Data Video TLM-700HD User manual

7" TFT LCD Monitor
TLM-700HD
Quick Start Guide
www.datavideo-tek.com

1
Table of Contents
Warnings and Precautions.........................................................2
What's in the Box.......................................................................4
Introduction................................................................................4
Features ....................................................................................4
Connections & Control...............................................................5
Front Panel ................................................................................5
Rear Panel.................................................................................7
Menu Options ............................................................................8
Support Format........................................................................ 11
Specification ............................................................................12
Service & Support....................................................................13

2
Warnings and Precautions
1. Read all of these warnings and save them for later reference.
2. Follow all warnings and instructions marked on this unit.
3. Unplug this unit from the wall outlet before cleaning. Do not use
liquid or aerosol cleaners. Use a damp cloth for cleaning.
4. Do not use this unit in or near water.
5. Do not place this unit on an unstable cart, stand, or table. The unit
may fall, causing serious damage.
6. Slots and openings on the cabinet top, back, and bottom are
provided for ventilation. To ensure safe and reliable operation of this
unit, and to protect it from overheating, do not block or cover these
openings. Do not place this unit on a bed, sofa, rug, or similar
surface, as the ventilation openings on the bottom of the cabinet will
be blocked. This unit should never be placed near or over a heat
register or radiator. This unit should not be placed in a built-in
installation unless proper ventilation is provided.
7. This product should only be operated from the type of power source
indicated on the marking label of the AC adapter. If you are not sure
of the type of power available, consult your Datavideo dealer or your
local power company.
8. Do not allow anything to rest on the power cord. Do not locate this
unit where the power cord will be walked on, rolled over, or
otherwise stressed.
9. If an extension cord must be used with this unit, make sure that the
total of the ampere ratings on the products plugged into the
extension cord do not exceed the extension cord’s rating.

3
10. Make sure that the total amperes of all the units that are plugged
into a single wall outlet do not exceed 15 amperes.
11. Never push objects of any kind into this unit through the cabinet
ventilation slots, as they may touch dangerous voltage points or
short out parts that could result in risk of fire or electric shock. Never
spill liquid of any kind onto or into this unit.
12. Except as specifically explained elsewhere in this manual, do not
attempt to service this product yourself. Opening or removing covers
that are marked “Do Not Remove” may expose you to dangerous
voltage points or other risks, and will void your warranty. Refer all
service issues to qualified service personnel.
13. Unplug this product from the wall outlet and refer to qualified service
personnel under the following conditions:
a. When the power cord is damaged or frayed;
b. When liquid has spilled into the unit;
c. When the product has been exposed to rain or water;
d. When the product does not operate normally under normal
operating conditions. Adjust only those controls that are
covered by the operating instructions in this manual; improper
adjustment of other controls may result in damage to the unit
and may often require extensive work by a qualified technician
to restore the unit to normal operation;
e. When the product has been dropped or the cabinet has been
damaged;
f. When the product exhibits a distinct change in performance,
indicating a need for service.

4
What’s in the box?
Items Description Q’ty
1 TLM-700HD 1
2 Sunshield 1
3 Switching Adaptor DC 12V/1.5A 1
4 User’s Manual 1
Introduction
The Datavideo TLM-700HD is designed for outdoor field side for user; it
can be dust-proof, drop-proof, sunshade and carry easy, TLM-700HD is a
standard V-Mount enabling you to power the monitor using a universal
battery from a range of manufacturers, prefect for use in the field.
Features
z7” 16:9 Wide Screen Panel
zResolution: RGB 800X480 dots
zBrightness, Contrast, Colour, Tint Adjustable (Tint NTSC only)
zNTSC/PAL Auto Switching
z16:9 / 4:3 / 15:9 switchable
zCarry Case Included
zOSD Menu Control
zSupport Blue Only
zSupport Embedded Audio & Time Code
zBuilt in V-Mount kit

5
Connections & Control
Front Panel
Power Switch
Switches the power On / Off.
Stereo mini jack plug
For stereo headphones. The headphone volume is
controlled by the Audio Level Adjustments.
N.B. Audio source from HDMI or SDI audio embedded
audio.
Audio Level Adjustments
Allow you to adjust the headphones volume.
Source Button
Select Input source between SDI, YPbPr, CVBS, and HDMI.
Aspect Ratio Button
Sets the LCD aspect ratio to 15:9, 16:9 or 4:3
PATTERN
The PATTERN button can be generated a colour bar on
screen. Press the PATTERN button again to return normally
output.

6
BLUE
The BLUE button is set blue only enable, Press this button
to eliminate the red and green component of input signals.
Only the blue component of an input is displayed on the
screen. This facilitates adjustments of chroma and phase.
(Phase adjustment is effective only for NTSC signals).
MENU
Calls up the on-screen adjustment menu (See Menu
Options for more details).
UP / DOWN
Navigate the on-screen menu and set the functions & levels.
ENTER
Confirms the new settings or return to the default state.

7
Rear Panel
HD/SD - SDI input
BNC connector for SDI Input.
YUV input
BNC connectors for analog (Component) video inputs.
Composite video input
BNC connectors for analog (Composite) video inputs.
HDMI in interface
HDMI digital signal input connecter.
Support HDMI 1.1
Tally In
Send in red and yellow colour tally signal to tally LED. Red
means on-air, yellow means standby.
DC in socket
Connect the supplied 12V 1.5A PSU to this socket. The
connection can be secured by screwing the outer fastening
ring of the DC In plug to the socket.

8
Menu Options
1. Picture
- Press the MENU button into the system Picture setting mode.
- Press ENTER button into the Picture setting position.
- Press UP / DOWN button moving to the Brightness setting.
- Press ENTER button into the Brightness setting position.
- Press UP /DOWN button to setting the Brightness values from 0~100
- Press MENU button return to the Picture setting menu.
- Press SOURCE button exit the setting mode.
N.B. To select a different setting (Contrast, Saturation, Tint) use the UP /
DOWN buttons. Follow the same procedure to set the others values.
N.B. Brightness, Contrast and Saturation these three modes, the value all
the same as 0~100.
2. Audio
- Press the MENU button two times into the Audio setting mode.
- Press ENTER button into the Audio setting position.
- Press ENTER button to setting the audio volume indicator ON/OFF display on
the screen.
- Press SOURCE button exit the setting mode.
3. Func.
- Press the MENU button three times into the Func. setting mode.
- Press ENTER button into the Func. setting position.
- Press UP / DOWN button moving to the Center Mark setting.
- Press ENTER button to setting the center mark ON/OFF on the screen.
- Press UP / DOWN button moving to the Safety Zone setting.
- Press ENTER button to setting Safety Zone range (80, 90 or OFF).
- Press UP / DOWN button exit the setting mode.
N.B.To select a different setting (4:3 Screen, Cinema Zone) use the UP /
DOWN buttons. Follow the same procedure to set the others status.

9
4. Setup
- Press the MENU button four times into the Setup setting mode.
- Press ENTER button into the Setup setting position.
- Press UP / DOWN button moving to the OSD Timer setting.
- Press ENTER button into the OSD Timer setting position.
- Press UP / DOWN button to select the OSD display on screen time (value from
5~60 SEC).
- Press ENTER button to setting the OSD display on screen time.
- Press UP / DOWN button moving to the OSD Blending setting.
- Press ENTER button into the OSD Blending setting position.
- Press UP / DOWN button to select the OSD blending display on screen (value
from 0~7).
- Press ENTER button to setting the OSD blending display on screen
- Press UP / DOWN button moving to the Timer Code setting.
- Press ENTER button to setting the Time Code ON/OFF on the screen.
- Press UP / DOWN button moving to the TC Position setting.
- Press ENTER button to setting the Time Code Position on the screen (Left/Up,
Middle/Down, Right/Down, Right/Up)
- Press UP / DOWN button moving to the TC HD Line setting.
- Press ENTER button to setting the time code for HD line (8~20).
- Press UP / DOWN button moving to the TC SD Line setting.
- Press ENTER button to setting the time code for SD line (10~21).
- Press UP / DOWN button moving to the TC Font Size setting.
- Press ENTER button to setting the time code font size on the screen (Large or
Small).
- Press MENU button return to the Setup setting menu.
- Press SOURCE button exit the setting mode.