Datalogic Magellan 2200VS User manual

Magellan™ 2200VS
Quick Reference Guide

Datalogic USA, Inc.
959 Terry Street
Eugene, OR 97402
USA
Telephone: [phone]
Fax: [phone]
©2002-2017 Datalogic S.p.A. and its Group companies
An Unpublished Work - All rights reserved. No part of the contents of this documentation or the procedures
described therein may be reproduced or transmitted in any form or by any means without prior written per-
mission of Datalogic S.p.A. or its subsidiaries or affiliates ("Datalogic" or "Datalogic USA, Inc.”). Owners of
Datalogic products are hereby granted a non-exclusive, revocable license to reproduce and transmit this
documentation for the purchaser's own internal business purposes. Purchaser shall not remove or alter
any proprietary notices, including copyright notices, contained in this documentation and shall ensure that
all notices appear on any reproductions of the documentation.
Should future revisions of this manual be published, you can acquire printed versions by contacting your
Datalogic representative. Electronic versions may either be downloadable from the Datalogic website
(www.datalogic.com) or provided on appropriate media. If you visit our website and would like to make
comments or suggestions about this or other Datalogic publications, please let us know via the "Contact
Datalogic" page.
Disclaimer
Datalogic has taken reasonable measures to provide information in this manual that is complete and accu-
rate, however, Datalogic reserves the right to change any specification at any time without prior notice.
Datalogic and the Datalogic logo are registered trademarks of Datalogic S.p.A. in many countries, including
the U.S.A. and the E.U. All other brand and product names may be trademarks of Datalogic S.p.A. or of Dat-
alogic Group companies, registered in many countries, including the U.S. and the E.U.
All other brand and product names may be trademarks of their respective owners.
Patents
See www.patents.datalogic.com for patent list.
See the Regulatory Addendum included with your product
for additional regulatory, safety and legal information.

Quick Reference Guide i
Table of Contents
English ..........................................................................................................................1
Français ........................................................................................................................5
Deutsch .........................................................................................................................9
Italiano ........................................................................................................................13
Español .......................................................................................................................17
Portugues ...................................................................................................................21
Chinese ........................................................................................................................26
Türkçe ..........................................................................................................................29
Appendix A — Productivity Index Reporting Option ..............................................33
Appendix B — Warranty ...........................................................................................37

ii MagellanTM 2200VS
NOTES

Quick Reference Guide 1
Quick Reference Guide
Introduction
This guide offers a summary of basic scanner operation for first time users. Installers, system man-
agers and other technical personnelcan find installation, programming and further advanced infor-
mation in the Product Reference Guide. Up-to-date revisions of publications can be viewed, printed
and downloaded from the website listed on the back cover of this manual. Printed manuals can also
be ordered from your dealer/distributor.
Connection
For your convenience, Figure 1 shows scanner connections and their functions.
Figure 1. Connections
POS TERMINAL AUXILIARY PORT POWER
Connection to this port is Optional
· DC Brick Input· Label Data
· Application Download
(where appropriate)
· Test Port
· On Screen
Programming (OSP)
· Application Download
· RS-232 Handheld Scanner Input
· Auxiliary RS-232 Label Data Output
EAS Connection
Connection to this port is Optional
· Electronic Article Surveillance
Connection
Power
EAS Opening
Aux. PortScanner Host

2Magellan™ 2200VS
Operation
Scanning Items
Item bar codes are scanned by either...
• sliding or pushing items through the scan volume in a right-to-left or left-to-right
motion (see Figure 2a). This is known as “Sweep” scanning, and is the best choice for
high throughput super- and hypermarket installations where it is necessary to mini-
mize the need to grip or lift items.
• moving the bar code directly toward the scan window to be read (see Figure 2b). This
“Presentation” technique is most often used in low throughput variety, convenience
market and pharmacy applications where useable countertop space is at a premium
and “Sweep” scanning is not possible.
With FirstStrikeTM decoding software, the scanner can read most hard-to-read codes
quickly and without excess orientation.
Figure 2. Sweep and Presentation Scanning Technique
S
c
a
nne
r
a
It
em
Bar Code
Item
Bar
C
od
e
Scan Volume
Scan Volume
Items are
pushed or
slid past
scanner
S
canne
r
aSweep Technique Presentation Techniqueb

Quick Reference Guide 3
Volume/Tone Push Button
The Volume/Tone Push Button also performs multiple functions depending upon the
duration of time it is pressed:
NOTE
Volume changes made using the Volume/Tone Push Button are
lost when the scanner is powered-down and are reset to the
configured setting. If you wish to permanently change the vol-
ume, use the special programming labels in the Product Refer-
ence Guide.
Table 1. Volume/Tone Push Button Functions
Momentary (when
scanner is asleep) Wakes scanner from Sleep Mode
Alternatively, the scanner can be awakened by:
- Moving an object through the scan zone.
- Scanning with an attached auxiliary scanner.
Momentary (when
scanner is awake) Increments volume
Press the push button momentarily to increase speaker volume.
When the loudest volume is reached, a repeated press of the
push button cycles volume back to the lowest setting, then vol-
ume increases on subsequent press(es). Four volume levels are
available.
Hold, then release
when the beeper
sounds
Increments tone
Press the push button for approximately 2 seconds, then
release. Each time this is done, the beeper will sound at one of
three tones. Stop when the desired tone (high, medium or low) is
sounded.
4 Seconds Scanner Diagnostics Mode
a
This mode allows system support personnel to troubleshoot
problems with the scanner and is used to determine if it can read
bar codes. Press the button for eight seconds or cycle power to
exit Scanner Diagnostics Mode and reset the scanner.
8 Seconds Resets Scanner
b
Only system support personnel should perform a reset.
a. By standard default, this function is normally disabled to prevent accidental activation by users.
b. Users should not perform scanner resets except under the direction of trained systems support personnel.
PRESS
DURATION FUNCTION COMMENT

4Magellan™ 2200VS
Green LED Indicator
The green LED indicates scanner status as shown in the table below..
Table 2. Green LED Indications
Scanner Active
a
a. Certain functions of the LED are selectable to be enabled or disabled. Your scanner may not be programmed to display all indications.
(Normal Mode)
Scanner (Green) LED on steady and dim The scanner is ready for operation. Scanning is immedi-
ately available.
Good Read Indica-
tion
a
Scanner (Green) LED - bright flash Indicates a bar code has been read and decoded.
Program Mode
Indication
Scanner (Green) LED - Continuous flashing Indicates the scanner is in Label Programming Mode. Cycle
power to exit Programming Mode.
Sleep Mode Indi-
cation
Scanner (Green) LED flashes slowly The scanner motor and/or laser have automatically
switched off and the unit has entered Sleep Mode due to
extended inactivity.
Host Disabled
Scanner (Green) LED 1-second off, 1/10-
second on Host has disabled scanning.
Field Replaceable
Unit (FRU) Warn-
ing (Error Mode)
Audible low tone 1 second. LED flashes con-
tinuously. Serves notice that a fatal FRU failure has been detected.
Call systems support for service.
FRU Indication
Scanner (Green) LED flashes a coded
sequence in concert with the speaker.Occurs ONLY upon Volume/Tone button push following a
FRU warning. Enables service technicians to identify FRU
failures.
LED INDICATION DURATION COMMENT

Quick Reference Guide 5
Introduction
Ce guide présente une synthèse du fonctionnement de base du scanner à l'attention des
utilisateurs novices. Les installateurs, les administrateurs de système et autres person-
nels techniques pourront obtenir des informations sur l'installation, la programmation
ainsi que d'autres indications plus avancées dans le Guide de référence du produit. Il est
possible de consulter, d'imprimer et télécharger des mises à jour des publications à partir
du site de à l'adresse reportée sur la couverture postérieure de ce manuel. Il est également
possible de commander des manuels imprimés auprès de votre vendeur/distributeur.
Raccordement
Pour vous aider, consulter la Figure 1 qui illustre les raccordements et les fonctions du
scanner.
Figure 1. Raccordements
Port auxiliaire Alimentation
Le raccordement à ce port est
facultatif
· Entrée Brick CC
· Données étiquette
· Téléchargement de
l'application (le cas
échéant)
· Port d'essai
· Affichage de la programmation (OSP)
· Téléchargement de l'application
· Entrée scanner à main RS-232
· Sortie auxiliaire RS-232 données
étiquette
Raccordement EAS
Le raccordement à ce port est
facultatif
· Système de surveillance
électronique d'articles (EAS)
Raccordement
Power
EAS Opening
Aux. PortScanner Host
Terminal
d'encaissement (POS)

6Magellan™ 2200VS
Fonctionnement
Lecture d’articles
Les codes à barres des articles sont numérisés selon deux procédures soit…
• en faisant glisser ou en poussant les articles à travers le volume de lecture de la
droite vers la gauche ou de la gauche vers la droite (voir Figure 2a). Il s'agit du mode
de lecture " Transfert " (par balayage) qui constitue la meilleure solution pour la moy-
enne et la grande distribution, où il faut limiter au maximum la saisie ou le soulève-
ment des articles.
• en déplaçant le code à barres directement en face de la fenêtre de numérisation afin
de le soumettre à la lecture (voir Figure 2b). Ce mode de lecture par " Présentation "
est surtout utilisé pour les applications dans les pharmacies, les magasins de prox-
imité, les points de vente à faibles transactions où l'espace utilisable sur le comptoir
est réduit et le mode " transfert " est par conséquent impossible.
Grâce au logiciel de décodage FirstStrikeTM, le scanner peut capturer rapidement et avec
une orientation minime la plupart des codes de lecture difficile.
Figure 2. Mode de lecture " Transfert " et " Présentation "
S
c
a
nne
r
a
Volume de
lecture
Volume de
lecture
Les articles
sont poussés
ou glissés
devant le
scanner
S
canne
r
aMode Transfert Mode Présentationb
Code à
barres de
l'
a
r
t
t
i
c
l
e
t
C
ode
à
barres de
l'article