Dataprobe RSS-16 Owner's manual

1. GENERAL
Dataprobe’s RSS Redundancy Switch Systems provide high density relay based A/B switching for multiple
circuits. Two chassis systems are available to accommodate large and small applications.
Each system uses the same plug in cards, providing switching for up to 32 circuits in a single chassis. Both
systems offers gang (simultaneous) switching as well as individual control of each A/B card.
Dataprobe's RSS Series rack mounting chassis are available in two models; RSS-16 and RSS-3.
The RSS-16 supports up to 16 AB switch cards, 2 control interface cards and 2 internal power supply modules
in a compact 4U high, 19 inch chassis.
The RSS-3 supports up to 3 AB switch cards, 1 control interface card and 1 internal power supply module, in a
1U chassis with removable rack mount brackets.
Both chassis also provides access to local control switches for each of the A/B switch cards and viewing of their
A/B status LEDs.
Information in this manual applies to both systems except where specifically indicated.
Power Supply modules are available for 100 -240 VA/C , 50-60Hz and 48 VDC power sources. Two modules
can be installed in the chassis. In addition, external 24 V dc power supplies are available as an alternative to
the internal power module or to provide redundant power.
RSS Series
Redundancy Switch Systems
Installation and Operation

RSS_v180808n RSS Series Page 2
Table of Contents
1. GENERAL 1
Table of Contents 2
2. Chassis 3
2.1. RSS-16 Chassis 3
2.2. Important Notice: 3
Avis Important: 3
2.3. RSS-3 Chassis 4
2.4. Power Supply Indicators 4
2.5. A/B Card Status Indicators 5
2.6. A/B Card Manual Toggle Switches 5
2.7. Gang Control Switches RSS-16 5
2.8. Filler Panels 5
3. Power Supplies 6
3.1. Power Supply 1930084 6
3.2. Power Supply 1930083 7
3.3. Power Supply 1930086 7
3.4. Power Supply Installation 8
3.5. 24VDC Power Connection 9
4. IPC-16-R Control Card 10
4.1. Dual Control Cards RSS-16 10
4.2. IPC-16-R Installation 11
4.3. Serial Port 11
4.5. Command Line Interface 12
4.6. Telnet 12
4.7. Serial Port 12
4.8. SNMP 12
4.9. Command Line Interface 12
4.10. Configuration – IPC-16-R 13
4.11. Setting other Parameters 14
4.12. Operation 15
4.13. Command Line Interface 16
4.14. Web Browser Operation 21
4.15. SNMP Manager Control 23
4.16. Escape Sequence Control 23
5. IPC-1-R Network Gang Control Card 25
5.1. IPC-1-R Configuration 25
5.2. Web Browser Operation 27
5.3. Setup Page 29
5.4. AutoPing 31
5.5. 31
5.6. Troubleshooting 32
5.7. Updating Firmware 32
6. IOC-16-R 16 Channel I/O Control Card 33
6.1. Installation 33
6.2. Status and Control Connector Pinouts 33
7. IOC-3-R Channel I/O Control Card 35
7.1. IOC-3-R Card Installation 35
7.2. IOC-3 A/B Switch Control Connections 35
7.3. Gang Switching Applications 35
8. Basic A/B Cards 37
8.1. A/B Cards, Current Models 37
8.2. Installation 38
8.3. Configuration 38
8.4. Indicators 39
8.5. Manual Switches 39
8.6. Relays 39
8.7. Interface Wiring 39
9. MIB Definitions 42
9.1. Trap Definitions 43
10. WARRANTY 44

RSS_v180808n RSS Series Page 3
2.Chassis
2.1. RSS-16 Chassis
Item # 1150101
The RSS-16 Chassis mounts in standard 19” equipment cabinets.
Power supplies, control cards and switch cards install from the rear of the chassis. Install each card with the
components facing left. The chassis and cards are keyed to prevent incorrect insertion. Switch cards may be
inserted and removed with the power on (hot insertion/removal). Cards are secured in chassis with screws at the
top and bottom of each panel.
19" W x 7.0" H x 7" D Weigh 12.5 Lbs (w/o cards)
2.2. Important Notice: Avis Important:
An appropriate fire and electrical enclosure should be provided in the
end product for the top and bottom openings.
Un incendie approprié et armoire électrique doivent être fournis
dans le produit final pour les ouvertures supérieure et inférieure.
If any of the card slots, including power supply slots, are not being
used they are to be replaced with the appropriate blank plates so that
the enclosure is completely closed.
Si l'une des fentes de cartes, y compris les emplacements
d'alimentation, ne sont pas utilisés, ils doivent être remplacés par
les plaques vierges appropriées pour que l'enceinte est
complètement fermé.
Operators are not permitted access to the internals of the chassis.
Only Service person shall remove covers and replace cards.
Les opérateurs ne sont pas autorisés à accéder aux éléments
internes du châssis. Seulement personne Service doit enlever les
couvercles et remplacer les cartes.

RSS_v180808n RSS Series Page 4
Note for serviceperson/technician: The symbol left
(exclamation point in a triangle) indicates that energy
hazards could be possible on the backplane. The
symbol is located on the inside of the chassis near
every other A/B switch connector.
This symbol located by the power inlets indicates
that these devices may have multiple power sources.
It is required that all power sources shall be
disconnected before servicing to avoid shock hazard
Remarque pour préposé à l'entretien / technicien: Le symbole à
gauche (point dans un triangle d'exclamation) indique que les
dangers de l'énergie pourrait être possible sur le fond de panier. Le
symbole est situé à l'intérieur du châssis à proximité de chaque
autre connecteur du commutateur A / B.
Ce symbole situé par les entrées d'alimentation indique que ces
dispositifs peuvent avoir plusieurs sources d'alimentation. Il est
nécessaire que toutes les sources d'alimentation doivent être
déconnectés avant l'entretien pour éviter tout risque de choc.
2.3. RSS-3 Chassis
Item # 1150102
The RSS-3 Chassis mounts in standard 19” equipment cabinets. Rack mounting brackets provided, can be
attached to the chassis sides for front or rear rail installations, or removed for non rack applications.
Power supplies, control cards and switch cards install from the rear of the chassis. Install each card into the guide
slots with the components facing upwards. The chassis and cards are keyed to prevent incorrect insertion. Switch
cards may be inserted and removed with the power on (hot insertion/removal). Cards are secured in chassis with
screws at right and left of each panel.
19" W x 1.75" H x 7" D Weigh 3.5 lbs. (w/o cards)
2.4. Power Supply Indicators
The Chassis has two LED indicators that display the current status of two power supply sources. These are
designated PS-1 and PS-2. LED on Indicates the power supply source is connected.
PS-1 Internal Power Supply Module, or External Power Supply #1
PS-2 Internal Power Supply Module, or External Power Supply #2

RSS_v180808n RSS Series Page 5
2.5. A/B Card Status Indicators
Each A/B switch card has LED indicators that can be viewed from the front panel of each chassis. When an A/B
Switch is installed, the LEDs for that slot will be either A or B to indicate the status of the card. With no A/B Switch
installed, there will be no LEDs to view.
2.6. A/B Card Manual Toggle Switches
Each A/B switch card has al toggle switch for local control. The switches are accessed thru slots in the chassis
front panel. These are momentary switches. Move the toggle up to select the A position of the card or down for the
B position. With no card in a slot, there will be no toggle switch.
2.7. Gang Control Switches RSS-16
The RSS-16 chassis has three pushbutton switches for simultaneously controlling all A/B cards in the chassis. To
perform control, hold down the pushbutton marked Enable while pressing either the A or B pushbutton to operate
the switches.
In multi-chassis systems, the master chassis (containing the control card), these pushbuttons will operate all A/B
Cards in the system. In subsequent chassis, these pushbuttons will operate only the cards in that specific chassis.
2.8. Filler Panels
Blank Filler Panels - #1920128 Blank panels are available for covering and shielding unused card slots. Filler
panels are required for unused slots to meet UL and CE requirements.

RSS_v180808n RSS Series Page 6
3.Power Supplies
The RSS chassis supports both internal and external power supplies, allowing a wide assortment of combinations
for flexibility and redundancy. Internal power modules are available to support worldwide A/C power, -48VDC and
+24VDC external power supplies. External power supplies provide redundancy either when used in pairs, or when
combined with an internal module.
Internal Power Supplies
Dataprobe offers the following internal supply modules for the RSS series:
1930084 100 – 240 VAC, 50-60 Hz
1930083 100 – 240 VAC, 50-60 Hz – Power Factor Corrected
1930086 42 – 60 VDC
1930081 24 VDC External Connection Panel, Dual Inputs
3.1. Power Supply 1930084
Converts 110/ 220 /240 VAC to 24VDC
Single Slot Redundant Capable
3.1.1. INPUT POWER
Nominal : 120/240 VAC 50/60 Hz
Range : 100 - 240 VAC
Watts: 50
Fusing: 2 A
3.1.2. ENVIRONMENTAL
Operating: 0 C -+ 50 C
3.1.3. PHYSICAL
Plug in rack card installs from rear of chassis
3.1.4. AC Input connector:
IEC 320 (C14) on rear panel
3.1.5. Alarm / Expansion connector:
9 pin d-Sub
Contact Ratings: 1A @ 24VDC res.

RSS_v180808n RSS Series Page 7
3.2. Power Supply 1930083
Converts 110/ 220 /240 VAC to 24VDC
Single Slot Redundant Capable
Power Factor Corrected
3.2.1. INPUT POWER
Nominal : 120/240 VAC 50/60 Hz
Range : 100 - 240 VAC
Watts: 50
Fusing: 2 A
3.2.2. ENVIRONMENTAL
Operating: 0 C -+ 50 C
3.2.3. PHYSICAL
Plug in rack card installs from rear of chassis
3.2.4. AC Input connector:
IEC 320 (C14) on rear panel
3.3. Power Supply 1930086
Converts 48 VDC to 24VDC
Single Slot Dual Redundant Capable
3.3.1. INPUT POWER
Nominal : 48 VDC
Range : 42 - 60 VDC
Watts: 75
Fusing: 2.5 A
Minimum Wire Rating: 14 AWG (1.63mm), 75 Deg C, 48VDC
Maximum DC Mains Branch Circuit Protection : 3.5 A
3.3.2. ENVIORMENTAL
Operating: 0 C -+50 C
3.3.3. PHYSICAL
Plug in rack card installs from rear of chassis
3.3.4. DC Input Connector:
Screw Terminal Mating Connector Supplied.

RSS_v180808n RSS Series Page 8
3.3.5. Alarm / Expansion connector:
9 pin d-Sub
Contact Ratings: 2.5 A @ 24VDC res.
3.3.6. Restricted Access Location
This power supply must be installed in restricted access areas such as dedicated equipment room, or electrical
closet, in accordance with United States National Electrical Code.
A RESTRICTED ACCESS LOCATION is a location for equipment where both of the following apply:
•Access can only be gained by service persons or by users who have been instructed about the reasons for
the restrictions applied to the location and about any precautions that shall be taken; and
•Access is through the use of a tool or lock and key, or other means of security, and is controlled by the
authority responsible for the location.
3.4. Power Supply Installation
Power Supplies insert into the chassis from the rear. An LED indicator on the front panel of the chassis displays
power supply operation. Insert the power supply card in chassis prior to applying power.
3.4.1. RSS-3
The RSS-3 chassis supports one internal power supply installed thru the rear of the chassis, or an external 24VDC
power supply can also be used by installing the 24 VDC External Connection Panel item 1930081.
Redundant power can be added by connecting an external power supply to the DC power connector provided on
the control card using Connector Kit item 1940164.
LED indicators on the chassis front panel display the operating status of PS1 or PS2. The PS2 indicator only
functions when an external power supply is added for redundancy.
3.4.2. RSS-16 Power Supply Options
The RSS-16 can be configured for redundant power by using internal or external power supplies. Two internal
power supply cards can be installed in the single slot power supply position in any combination of AC and DC
models. The various configurations are shown below.
Insert the card into the desired power supply position from the rear of the chassis. PS1 is the top position and PS2
is the bottom position
A blank power card panel is included with the chassis when only one of the redundant supplies is installed. This
panel should be kept for future use when two supply cards are installed should the need for removal of one of the
supplies become necessary.
3.4.3. RSS-3 Power Supply Options
The RSS-3 provides one power supply
bay any power supply. For redundant
power, add the external power supply
1930076. Connection to an external
power supply can be made via the
24VDC power input on control cards
IOC-3, IPC-1 or IPC-16, or the External
24VDC Connection Panel 1930081.

RSS_v180808n RSS Series Page 9
+
_
2
3
4
6
Rear View
Pin1 +24VDC
Pin5 - Return
3.5. 24VDC Power Connection
The RSS-3 can be powered from an external 24VDC supply, Dataprobe Item # 1930076, or other 24 VDC, 2.5 A
source using an RSS DC Power Connector Kit Item #1940164. Two power Inputs are provided for redundant
power capability. Wiring detail is shown below. Note: The two inputs are isolated but will appear as PS1 on the front
panel LED indicator and thru the Power Supply Status when using the IPC-16 control card. PS2 indicates the status
of an external power supply connected to the control or gang expansion card option.
3.5.1. EXTERNAL 24VDC POWER WIRING
3.5.2. 24VDC Wiring Requirements
Minimum Wire Rating: 14 AWG (1.63mm), 75 Deg C, 48VDC
Maximum DC Mains Branch Circuit Protection : 3.5 A
3.5.3. Restricted Access Location
Use of the 24VDC connections requires the system must be installed in restricted access areas such as dedicated
equipment room, or electrical closet, in accordance with the United States National Electrical Code.
A RESTRICTED ACCESS LOCATION is a location for equipment where both of the following apply:
•Access can only be gained by service persons or by users who have been instructed about the reasons for
the restrictions applied to the location and about any precautions that shall be taken; and
•Access is through the use of a tool or lock and key, or other means of security, and is controlled by the
authority responsible for the location.
3.5.4. Alarm Connector
Alarm Connection on internal power supply modules provides status information on the condition of the supply.
9 Pin D-Sub Wiring
Pin 6 NO Pin 6 shorts to Pin 7 when the Power Supply is Non-Operational
Pin 7 COM
Pin 8 NC Pin 8 shorts to Pin 7 when the Power Supply is Operational
RSS-PAM-R Power Supply #2:
Pin 3 NO Pin 3 shorts to Pin 4 when the Power Supply is Non-Operational
Pin 4 COM
Pin 5 NC Pin 5 shorts to Pin 4 when the Power Supply is Operational

RSS_v180808n RSS Series Page 10
4.IPC-16-R Control Card
Item # 1340065
Two Control Cards are available for use in the RSS systems; IPC-16-R and IPC-1-R , providing remote access
control through network in-band and serial out-of-band circuits.
IPC-16-R: Both Ethernet TCP/IP and Serial Connections, Individual and Gang AB card control
IPC-1-R: Ethernet TCP/IP, Gang Control Only,
WEB
Through a web browser interface, you can access the control card, obtain current status information and operate
the A/B Switches
SNMP
The system can be managed by SNMP through standard management software. Dataprobe provides a private
MIB.
Telnet– IPC-16-R Only
Through a telnet client, you can access the control card, obtain current status information and operate the A/B
Switches. This is also the method for setting configuration parameters of the card
TCP Messaging – IPC-16-R Only
A direct TCP messaging protocol is supported for direct computer control of the A/B switching system.
Serial –IPC-16-R Only
The serial port on the IPC-16-R provides direct terminal access or via modem. The A/B Cards are controlled either
by a menu selection or by command line strings (escape code sequences). Menu selections are ideal for easy
operator interface and the escape code sequences streamline automated control.
4.1. Dual Control Cards RSS-16
The RSS-16 chassis has two control card slots for supporting either; two IPC-16-R networks control cards, or one
IPC-16-R and either the IOC-16-R or IOC-1-R I/O access cards.
When two network cards are installed both cards must be configured the same except for individual IP addresses.
The user must also control network access to avoid any conflicts in control contention.
Each controller provides pulsed control signals to the A/B switch cards. The switch cards will be positioned
according to commands from the last network controller or I/O access card used.
When a IPC-16-R Network control card and either IOC I/O access card is used, any contact closure externally
provided thru the I/O access card will override the network control if the external contact is not momentary.

RSS_v180808n RSS Series Page 11
4.2. IPC-16-R Installation
The IPC-16-R Control Card installs from the rear of the chassis in one of the
two control card slots only. The slot are on the left (facing the rear), next to the
power supply. Two IPC-16-R cards can be installed for redundant remote
access. Note: It is recommended that any removal or insertion of a control card
be performed with power off to prevent possible unintentional switching of the
switch cards.
The card provides the following connections:
External Power Input. Connection for external power supply, singularly, or as
a supplement to an internal supply for dual redundant power. Mating
Connector kit # 1940164
Gang Expansion. RJ11 connection for connection to additional chassis for
large gang switching applications.
Serial Port. RS-232 port for out-of-band access to the IPC-16-R card.
Ethernet. Network connection; 10baseT - IPC-16-R,
4.3. Serial Port
The Serial Port on the control card is a 9 pin male connector, configured as a DTE. The following pins are used.
The following chart illustrates the pin out of the D9 connector and the connection required to an external modem
with a D25 pin out.
D9 Pin Abbreviation Full Name
Modem
D25 Pin
Pin 2
RD
Receive Data
Pin 3
Pin 3
TD
Transmit Data
Pin 2
Pin 5
SG
Signal Ground
Pin 7
Pin 9
RI
Ring Indicator
Pin 22
For connection directly to a terminal, a Null Modem cable is required.
IPC-16-R
D9 Pin
Terminal
D9 Pin
Pin 3
Pin 2
Pin 2
Pin 3
Pin 5
Pin 5

RSS_v180808n RSS Series Page 12
4.5. Command Line Interface
The IPC-16-R is managed by a Command Line Interface (CLI) system via Telnet or Serial Port. The CLI uses a
username password challenge for security.
4.5.1. Factory defaults System Chassis and RCU
Username admin
Password admin
4.6. Telnet
The system supports the Telnet communications protocol for management access. Optionally, the telnet server in
the IPC-16-Rcan be disabled with a CLI command.
Connect via Telnet client to the IP address of the IPC-16-R
4.6.1. Factory Defaults
•RSS IP Address 192.168.1.254
4.7. Serial Port
To login in to the IPC-16-Rusing the serial port, set the terminal to the baud rate and character format, then send a
Carriage Return <Enter key> .
Baud Rate Baud rate choices are 9600, 19200, 38400, 57600 and 115200 bits per second. Character format is
fixed at 8 Data Bits, No Parity, One Stop Bit. (8, N, 1)
4.7.1. Factory Defaults
•9600, 8 Data Bits, No Parity, One Stop Bit (9600,8,N,1)
4.8. SNMP
The IPC-16-R system is SNMP manageable. Up to four SNMP managers can be defined for the purpose of
delivering status Inform messages.
4.8.1. Factory Defaults
•Read Community: public
•Read/Write Community: private
•Notification Timeout: 1 second
•Notification Retry Count: 3
•Lead Configuration Change: 0 seconds
4.9. Command Line Interface
4.9.1. Initial connection
To establish a connection to the system chassis via the network, open a telnet client to the IP address of the
system. The session will begin upon connection.
To access the system chassis via the serial port, connect a suitable dumb terminal, or system running terminal
emulation to the serial port at the proper baud rate and character format. Send <Enter> via the serial port to begin
the session.

RSS_v180808n RSS Series Page 13
Upon Connection the system will send the Model, Version and login prompt:
Hello... connected to RSS-16!
Connected to Telnet Session 2
User>
Enter the username. The system will then prompt for a password:
Password>
Enter the password. If successful, the system will send the system level prompt:
RSS-16>
4.9.2. CLI Navigation
The system uses a tree structured navigation system. System level, indicated by the RSS-16> prompt set the or
display the basic parameters for the IPC-16-R including all network configuration. To access any card level
parameters, including the A/B status of the card, select the card with the select card command
RSS-16> select card 3
RSS-16.Card 3>
The prompt changes to indicate the current card selected. To return to the system level, send the exit command.
4.10. Configuration – IPC-16-R
Configuration of the IPC-16-R involves the following steps:
•Setting The IPC-16-R's IP Address
•Setting additional configuration parameters.
4.10.1. Setting I/P Address
The IPC-16-R comes with factory installed IP address 192.168.1.254. In most cases this will need to be changed.
Consult your Network Administrator to determine the appropriate IP address. There are several methods to change
the IP address.
•ARP
•Telnet
•Serial Port
•setip.exe program, available from Dataprobe’s web site
To set the IP address, the hardware (MAC) address must be known. This address is located on a label on on the
IPC-16-R printed circuit board. The syntax for the MAC address is: nn-nn-nn-nn-nn-nn
4.10.2. Setting the IP address using ARP
To set the IP address using ARP, connect the jack marked 10Base-T to your local Ethernet network and apply
power to the unit. The computer used to set the IP address must be on the same physical network as the IPC-16-
R. ARP does not work across switched or routed networks.
4.10.3. Windows (98 and Later)
1. Open a DOS window.

RSS_v180808n RSS Series Page 14
2. Type the following command:
arp -s <IP Address> <MAC Address>
Where <IP Address> is the desired IP address (in dotted decimal) for the IPC-16-R and the <MAC address> is
the MAC Address of the IPC-16-R. The MAC Address is located on a label on the rear panel of the card.
Example: arp -s 63.211.86.165 00-50-c2-05-01-c1 <enter>
|--- new IP addr. ---| |------- MAC addr. ------|
3. Ping the IPC-16-R to program the IP address into the IPC-16-R.
Type: ping <IP Address>
If the ping command returns “host not responding” 4 times then the address has not been programmed
properly, or the IP or MAC Address is incorrect. In either case redo step 2. If the problem persists, contact the
Dataprobe Tech Support Hot Line.
4. Delete the entry from the ARP cache by typing:
arp -d <IP Address>
5. Ping the IPC-16-R to confirm that it has been programmed.
If the card fails to respond, repeat steps 2-4 above. If the problem persists contact the Dataprobe support hotline.
4.10.4. Unix, Linux
Consult your systems administrator for information on setting an IP Address using ARP. The unit should be pinged
after the IP Address has been set to confirm proper operation.
4.10.5. Setting IP Address with Telnet
For initial setup, the computer used must use the same network segment as the default IP Address, or current IP
address. (192.168.1.xxx) If this is not the case, use one of the other methods. To connect to the IPC-16-R using
telnet, run your telnet client program (provided with your operating system) and connect to the IP address as set in
step one above.
For Windows: Select Run…Telnet
Connect…192.168.1.254 (or the current IP address)
As soon as you connect the following message will be displayed:
4.10.6. Setting IP address via Serial Port
The serial port uses the same menu sequences as the Telnet method described above. Connect a terminal directly
to the IPC-16-R serial port. Send an Enter keystroke to start the session. The serial port default settings are
9600bps, 8 data bits, no parity, one stop bit. These setting can also be changed via the menus.
4.10.7. Setting IP Address with setip.exe
Utility setip.exe is available from Dataprobe’s website at http://dataprobe.com/support/rss/setip.exe. Download this
windows program and run it on any computer on the same physical network segment as the control card. Enter the
MAC address and desired IP address and press SetIP.
4.11. Setting other Parameters
Via the Serial Port or telnet, all other configuration parameters can be set for the IPC-16-R. These setting are made
from the Command Line Interface, as described in the section 4.13 . Some specific settings to consider are:
Location Name: Enter a 1-20 character name to identify the system. This name appears at the top of each telnet
screen and web page.

RSS_v180808n RSS Series Page 15
Card Setup: This allows setting of parameters for individual A/B cards in the system. Each card can be named, up
to 20 characters, and can be enabled or disabled. Disabling a card hides its status from web and telnet screens.
This should be used where no card is installed, to make reading the screens easier.
Password: A password from 1 to 15 characters is needed for access to the system. Re-enter the old password
then enter the new password twice as prompted.
Com Port: Set the Baud Rate and Character Format for the serial port. Baud rate choices are 9600, 19200, and
38400. Character format choices are 8N1, 7E1 and 7O1 (databits, parity, stop bit).
The Default Serial Port Parameters are 9600, 8 Data Bits, No Parity, One Stop Bit (9600,8,N,1)
Escape Response: This selects Yes or No for escape code responses. See section 3.4.3 on escape code control
Web Port, Telnet Port, Message Port: These three settings determine the port assignment for the different TCP
protocols used to communicate with the control card. Standard port assignments for these protocols are:
WEB: 80
Telnet: 23
Message: 9100
If you change these assignments, you will need to specify them when you connect to the IPC-16-R. For example if
the IP address of the IPC-16-R is 192.168.1.254 and you have changed the web port to 8800, then you would need
the following URL to access the IPC-16-R: http://192.168.1.254:8800
Note: After changing the IP Address, Web Port, Telnet Port or Com Port parameters, it is necessary to reboot the
IPC-16-R Card. Do this by entering selection “System Reset”, item 6 in the System Setup Menu displayed in the CLI
during a Telnet session, or momentarily powering Off the power to the chassis power supply. Power cycling the
power source to the chassis power supply will insure no unintentional changes in switch positions of any A/B Card in
the chassis.
MTU: Maximum Transmission Unit. Set the MTU from 100 to 1024. The default of 1024 should not be changed
unless required by network architecture.
Read and Write Community Names: These settings are for use with SNMP managers only. Set the names as
appropriate for your SNMP configuration.
SNMP Managers: Set up to four SNMP managers that will receive SNMP TRAPs. Other SNMP managers will be
able to manage the system.
4.12. Operation
Remote control of each or all A/B Cards is accomplished using either TCP/IP protocols for Web browser (http) ,
Telnet, or direct TCP messaging. Each card in the chassis can be operated independently, or all 16 A/B cards can
be operated simultaneously. In all cases, switch control is password protected.

RSS_v180808n RSS Series Page 16
4.13. Command Line Interface
4.13.1. System Level Commands
Command
Description
Default
logout
Log out of the system
reboot
Reboot the system
get all
Get system status
RSS System: Network_Ops Power 1: Fail Power 2: Ok
Controller F/W: v1.00.067
ID Name Enabled Act
1 NewYork Yes A
2 Boston Yes A
3 Providence Yes A
4 Philadelphia Yes A
5 Baltimore Yes B
6 WDC_East Yes A
7 WDC_West Yes A
8 Atlanta Yes A
9 Miami Yes B
10 Seattle Yes A
11 Portland Yes B
12 San_Francisco Yes A
13 Phoenix Yes B
14 Houston No -
15 Chicago No -
16 Pittsburgh No -
Ok
RSS-16>
select card <1-16>
Moves to card level. Prompt changes to
RSS.Card nn>
get location
set location <0-20 characters>
Sets the displayed name of the chassis. 20 Characters maximum
Set Location

RSS_v180808n RSS Series Page 17
get powersupply
Get the current state of the power supplies
RSS-16> get powersupplies
Power Supply 1: Fail
Power Supply 2: Ok
Ok
RSS-16>
get upgrade enable
set upgrade enable <yes|no>
Set firmware upgrade enable flag
no
get mac
set mac <XX:XX:XX:XX:XX:XX>
Set network MAC address
get network
Get network IP settings
RSS-16> get network
IP Mode: Static
IP Address: 10.10.10.70
Subnet: 255.255.255.0
Gateway: 10.10.10.7
DNS1: 0.0.0.0
DNS2: 0.0.0.0
Ok
RSS-16>
set ipmode <static|dhcp>
Sets the IP Mode
Static: The IP address is set manually
DHCP: The IP Address is set by DHCP Server
static
set ipaddress <xxx.xxx.xxx.xxx>
Sets the IP Address in dotted decimal
192.168.1.254
set subnet <xxx.xxx.xxx.xxx>
Sets the subnet mask in dotted decimal
255.255.255.0
set gateway <xxx.xxx.xxx.xxx>
Sets the gateway in dotted decimal
0.0.0.0
set dns1 <xxx.xxx.xxx.xxx>
Set network DNS server 1 IP address
0.0.0.0
set dns2 <xxx.xxx.xxx.xxx>
Set network DNS server 2 IP address
0.0.0.0

RSS_v180808n RSS Series Page 18
get console
Displays the current console and telnet settings
RSS-16> get console
Auto Logout: 50 minute(s)
Serial Login: Yes
Baud Rate: 9600 BPS
Telnet Enabled: Yes
Telnet Port: 23
Ok
RSS-16>
set console timeout <0-99>
Set the current timeout (auto logout) value minutes (0=disable)
Default =
set console serial login <yes|no>
Set the serial login enable flag
set console serial baud
<2400|9600|57600|115200>
Sets the baud rate on the serial port.
Serial port character format is fixed at : 8 Data bits, No Parity, One Stop Bit, (8,N,1)
9600
set console telnet enable <yes|no>
Set the telnet enable flag
Default =
set console telnet port <1-65535>
Set the telnet port
23
get SNMP Get network SNMP settings
RSS-16> get snmp
Read Community: public
Write Community: private
Manager IP Address 1: 192.168.1.19
Manager IP Address 2: 192.168.4.19
Manager IP Address 3: 10.10.10.60
Manager IP Address 4: 0.0.0.0
Ok
RSS-16>
set snmp enable <yes|no>
Set network SNMP enable flag
set snmp readcommunity <0-20>
Sets the trap community name for the specified SNMP manager
public
set snmp writecommunity <0-20>
Sets the read/write community name for the specified SNMP manager
private
set snmp manageripaddress <1-4> <ip>
Sets up to four SNMP managers
get http
Get network HTTP (web) settings
RSS-16> get http
HTTP Server Enabled: Yes
HTTP Port: 80
HTTPS Port: 443
HTTP SSL Enabled: No
Ok
RSS-16>

RSS_v180808n RSS Series Page 19
set http enabled <yes|no>
Set Web Server Enabled or Disabled
yes
set http port <1-65535>
Set network HTTP port
80
set http httpsport <1-65535>
Set network HTTPS SSL port
443
set http usessl <yes|no>
Set if Web Encryption, HTTPS is required
no
get escape Get escape sequence settings
RSS-16> get escape
Escape Enabled: Yes
Escape Port: 9100
Ok
RSS-16>
set escape enabled <yes|no>
Set escape sequence enable flag
yes
set escape port <1-65535>
Set escape sequence port
9100
set gang <a|b>
Gang Switches all cards in system to A or B
set password <1-20>
Set system password
admin
set factory defaults
Set system to factory defaults

RSS_v180808n RSS Series Page 20
4.13.2. Card Level Commands 4.13.3.
Command
Description
Default
get all
Get card status and configuration
RSS-16.Card 1> get all
Current Card Values:
Card ID: 1
Card Name: NewYork
Enabled: Yes
Active Port: A
Ok
RSS-16.Card 1>
get name
set name <0-20 characters >
Set card name
????
get enabled
set enabled <yes|no>
Set card enabled flag
yes
set type <empty|dumb>
Set card type (empty means not populated)
dumb
set activeport <a|b>
Set active port status
a
exit
Exit back to main level