Dataprobe iBoot-DC User manual

Web Enabled
Power Switch
October 2018
1.Table of Contents
1. Table of Contents 1
2. General Description 2
3. Hardware Installation 3
4. Initial Configuration 6
5. Web Browser Operation 8
6. Web Setup 11
7. iBoot Cloud Service 18
8. Command Line Interface 21
9. DxP Protocol 25
10. Firmware Upgrades 25
11. Troubleshooting 26
12. Specifications 27
13. Technical Support and Warranty 28
Congratulations on purchasing the best
network controlled power switch available.
The iBoot-DC provides you the ability to
reboot crashed devices with the click of a
mouse. Be sure to read up on all the
features of the iBoot-DC Including:
Web Based setup and control
iBoot Cloud Service: Control all your
iBoots from one web portal.
AutoPing: Automatic monitoring and action
for failed equipment.
Event Scheduling for real-time power
control.
Telnet setup and control
Management Utility: Easy Setup,
Firmware upgrades and Reset to Factory
Default.
Easy Software Integration: Protocols to
build your own custom applications.
Local Link Multicast Name Resolution:
Use to access on supporting networks.
Reboot Only Mode: Prevents accidental
switching off to ensure continuous operation.
iboot-dc_v181024e

iboot-dc_v181024e iBoot-DC Page 2
2.General Description
The iBoot-DC is a network attached, IP addressed, web controlled AC power switch. Anyone with a web
browser can access iBoot-DC to perform power On, Off or Power Cycle (Reboot or Power Burst).
iBoot-DC uses two levels of password for security.
iBoot-DC features international standard IEC320 connections and is compatible with power mains
worldwide. A simple Web browser interface makes it easy to control power from anywhere in the world
with a click of a mouse. iBoot-DC also supports Telnet for text commands, as well as Dataprobe’s
Exchange Protocol (DxP) for interfacing to a variety of Dataprobe products and custom software
development.
2.1. Uses for iBoot
Remote reboot of any device, routers, servers, kiosks, etc. The device to be rebooted need not be
network attached.
Secure sensitive devices by keeping them powered off when not in use. This prevents hackers from
seeing them at all times.
Power down equipment when not needed for power savings and to save on wear and tear.
Power up alert devices like sirens, lamps, messages; or control environmental system like heaters,
coolers pumps, etc.
2.2. Multiple Control Options
In addition to the Web control capabilities, iBoot-DC features several other means to operate automatically
or under computer control.
URL Control: You can send a single URL to the iBoot-DC containing all the information necessary to
query or change the power status. This makes it easy to create a single button on your desktop or embed
into a batch file or script.
AutoPing: The AutoPing feature allows iBoot-DC to automatically detect failed equipment and perform a
timed reboot or other power control function (like turning on an indicator or siren). You set 1 or 2 IP
addresses to be periodically pinged. When iBoot-DC no longer detects a response from the address(es),
the programmed power control function is actuated.
Telnet: iBoot’s Command Line Interface (CLI) allows direct control and setup through Telnet.
Dataprobe Exchange Protocol (DxP): Use this status and control protocol to build custom applications to
manage iBoot, or use our available utility program to build batch files or command line routines. Download
API and utilities at dataprobe.com/support-iboot-dc

iboot-dc_v181024e iBoot-DC Page 3
3.Hardware Installation
3.1. Ethernet Connections
iBoot-DC supports 10/100 Ethernet using the cable supplied, or other
suitable unshielded twisted pair (Cat 5) cabling. Activity (green) and
100Mb (amber) LEDs on the network connector indicate when the
network connection is properly established and when the connection
is 100 Mbit/s.
3.2. DC Power Connections
iBoot-DC uses screw terminal connections for the DC input and
switched output connections. The screw terminals can be removed to facilitate connection and cable
fabrication.
Maximum Operating Current
5.0 to 29.9 VDC
12 Amps
30.0 to 48.0 VDC
2 Amps
The Positive lead is switched. When ON, the power will be at the NO connection. When OFF, the power
will be at the NC connection.
The chassis ground is optional and not switched.
An LED Indicator market Output will be on when the power to the NO connection is On.
Connect 10/100 Ethernet

iboot-dc_v181024e iBoot-DC Page 4
3.3. Connecting Negative Voltages
iBoot-DC will accept a negative (relative to ground) power source i.e. -48VDC. Insure the power leads are
connected so that "+" terminal voltage is positive RELATIVE to the "-" terminal voltage.
Do Not connect Chassis Ground when using –VDC Power.
3.4. Mounting Options
iBoot-DC is suitable for desktop or shelf mounting. A
mounting kit for wall and DIN rail mounting is available.
Order part:
1920034 Mounting Kit for iBoot Series
Remove all cables from the unit prior to
installing or removing any mounting hardware.
1920033 Mounting Kit
iBoot Series

iboot-dc_v181024e iBoot-DC Page 5
Installing the Wall Mounting Kit
DIN Rail Mounting
1. Remove the
four mounting
screws from
the underside
of the unit.
Do not
disassemble
the unit.
1. Install the
Wall
Mounting Kit
as shown.
2. Install the wall
mounting ears
to the unit
using the
screws
removed in
Step 2
2. Install the
DIN rail clips
using the
four screws
provided.
3. The unit is
ready for wall
mounting.
3. Ready for
DIN rail
mounting.
4. Use M3 or #4
screws (not
included) for
attachment to
suitable surface

iboot-dc_v181024e iBoot-DC Page 6
4. Initial Configuration
4.1. Auto-Configuration
If your network supports Dynamic Host Configuration
Protocol (DHCP), the iBoot will be automatically
assigned an IP Address and be ready to use. You
can discover the IP Address through your
Server/Router, or use Dataprobe’s Device
Management Utility (DMU).
4.2. Device Management Utility
The DMU is available online at
dataprobe.com/support-iboot-dc/, provides the
easiest means to find and configure your iBoot-DC
for use. It can:
Discover all the iBoots on your network,
Display the current IP address of each
Allow setting of an IP address
Reset to Factory Defaults
Upgrade the Firmware of the iBoot-DC
Obtain and use the DMU:
1. Download the latest version of the DMU at
dataprobe.com/support-iboot-dc/
2. Run DMUSetup.exe
3. Run the DMU
Note: The IP address can only be set within the first
two minutes of powering up the iBoot-DC or pressing
the reset button (see Section 11). The Setup Utility
will only work with iBoots on the same physical
subnet as the PC.
Once the DMU is run, click on Device | Discover to
display all the iBoots on your network. The DMU will
display the Location Name of the iBoot, The product
ID and Version Number, the current IP Address, and
the MAC Address. Factory defaulted iBoots will
display with the name iBoot-DC-xxxx where the
xxxx are the last 4 segments of the MAC address,
and have the factory default IP address of
192.168.1.254, or as set by DHCP.
The IP address field also indicates the port for web
access that is used by the iBoot. The standard port
for web browser control is factory default Port 80.
DMU Discovers Dataprobe Devices
on your Network
Enter New IP Address for iBoot
IP Address Successfully Set

iboot-dc_v181024e iBoot-DC Page 7
Change the IP Address
1. Click on the row containing the iBoot-DC to be set. The row will become highlighted.
2. From the menu select Set | Network Settings
3. Select the IP Mode DHCP if you want the network to assign parameters
4. Select the IP Mode Static if you want to define all network parameters manually.
5. Click OK when done.
Once the IP Address is set, other all other operational features of the iBoot-DC can be set up. Click on
Discover again to refresh the display, highlight the desired iBoot-DC and click on Manage | Launch
Browser. See Section 6 to configure the iBoot.
The DMU can also be used to return an iBoot-DC to its Factory Default condition. This can be used to
recover an iBoot-DC with a lost password. Highlight an iBoot-DC from the display and select Set | Factory
Defaults. Using the Utility to reset defaults will not change the network settings allowing you to re-access
the unit. You can also use Set | Admin Password to reset only the admin password parameter back to
default. These reset options must be done within the first two minutes of powering up the iBoot or pressing
the reset button.
4.3. Other ways to set the IP Address
1. Web Browser via the Set-up Page –See Section 6.2
2. Command Line Interface See Section 8

iboot-dc_v181024e iBoot-DC Page 8
5.Web Browser Operation
5.1. Password Protection
iBoot-DC uses two username/password credential sets, one for power
control only (User) and one that also provides access to the setup
functions (Admin). This configuration can be changed to require
Administrator credentials at all times or allow unsecured User level
control. See section 6.8.
Default Credentials:
Role
Username (fixed)
Password (settable)
Administrator
admin
admin
User
user
user
Open your browser and enter the IP address of iBoot-DC into the address bar. If you have changed the IP
address by any of the methods described or used DHCP, enter that address, otherwise, use the default IP
address 192.168.1.254
Enter the username and password when prompted. When the proper username/password is received the
Control and Status Page is displayed.
iBoot-DC uses an inactivity timer for security. This timeout is user selectable from 0 to 99 minutes.
Setting to zero disables the timeout feature. When there is no activity for the set time in minutes, the user
is automatically logged out and the username and password will need to be entered again for access. This
is to prevent accidental lockout by leaving the user logged in.
As the iBoot-DC allows only one Web user logged in at any time, use caution when disabling the
timeout feature, as it is possible to lock out other users by forgetting to logout. Closing the
browser will not log the user out and will lock out web access. If you do become locked out,
access the iBoot-DC via Telnet and reboot the unit, or press the reset button (see Section 11).
5.2. Mobile Browser Support
iBoot uses adaptive web pages to accommodate desktops, tablets
and smartphones. No additional apps are needed to access the
complete features.
Enter Username and Password

iboot-dc_v181024e iBoot-DC Page 9
5.3. Control and Status Page
Once the user is validated, the Control and
Status page is displayed. (Only one person
can be connected to the iBoot-DC at a time.).
This page provides automatic updates every
5 seconds.
To control the power, click on the appropriate
button. During power cycling, the Power
Status bar will indicate the temporary status,
with a blue background. Once the cycle is
complete, the status bar will revert to its
original condition. To abort a power cycle,
click on either Power On or Power Off
buttons.
If the AutoPing feature is in use, the page will
also display the current status, OK or Failed,
for each AutoPing in use, with a counter of
how many times action was triggered. If
connecting with the Admin credentials, reset
buttons for the Trigger counter is provided.
If the iBoot-DC is connected to a time server (see Section 6.3), The Home page will also show the five
most recent history events, including the Outlet, Action, User and Time/Date of each event. The iBoot-DC
holds the last 32 events in memory. The user can access a complete history webpage, download the
history in a .csv file, or clear the history.
Navigation Menu:
Refresh: Use the Refresh button to obtain the latest status of iBoot. Using your browser's refresh button
can lead to inadvertent power switching. If an NTP server is being used, the time of the last refresh will be
shown in the upper right corner.
Logout: When you are finished with iBoot, click on
Logout. A Goodbye page will be displayed. This
page has a URL link to re-connect with the iBoot.
The linkback URL is user settable. If no linkback is
set, the hyperlink will be the unit’s IP Address.
Setup: To access the Setup page, the administrator
credentials are required. When logged in as User, the challenge for Administrator credentials will be
displayed.

iboot-dc_v181024e iBoot-DC Page 10
5.4. URL Control
iBoot-DC can be controlled directly by sending a completely formed URL through a browser window or
HTTP command. The URL syntax for control is:
http://<address>?s=<status>&t=<time>&u=<user>&p=<password>
Where:
<address> =
the IP Address of the device, or DNS name that resolves to the IP Address,
Including any HTTP Port if not standard 80
<status> =
The status to change the outlet to:
0 = Off
1 = On
2 = Query only, no outlet change
<time> =
The amount of time to cycle
<user> =
user or admin depending on password used
<password> =
password associated with user
Syntax notes:
The order of the variables is not significant.
The user and password are not required when Auto-Login feature is enabled
(see Section 6.8 for security options.)
Examples:
http://192.168.1.254?s=1&u=user&p=user Turn the outlet on for the default user.
http://192.168.1.254?s=0&t=5 Reboot for 5 seconds with Auto-Login
http://192.168.1.254:8080?s=2&u=admin&p=admin Return status using http port 8080
URL Command Responses
iBoot-DC will return an response to a URL command as follows:
<location id> <status>
The full http response is
<!DOCTYPE html PUBLIC "-//W3C//DTD XHTML 1.0 Transitional//EN"
"http://www.w3.org/TR/xhtml1/DTD/xhtml1-transitional.dtd">
<html xmlns="http://www.w3.org/1999/xhtml">
<head>
<meta http-equiv="Content-Type" content="text/html; charset=utf-8" />
<title>iBoot Status</title>
</head>
<body>
<locationID>iBoot-DC</locationID>
<status>OFF</status>
</body>
</html>

iboot-dc_v181024e iBoot-DC Page 11
6. Web Setup
iBoot-DC setup section consists of several pages. Access any page via the buttons on the left of the page.
Each time a setting is changed click on the Save button for that page to save the changes before moving
to the next page.
6.1. Device Settings
Location ID: Set a 20 Character name to be
displayed on the top of the Home page. This
assists in identifying which iBoot-DC is being
accessed. The Location ID is used with LLMNR
and a reboot will be required to apply the new
name See section 6.10 to learn more about
LLMNR.
Cycle Time: 1 to 999 seconds power cycle time.
This is the length of time the power will be off
during a reboot, or on during a power burst.
Disable Off: When checked, this will not allow the
iBoot-DC to turn off. Cycle will cause a reboot, but
no command will leave the power in the OFF state. Unchecked the unit will function normally and allow an
off outlet. (See section 6.9)
Initial State: The outlet can be set to the state it will assume when the iBoot-DC is powered up or reset.
The choices are: On, Off and Last, meaning the state it was in when the power was removed or reset
commenced.
Upgrade Enable: Check this box to allow remote firmware upgrades of the iBoot-DC. When this box is
unchecked, firmware upgrades will not be allowed.
Auto Logout: This setting sets the automatic logout for inactivity on both the web and telnet users. It can
be set from 0 to 99 minutes. 0 disables the Auto Logout feature.
As the iBoot-DC allows only one Web user logged in at any time, use caution when disabling the
timeout feature, as it is possible to lock out other users by forgetting to logout. Closing the
browser will not log the user out and will lock out web access. If you do become locked out,
access the iBoot-DC via Telnet and reboot the unit, or press the reset button.
6.2. Network Settings
MAC Address: the Mac address of the unit is displayed for reference.
IP Mode: Select Static to set the IP address using
the fields below, or DHCP to allow a DHCP server
to set the IP Address.
IP address: Enter a static IP address. This will be
automatically set if using DHCP
Subnet Mask: Enter the Subnet Mask. This will be
automatically set if using DHCP
Gateway: Enter the Gateway. This will be
automatically set if using DHCP
DNS: Enter the Domain Name Server address. This will be automatically set if using DHCP.

iboot-dc_v181024e iBoot-DC Page 12
6.3. Advanced Network Settings
HTTP Port: This setting is used to
allow access to iBoot-DC on a port
other than the Web standard Port 80.
If the port is changed, you will need to
identify the port number when you
enter iBoot's IP address into your
browser. If the new port is 8080 then
use the address
http://192.168.1.254:8080.
Linkback URL: This setting allows
control of the hotlink displayed on the
Goodbye page. It allows use of the
public IP address or DNS name
instead of the internal IP Address of
the iBoot-DC, which is the default
setting. If this setting is left blank, the
hotlink will be the IP Address of the
unit. Enter up to 128 characters.
Telnet Port: This setting is used to
allow access to the iBoot-DC via telnet by ports other than standard 23.
DxP Port: This setting is used to allow access to the iBoot-DC via Dataprobe Exchange Protocol (DxP) via
ports other than standard 9100.
Enable Cloud Services: This setting enables the iBoot for iBoot Cloud Services (iBCS). iBCS allows the
iBoot to be monitored and controlled from a web portal from any browser. It allows multiple iBoots to be
managed from a single portal. For a complete description of iBCS and setup instructions, see Section 7.
Note: All of the TCP/IP Settings require a reboot of the iBoot-DC, after clicking Save. A Reboot
button will appear at the bottom of the page. The new settings will not take effect until the unit is
rebooted. Reboot will not affect the power position of the iBoot-DC. Upon Clicking Reboot, the
Rebooting page is displayed with a link to re-login.
6.4. Time Setup
The Advanced Network Setup page also allows setup of the Time server, required for Scheduling and
Logging functions.
Enable: Enable or Disable the use of the Time Server with this checkbox
Time Server: Enter the Time Server. The default is time.nist.gov
Time Zone: Enter the Time Zone (-12 to +12) relative to GMT
DST Enable: Enable or Disable the use of Daylight Savings Time with this checkbox
DST Start / Stop: Enter the start and stop parameters of Daylight Savings Time here.

iboot-dc_v181024e iBoot-DC Page 13
6.5. AutoPing
The AutoPing feature allows iBoot-DC to
automatically detect failed equipment and perform
a timed reboot or other power control function (like
turning on an indicator or siren). You set one or
two IP addresses to be periodically pinged. When
iBoot-DC no longer detects a response from these
addresses, the programmed power control
function is actuated. The two addresses can be
AND or OR linked so that both (AND) or either
(OR) need to fail in order to take the selected
action.
Examples:
Use Auto-Ping as network monitor: iBoot-DC is
installed with the device to be rebooted, but pings
a remote host to test the communication channel.
Ideal for: DSL & Cable Modem Verification Use
AutoPing as server monitor: iBoot-DC is installed
with the device it monitors and automatically
reboots if there is no response. Ideal for: Kiosks &
Servers.
AutoPing as an Alert Generator: iBoot-DC
monitors network device and powers up alarm,
environmental response or redundant system.
Ideal for: Hot Standby Servers, Environmental
Control, Alert for any Network Failure.
6.6. AutoPing Settings
Address: Enter the IP address of the device, or
domain name to be pinged. To enter the second
address and settings, select AND or OR for the A/B
Logic.
Ping Frequency: Enter 1 to 999 seconds. The ping
will go out to the selected device this often.
Fail Count: Enter 1-999 times the ping needs to fail
consecutively before the selected action is taken.
When the fail count has been reached, the AutoPing
action will be triggered.
Mode:Select from Single, AND, OR. With AND,
both AutoPings need to exceed their fail count to
trigger the Action. With OR, the Action will be
triggered if either AutoPing fails.

iboot-dc_v181024e iBoot-DC Page 14
Action: Select from
None
AutoPing is paused. No Ping tests will be performed.
Power On –Latch
Upon triggering, iBoot-DC will power on and remain so until changed via the
web, telnet, DxP, etc.
Power On –Follow
Upon triggering, iBoot-DC will power on. When the ping response returns,
iBoot-DC will power off.
Power Off –Latch
Upon triggering, iBoot-DC will power off and remain so until changed via the
web, telnet, DxP, etc.
Power Off –Follow
Upon triggering, iBoot-DC will power off. When the ping response returns,
iBoot-DC will power on.
Cycle
Cycle Times
Upon triggering, iBoot-DC will cycle the power. If Power Cycle does not
result in the ping response the iBoot-DC can cycle again. The number of
times the iBoot-DC will cycle is set by the Cycle Times setting. To have the
iBoot cycle power 3 times to get the system to respond again, set the Cycle
Times to 3.
Restart: This setting delays the restart of the AutoPing tests after the Action is completed. This setting
allows time for the boot sequence of the failed device to complete.
With AutoPing operational, the main iBoot-DC page will display the current status of this feature. The
status will be OK to indicate that iBoot-DC is receiving responses to the ping, or that the fail counter has
not yet been exceeded.
If the fail count has been exceeded, the status will change to FAIL. The Trigger Counter indicates the
number of times the AutoPing action has been triggered. A counter reset button is provided.
Note: All of the AutoPing Settings require a reboot of the iBoot-DC, after clicking Save. A Reboot button
will appear at the bottom of the page. The new settings will not take effect until the unit is
rebooted. Reboot will not affect the power position of the iBoot-DC. Upon Clicking Reboot, the
Rebooting page is displayed with a link to re-login.
6.7. Event Scheduling
iBoot-DC can schedule up to eight reoccurring
power events. Set the starting date and time,
plus the action to be taken and any repeat
cycle for each.
To enable the time scheduling function set the
network time server in Advanced Network
Setup, Section 6.3.
Once the time server is active, scheduled
events can occur. Up to eight independent
scheduled events can be programmed.
Date: Set the initial date for the event. The format for the date is mm/dd/yyyy.
Time: Set the initial time for the event. The format for the time is hh:mm with hours in 24 hour format.
Repeat: Set the repeat multiplier, if desired. Set the number from 0 to 999 and either Days, Hours, or
Minutes. To have the schedule repeat every two days, set this number to 2 and selection to Day(s).

iboot-dc_v181024e iBoot-DC Page 15
Action: Set the event Action; On, Off or Cycle.
Enable: When this box is checked, the event will occur at the programmed time. When it is unchecked, the
event will not occur, but the next calculated event time will be displayed.
Clear: Delete the scheduled event.
Click Save to save the current settings. Click Reset to delete any unwanted changes.
6.8. Password Settings
The iBoot-DC supports three modes of user and
password operation.
Login Required: This mode supports both User
and Admin users. Each user has a settable
password.
Auto Login: This mode does not require a
username of password for the User level operation.
No login challenge will be required for any mode of
operation, until any setup function is requested.
The Admin username and password is required for
any admin functions.
User Disabled: There is no User account. The Admin username and password will be required for
operation and setup functions across all modes of operation. This is the factory default mode.
Two passwords are used by iBoot. In the Login Required mode, The User Password allows access to the
control of iBoot, but not to the Setup functions. Clicking on the Setup button allows the Administrator to log
in. Passwords can be up to 20 characters long and are case sensitive.
Enter the current password then the new password twice to confirm.
Default Credentials
Role
Username (fixed)
Password (user set)
Administrator
admin
admin
User
user
user

iboot-dc_v181024e iBoot-DC Page 16
6.9. Disable Off
This new feature in version 1.5 and above insures that the power to the controlled device will always be on
whenever possible. No accidental turning or leaving the power off is possible.
To use the “Disable Off” feature
WEB –On the Setup > Device page check the enable box next to the Disable Off: option and Save.
CLI - telnet to the unit and issue the Command Line Interface command.
set disable off yes
Use the following to determine the current status of the feature.
get disable off
The response will be Disable Off: Yes or Disable Off: No
Yes will indicate it is enabled and No will indicate it is disabled. By default, the feature is disabled.
To stop using this feature issue the command
set disable off no
When the feature is enabled, the following will occur:
If the outlet is Off at the time the feature is enabled, the outlet will turn On
Initial state will be programmed for On
Initial state will not allow programming for Off or Last
If AutoPing action programmed for On-Follow, Off-Latch or Off-Follow, the autoping action will be
reprogrammed as None
AutoPing action will not allow programming for On-Follow, Off-Latch or Off-Latch
If a Schedule Settings event has action for Off, it will be reprogrammed for On
Schedule Settings will not allow programming for action Off
Web page will not show the “Power OFF” button
Web Page will not process an HTTP POST for Off.
URL control will not process an unqualified off status request (s=0) A qualified off status request with a
time setting (s=0&t=1) of 1 or more will be processed allowing for URL control to cycle off, then back
on
URL control will not process a qualified on status request with a time setting (s=1&t=1) of 1 or more
(disabling URL control to cycle on then off)
DxP control will not process an Off command
DxP control will not process a pulse on command. pulse on commands end with outlet off
DxP control Pulse Off commands, while in progress, will not allow cycle commands to override them.
(avoiding potentially having a completed cycle end as off)
Cycle commands, while in progress, will not allow new cycle commands to override them.
(avoiding potentially having a completed cycle end as off)
Command Line Interface (CLI) control will not process “set outlet off”
If cloud control is enabled, the Off command will not be processed.
Disabled
When the feature is disabled, all the modes that can turn the power off will be available and functioning.

iboot-dc_v181024e iBoot-DC Page 17
6.10. Local Link Multicast Name Resolution (LLMNR)
The Link-Local Multicast Name Resolution (LLMNR) is a protocol based on the Domain Name System
(DNS) packet format that allows hosts to perform name resolution on the same local link.
On most networks you will be able to access the iBoot-DC by its device name when on the local network.
By default the name is iBoot-DC-xxxx where the xxxx is the last 4 segments of the MAC address for your
iBoot-DC. When you reprogram the name of the device, a reboot is required to apply the new name as the
LLMNR for the device.
The LLMNR name does not allow spaces. If using the LLMNR feature to access the iBoot-DC, do not use
a space in the name. When accessing the device type the complete URL including the http:// if you need
to avoid searching the internet for the name. ( http://iBoot-DC-xxxx )

iboot-dc_v181024e iBoot-DC Page 18
7.iBoot Cloud Service
iBoot Cloud Service (iBCS) allows customers with iBoot to access and control multiple iBoots in multiple
locations from a single portal with a single sign-on.
iBCS will not only make using iBoots easier, by consolidating all units into one sign-on and interface; it will
also enhance the number of situations where iBoot can be deployed.
Customers with Dynamic IP addressing will always be able to access their iBoot from any location.
Customers that do not allow in-bound connections can access their iBoots.
Service providers can manage multiple customer accounts with diverse security configurations
7.1. iBCS Setup & Operation
Use of the iBoot Cloud Services requires the iBoot to be
configured to access the Internet. Please review the
installation and configuration procedures to insure
proper setup.
a. Establish Account with iBoot Cloud Server
Visit http://iboot.co from your browser
Click on Register
Complete the information
Confirm Registration by clicking on the link
provided in the email.
b. Insure Proper iBoot-DC Firmware
iBoot Cloud Service requires version iBoot-DC Firmware version 1.21.99 or greater. Check the bottom
of any web page of the iBoot for the firmware version. If needed, download and install the proper iBoot
Firmware from http://dataprobe.com/support-iboot-dc/ and install as instructed in Section 10
c. Enable Cloud Services on iBoot
Log into the iBoot with Administrator rights
Go to the Advanced Network Setup page

iboot-dc_v181024e iBoot-DC Page 19
Click on the checkbox Enable Cloud Services:
Within 30 seconds, an 8 character activation code will appear.
This code is also a hotlink to the Cloud Service.
d. Register iBoot with Cloud Account
Click on the Activation code to register the iBoot
with the Service.
You will be re-directed to the Service. Log-in
with your account and the iBoot will be
automatically registered with your account.
Alternatively, you can log in to the Service and
click on Add Device and enter the activation
code in the field provided.
Congratulations. You are now on the cloud.
e. iBCS Main Page
The iBCS main web page provides a menu bar
with the following options:
Devices: List all registered iBoot units, ordered
by their Name. Click on any iBoot line to
manage that unit.
Locations: Group all iBoots by location. Click
on any location to display or hide all the iBoots
at that location.
Account: Display and edit account information
and obtain account access history.
Help: Links to the iBoot Cloud Forum and
Dataprobe support pages.

iboot-dc_v181024e iBoot-DC Page 20
f. Control Power from the Cloud
The status screen will detail all the
iBoots registered with the cloud. You
can add locations and group iBoots
by location.
Each iBoot displays the power status
and AutoPing if configured.
Click on the box that holds the
Activation Code for the device you
just entered. A modal box will
appear with options to rename the device, move the device to a defined location or delete the device.
Give the device a name, and Click Rename Device.
The remainder of the modal is very similar to the iBoot web page.
Select Power ON, Power OFF or Cycle Power.
g. Assign Names and Locations
You can establish multiple locations and assign each
iBoot to a location. You can also name each iBoot
independently from the Device Name that is displayed
on the iBoot web page. To add locations, click on the Locations button on the menu bar, and then click
Add Location. Name the location and click the Add Location button.