Dat Optic T1-US2DS01 User manual

1. Lock Screw
2. 3.5” SATA Mobile Tray
2-1. Drive 1
2-2. Drive 2
3. Device LED
3-1. Drive 1
3-2. Drive 2
4. Power LED (Green)
5. Alarm LED (Red)
6. AC Input
AC 100~240V, 47~63Hz, 72W
7. Power On/OFF
8. Cooling Fan
9. eSATA Connector
10. Host Status LEDs
11. Change Mode Button
12. Rotary switch
13. USB Host LED
14. USB B Type Connector
15. Alarm LED
16. Power LED
2
.
Installation Guide
T1-US2DS01
Overview
Introduction
69 10
11 12
13 14
15
16
7
8
1
2-1
3-1
4 5 2-2
3-2
Alarm LED: ( Red LED)
Volume degradation (RAID 1) or unavailability
(JBOD, Big, Fast) will be marked by turning on the
Alarm LED and the alarm Buzzer for the node that
experienced this behavior.
Power LED: ( Green LED)
LEDs on JBOD Mode
Description
Device Unplugged/No power
Device Plugged (Idle)
Device Plugged (Activity)
LEDs on RAID Mode
Description
Device Unplugged/No power
Device Plugged (Idle)
Device Plugged (Activity)
Disk Rebuild
(A Physical Partition is being
Rebuilt;Safe Mode(RAID 1))
Disk Rebuild-Verify
(A Physical Partition is being
Verified; Safe Mode (RAID1))
Green(Link)
Off
On
On
Link
Blink
On
On
Blink
On
Red(ACT)
Off
Off
Flash (On)
ACT
Blink
Off
Flash (On)
On
Flash (On)
will appear as On
Device LED (ACT & Link) :
Normal
LED
RAID 1 Status Error
ON
OFF
You can configure the T1-US2DS01 to use the following Storage
Policies to map its appliance's physical hard drives to virtual drives
that are visible to the host computer.
- BIG (Concatenation)
- JBOD (Just a Bunch Of Disks)
- FAST (RAID 0)
- SAFE (RAID 1)
- SAFE33 (1/3 to SAFE mode and 2/3 to BIG mode)
- SAFE50 (1/2 to SAFE mode and 1/2 to BIG mode)
- GUI (Use the SteelVine Manager GUI to configure the Storage Policy)
Rotary switch:
To select a storage policy in this mode the first time that
a new factory-shipped product is used, ensure that the
hard disk drives are installed, set the rotary switch on
the back of the T1-US2DS01 to the desired Storage
Policy (not the GUI selection) and turn on the power.
Change Mode Button:
To change the storage policy thereafter, set the rotary
switch to the desired position and press the recessed
Change Mode Button to create the new virtual
volume(s). Creating new virtual volumes will destroy
any existing data that existed on the previous volume,
but expanding an existing BIG volume will not destroy
any existing data.
LEDs
Front Panel Back Panel
Rotary switch & Change Mode Button
DISK 1 DISK 2
Activity
(Red)
Link
(Green)
Activity
(Red)
Link
(Green)
T1-US2DS01 is an eSATA & USB 2.0 Combo to Dual SATA RAID storage enclosure.
It provides two hot-swappable 3.5" HDD mobile trays for easy installation and un-installation.
T1-US2DS01 is a hardware RAID enclosure, requiring no software installation on the user’s machine.
The user can select different RAID modes for the two 3.5" SATA HDDs.
You can configure the T1-US2DS01 to use the following Storage Policies to map its appliance's physical hard drives to virtual drives that are visible to
the host computer.
* BIG (Concatenation)
* JBOD (Just a Bunch Of Disks)
* FAST (RAID 0)
* SAFE (RAID 1)
* SAFE33 (1/3 to SAFE mode and 2/3 to BIG mode)
* SAFE50 (1/2 to SAFE mode and 1/2 to BIG mode)
* GUI (Use the SteelVine Manager GUI to configure the Storage Policy)
QL.NB278.12

Installation Guide
T1-US2DS01
Installing Hard Disk Drive
Applications
1. For desktop use
T1 can stand up vertically with foot stands.
1. Unscrew the Lock screw on the Mobile Tray. 6. Replace the Lock screw on the Mobile Tray.
7. Attach the Power Cable
2. To remove the Mobile Tray, hold the mobile tray firmly and
gently pull out the tray from the housing.
3. To install a SATA HDD, simply place the HDD inside the tray
as illustrated below. (A stopper in the rear of the tray is provided
to ensure proper alignment)
4. After placing the HDD inside the tray, secure the HDD with four
screws
5. To insert the tray, hold the mobile tray firmly and push it back into
the housing.
2. For rack mount
Two T1 can be linked together with four fixed brackets.
Stick 4 Rubbers
on foot stand
QL.NB272.12
Note: Input : AC 100~240V, 47~63Hz