Data Video ITC-100SL User manual

www.datavideo.com
ITC-100SL
INTERCOM BELT PACK
Instruction Manual

2
Table of Contents
FCC COMPLIANCE STATEMENT....................................3
WARNINGS AND PRECAUTIONS ...................................3
WARRANTY........................................................................5
STANDARD WARRANTY ............................................................... 5
THREE YEAR WARRANTY ............................................................. 5
DISPOSAL...........................................................................6
ITC-100SL SLAVE UNIT....................................................7
SPECIFICATION...............................................................10
SERVICE AND SUPPORT...............................................11
Disclaimer of Product & Services
The information offered in this instruction manual is intended as a guide only. At all
times, Datavideo Technologies will try to give correct, complete and suitable
information. However, Datavideo Technologies cannot exclude that some
information in this manual, from time to time, may not be correct or may be
incomplete. This manual may contain typing errors, omissions or incorrect
information. Datavideo Technologies always recommend that you double check
the information in this document for accuracy before making any purchase
decision or using the product. Datavideo Technologies is not responsible for any
omissions or errors, or for any subsequent loss or damage caused by using the
information contained within this manual. Further advice on the content of this
manual or on the product can be obtained by contacting your local Datavideo
Office or dealer.

3
FCC Compliance Statement
This device complies with part 15 of the FCC rules. Operation is subject
to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including
interference that may cause undesired operation.
Warnings and Precautions
1. Read all of these warnings and save them for later
reference.
2. Follow all warnings and instructions marked on this
unit.
3. Unplug this unit from the wall outlet before cleaning. Do not use
liquid or aerosol cleaners. Use a damp cloth for cleaning.
4. Do not use this unit in or near water.
5. Do not place this unit on an unstable cart, stand, or table. The unit
may fall, causing serious damage.
6. Slots and openings on the cabinet top, back, and bottom are
provided for ventilation. To ensure safe and reliable operation of
this unit, and to protect it from overheating, do not block or cover
these openings. Do not place this unit on a bed, sofa, rug, or
similar surface, as the ventilation openings on the bottom of the
cabinet will be blocked. This unit should never be placed near or
over a heat register or radiator. This unit should not be placed in a
built-in installation unless proper ventilation is provided.
7. This product should only be operated from the type of power
source indicated on the marking label of the AC adapter. If you are
not sure of the type of power available, consult your Datavideo
dealer or your local power company.
8. Do not allow anything to rest on the power cord. Do not locate this
unit where the power cord will be walked on, rolled over, or
otherwise stressed.

4
9. If an extension cord must be used with this unit, make sure that the
total of the ampere ratings on the products plugged into the
extension cord do not exceed the extension cord rating.
10. Make sure that the total amperes of all the units that are plugged
into a single wall outlet do not exceed 15 amperes.
11. Never push objects of any kind into this unit through the cabinet
ventilation slots, as they may touch dangerous voltage points or
short out parts that could result in risk of fire or electric shock.
Never spill liquid of any kind onto or into this unit.
12. Except as specifically explained elsewhere in this manual, do not
attempt to service this product yourself. Opening or removing
covers that are marked “Do Not Remove” may expose you to
dangerous voltage points or other risks, and will void your
warranty. Refer all service issues to qualified service personnel.
13. Unplug this product from the wall outlet and refer to qualified
service personnel under the following conditions:
a. When the power cord is damaged or frayed;
b. When liquid has spilled into the unit;
c. When the product has been exposed to rain or water;
d. When the product does not operate normally under
normal operating conditions. Adjust only those controls
that are covered by the operating instructions in this
manual; improper
e. adjustment of other controls may result in damage to the
unit and may often require extensive work by a qualified
technician to restore the unit to normal operation;
f. When the product has been dropped or the cabinet has
been damaged;
g. When the product exhibits a distinct change in
performance, indicating a need for service.

5
Warranty
Standard Warranty
Datavideo equipment are guaranteed against any manufacturing
defects for one year from the date of purchase.
The original purchase invoice or other documentary evidence should
be supplied at the time of any request for repair under warranty.
The product warranty period beings on the purchase date. If the
purchase date is unknown, the product warranty period begins on the
thirtieth day after shipment from a Datavideo office.
Damage caused by accident, misuse, unauthorized repairs, sand, grit
or water is not covered under warranty.
Viruses and malware infections on the computer systems are not
covered under warranty.
Any errors that are caused by unauthorized third-party software
installations, which are not required by our computer systems, are
not covered under warranty.
All mail or transportation costs including insurance are at the
expense of the owner.
All other claims of any nature are not covered.
Cables and batteries are not covered under warranty.
Warranty only valid in the country or region of purchase.
Your statutory rights are not affected.
Three Year Warranty
All Datavideo products purchased after July
1st, 2017 are qualified for a free two years
extension to the standard warranty,
providing the product is registered with
Datavideo within 30 days of purchase.
Certain parts with limited lifetime
expectancy such as LCD panels, DVD drives, Hard Drive, Solid State
Drive, SD Card, USB Thumb Drive, Lighting, Camera module, PCIe
Card are covered for 1 year.
The three-year warranty must be registered on Datavideo's official
website or with your local Datavideo office or one of its authorized
distributors within 30 days of purchase.

6
Disposal
For EU Customers only - WEEE Marking
This symbol on the product or on its packaging
indicates that this product must not be disposed of
with your other household waste. Instead, it is your
responsibility to dispose of your waste equipment by
handing it over to a designated collection point for
the recycling of waste electrical and electronic
equipment. The separate collection and recycling of
your waste equipment at the time of disposal will
help to conserve natural resources and ensure that it is recycled in a
manner that protects human health and the environment. For more
information about where you can drop off your waste equipment for
recycling, please contact your local city office, your household waste
disposal service or the shop where you purchased the product.
CE Marking is the symbol as shown on the left of
this page. The letters "CE" are the abbreviation of
French phrase "Conformité Européene" which
literally means "European Conformity". The term
initially used was "EC Mark" and it was officially
replaced by "CE Marking" in the Directive
93/68/EEC in 1993. "CE Marking" is now used in all EU official
documents.

7
ITC-100SL Slave Unit
XLR Connection
Connects the ITC-100SL to the ITC-100 Base Station.
Power, tally and bi-directional audio are all carried
through the same cable.
Call Button
Sends a paging message to the ITC-100 Base Station.
The channel button will flash orange and there will be an
audible tone, each time the button is pressed.
Bi-Color Tally LED
RED indicates LIVE
Green indicates
CUED

8
Bi-Color Tally LED
Will illuminate RED when the channel is LIVE
Green color means the channel is CUED
Talk Button
Opens up talk back communication with the ITC-100
base station, and any other active channels. Press to
activate; release to de-activate. PLEASE NOTE: It is
important to deactivate the talk channel as soon as
you have finished talking, otherwise it will remain an
open channel and become distracting and confusing
for other members of the crew.
Volume Control
Adjusts the volume of the headphones.
Mic / Headphone Socket
The ITC-100SL has both a 3.5mm and 2.5mm Mic /
Headset socket. A standard 3.5mm Mic / Headset can be
used, or a Motorola type 2.5mm Mic / headset could be
used if preferred.

9
External Tally LED Socket
An external tally display (TD-2) can be connected to the
ITC-100SL. This enables the tally light to be positioned in
a more convenient place, such as on top of the camera.
When the channel is LIVE the LED will be RED, and
when the channel is CUED the LED will be AMBER.
N.B. The Tally LED on the ITC-100SL will continue to
operate as normal when a TD-2 has been added.
Power LED
The Power LED indicates when the channel is active. If
the operator has opened the channel by pressing the
channel button 1 ~ 8, or by pressing ALL then the LED
will light up.
N.B. The tally indicator lights will continue to work
even when the Power LED is not on, and the channel
is not active.

10
Specification
INPUT
5 Pin XLR Connector
MIC /
HEADSET
SOCKET
3.5mm Stereo Jack Socket for combination
Headphone / Microphone
Headset Impedance 8~600 ohms 100mW(min)
Microphone Level -67dB
Or
2.5mm Stereo Jack Socket, for Motorola Mobile
Phone type headset / microphone
FREQUENCY
RESPONSE
550-3.6KHz, < +/-3dB
THD
< 3%
S/N
50dB
TALLY OUT
SOCKET
3.5mm Jack Socket to connect to TD-2 or TD-3
Tally Indicator
TALLY LED
Bi-Color LED – RED indicates LIVE / GREEN
Indicates CUED
POWER LED
Illuminates to indicate that power is being
received
OPERATING
RANGE
Up to 200m between Base Station and Slave
OPERATING
TEMP. RANGE
5 ~ 45°C
DIMENSION
114mm x 97mm x 35mm
WEIGHT
348g