 2022