Data Video SE-800 Quick start guide

SE-800AV to DV
Upgrade Instructions
http://www.datavideo-tek.com

Parts needed to upgrade the SE-800AV to SE-800:
Item Description Part number Num
1SDI OUT Module 305-SDI-OUT 1
2DV OUT Module 305-DV-OUT 1
3DV IN Module B361N0-305 4
4IDE FLAT CABLE 26P(female)-26P(female) 50mm UL 07640260004 4
5SDI board rear metal plate 09310003052 1
6DV in board rear metal plate 09310003053 4
7Screws f3 * 12mmblack 09111301201 2
8Screw ISO w/spring and washer 3 * 8mm 09112300813 20
9 Hex risers 17mm 09160000171 4
10 Hex risers 20mm 09160000201 16
11 Nut f3 * 5.5mm for hex risers 09140301003 20

Step1: Open the SE-800 top cover
There are another 7 screws on the bottom case to be removed and then you can lift off
the top cover.
Step2:
There is a screw inside this hole, that
needs to be removed.
Remove all 4 screws holding
the metal braces

Step3:
Step4:
Remove two metal braces, four AV IN Modules and one NO-SDI card
Remove 10 rear panel screws
NO SDI Card x 1 AV IN Module Card x 4

Step5:
SDI Out Module Card
Description Part number
SDI OUT Module 305-SDI-OUT
DV Out Module Card
Description Part number
DV OUT Module 305-DV-OUT
Add four hex risers (17mm) onto the SDI Out Module Card with 4 (5.5mm) Nuts
Description Part number
17mm hex risers
09160000171
f3 * 5.5mm Nut
09140301003
SDI Out Module Card

Step6: Put DV Out Module Card onto SDI Out Module Card with 4 ISO 3 * 8mm
screws with the spring and washer.
Add on the SDI rear panel with two f 3 * 12mm screws
Step7: Add four hex risers (20mm) on the AV IN Module Card and fasten with Nuts
Description Part number
SDI board rear metal plate 09310003052
Screws f 3 * 12mm black 09111301201
Screws ISO 3 * 8mm with spring and washer 09112300813
AV IN Module Card
Description Part number
hex risers 20mm
09160000201
Nut f 3 * 5.5mm
09140301003

Step8: Connect the IDE FLAT CABLE on to J2 of the DV IN Module Card
(Please note: the red line on cable should match Pin 1 of J2)
Step 9: Adjust the NTSC/PAL J4 Jumper setting on DV IN Module Card
Short on 1&2 for NTSC System
Short on 2&3 for PAL System
DV IN Module Card
Description Part number
DV IN Module B361N0-305
IDE FLAT CABLE 26P 50mm UL 07640260004

Step 10: Replace the original AV IN Module Card plate with the DV module plate.
Step 11: Add four ISO 3 * 8mm screws onto the DV IN Module Card
Connect the 26-Pin FLAT CABLE from the DV to AV card
DV module rear Plate
Description Part number
DV module rear plate (6-Pin DV) 09310003053
AV IN and DV IN Module Card
Description Part number
Screw ISO 3 * 8mm with spring and washer 09112300813

Step12: Follow Step 7 to Step 11 to assemble the three remaining DV and AV
modules. Install all the modules with SDI/DV Out Module back onto the SE-800
PCI slot. (Shown below)
Step13:
Attach the metal braces to
secure the modules.

Note: The direction of the
metal brace assembly.
Note: The direction of metal
brace assembly.
Fasten all four screws
(two per side)