Data I/O Sprint PLUS 48 User manual

4 1
983-0126-003
Data I/O has attempted to ensure that the information in this document is accurate and complete. Data I/O assumes no liability for errors, or for any incidental,
consequential, indirect, or special damages, including, without limitation, loss of use, loss or alteration of data, delays, or lost profits or savings, arising from the
use of this document or the product which it accompanies.
No part of this document may be reproduced or transmitted in any form or by any means, electronic or mechanical, for any purpose, without written permission
from Data I/O.
Acknowledgments:
Data I/O is a registered trademark of Data I/O Corporation.
Data I/O Corporation acknowledges the trademarks of other organizations
for their respective products or services mentioned in this document.
©1999/2003 Data I/O Corporation
All rights reserved
Sales and Technical Support
Contact your local Data I/O representative or see the contacts below. To find your
local representative on our Web site go to http://www.dataio.com/RepSearch.asp
Worldwide except Canada and Europe
Data I/O Corporation
Shipping address:
10525 Willows Road N.E.
Redmond, WA USA 98052
Mailing address:
P.O. Box 97046
Redmond, WA USA 98073-9746
Telephone: [phone]; Outside US: 425-867-6870
Fax: [phone]
E-mail: [email protected]
Canada
Data I/O Canada
6725 Airport Road, Suite 102
Mississauga, Ontario, Canada L4V 1V2
Telephone: [phone]
Fax: [phone]
E-mail: [email protected]
Europe
Data I/O GmbH
Lochhamer Schlag 5
82166 Gräfelfing, Germany
Telephone: [phone]
Fax: [phone]
E-mail: ccs-europ[email protected]
When calling or writing, please provide the following information:
• Serial number
•Interface—”TaskLink for Windows” or “Sprint Windows”
• Software Version
• Detailed description of the problem you are experiencing
• Error messages (if any)
• Device manufacturer, part number, package style and number of pins (if device-
related)
• Name, telephone number and address
On the World Wide Web, contact us at http://www.dataio.com
or at our German Web site at http://www.dataio.de
Sprint PLUS 48
Getting Started Guide
The PLUS 48®is a desktop IC
Programmer that can accommodate
DIP devices.
The serial number is located on the
bottom of the unit.
• Parts included with the PLUS 48
• Assembly Instructions
• Installing a Device
• System Requirements
• Operating Requirements
• Technical Specifications
• Sales and Technical Support
on your Sprint family programmer or
using the software, refer to
documentation on the “TaskLink™for
Windows®” CD.
Congratulations on purchasing
your new Sprint PLUS 48
This guide describes: For more information...

2 3
figure 1: Rear View
In this package you will find:
• TaskLink CD-ROM (software and User Manual)
• PLUS 48 unit
• 25 pin, 1:1 parallel cable, 32” long
• Power Cord
• PLUS 48 Power supply
• Calibration tool
Assembly Instructions
Before beginning, ensure that the power is turned off at both the programmer
and your computer.
1. Connect one end of the parallel cable to the port on the back of the pro-
grammer.
2. Connect the other end of the cable to the parallel port of your computer.
Any empty parallel port on your computer may be used.
3. Install the power supply by inserting the small DIN jack of the power supply
into the power socket on the back of the programmer. This jack is keyed
and cannot be inserted incorrectly.
4. Connect power cord between the power supply box and a 100-250 Volt,
50-60 Hz AC outlet.
WARNING: A device may be damaged if it is in the socket during
power up. Remove all devices before turning the
power switch on.
WARNING: Electrostatic Discharge (ESD) may damage inte-
grated circuits (devices). A grounding strap should
be worn at all times while programming devices.
You are now ready to install the TaskLink for Windows software and begin pro-
gramming devices. Refer to the TaskLink for Windows CD.To install the soft-
ware see the jewel case front tray liner.
PLUS 48 Power Supply
Parallel Cable
Calibration Tool
TaskLink CD
Static ground
connection Power switch
DIN connection
Parallel Port
Installing a Device
With the socket unlocked (lever in the up position), insert the device with the
notch away from you. The socket is bottom justified. Lock the socket. See fig-
ure 2.
System Requirements
• Microsoft Windows 95, Windows 98 or Windows NT
• 75MB free hard disk space
•CD-ROMdrive
• Bus or Serial Mouse
• Parallel port
Operating Requirements
• Operating voltage: 100-240 V~±10%
• Frequency range: 50-60 Hz
• Power consumption: 12 Watts
Technical specifications
• 48-pin DIP socket (300/600mil lead spacing)
• Universal analog and digital pin drivers
figure 2: Installing a Device