DATATEC KEYSIGHT E36150 Series User manual

USER GUIDE
Autoranging DC Power Supplies
E36150 Series
This manual provides operating instructions for the Keysight E36150 Series Autoranging DC Power Supplies.
Always refer to the English version for latest edition.
Ihr Ansprechpartner /
Your Partner:
dataTec AG
E-Mail: [email protected]
>>> www.datatec.eu
Premium Plus Distribution Partner

Notices 5
Copyright Notice 5
Manual Part Number 5
Edition 5
Published by 5
Warranty 5
Technology Licenses 5
U.S. Government Rights 6
Third Party Licenses 6
Waste Electrical and Electronic Equipment (WEEE) 6
Declarations of Conformity 6
Safety Information 7
Safety and Regulatory Information 8
Safety Considerations 8
Safety Symbols 11
Regulatory Markings 12
South Korean Class A EMC declaration: 12
Safety and EMC Requirements 12
Environmental Conditions 13
1 Getting Started 14
Product Introduction 15
Features at a Glance 15
Options 16
Front panel at a glance 17
Rear panel at a glance 18
Meter view 19
Data logger view 21
Scope view (Option E36150ADVU) 23
Dimension diagram 25
Setup the instrument 25
Prepare Instrument for Use 26
Initial inspection 26
Standard shipped items 26
Documentation and firmware revisions 26
Recommended calibration interval 26
Fuse Information 27
Programming Ranges 28
Installation 29
Connecting the power cord 29
Connecting the outputs 30
4-wire sense connection 36
Interface connections 39
Installing the optional GPIB interface 43
Rack mounting the instrument 45
Remote Interface Configuration 46
Keysight IOLibraries Suite 46
GPIB configuration 46
LAN configuration 47
Using sockets 51
More about IP addresses and dot notation 52
2 Keysight E36150 Series User's Guide

Remote Control 53
Web interface 53
Technical connection details 55
Use the Built-in Help System 56
View the help information for the front panel key 56
View the list of help topics 56
Firmware Update 58
License for Optional Features 59
Obtaining the License for Option E36150ADVU 59
Installing License for Option E36150ADVU 59
Front Panel Menu Reference 61
2 General Operating Information 62
Turning the Unit On 63
Using the front panel knobs 64
View the error log 65
Controlling the Outputs 66
Step 1 - Set the output voltage and current 66
Step 2 - Enable the output 67
Step 3 - View the output voltage and current 67
Constant voltage and constant current 67
Using the Protection Function 68
Protection function 68
Configuring protection 68
Clears and OVP and OCP Event 70
Specifying 2-Wire or 4-Wire Sense 71
Specifying the Current Measurement Range 72
Specifying the Turn-on Preference 72
Specifying the Voltage Slew Rate 73
Configuring the Output Turn On Turn Off Sequence 74
Step 1 – Set the output voltage and current 74
Step 2 – Configure the turn-on turn-off delays: 74
Step 3 – Coupling selected outputs: 74
Step 4 – Use the On key: 74
Generating Arbitrary Waveforms (Option E36150ADVU) 76
List Arb 77
Sine Arb (Option E36150ADVU) 82
Step Arb (Option E36150ADVU) 85
Ramp Arb (Option E36150ADVU) 87
Staircase Arb (Option E36150ADVU) 90
Pulse Arb (Option E36150ADVU) 93
Trapezoid Arb (Option E36150ADVU) 96
Exponential Arb (Option E36150ADVU) 99
Arb Sequence (Option E36150ADVU) 102
Using the Digital Control Port 107
Bi-directional digital IO 107
Digital input 109
Fault output 109
Inhibit input 110
Fault/inhibit system protection 111
Trigger input 112
Trigger output 113
Keysight E36150 Series User's Guide 3

Output couple controls 114
Using the Data Logger Function 116
Logging data 116
Step 1 – Program the sequence for the output channel 116
Step 2 – Configure the data logger traces 117
Step 3 – Configure the data logger properties 117
Step 4 – Turn on Output, start the sequencing and log the data 118
Step 5 – Export the data 118
Data logger view 120
Data logger marker view 121
Using the knob in data logger view 122
Data logger properties and waveform settings 123
Save the data log 127
Using the Scope Function (Option E36150ADVU) 130
Making measurement 130
Step 1 – Program the output voltage and current values 130
Step 2- Configure the output turn-on sequence 130
Step 3 - Configure the Scope View traces 131
Step 4 – Configure the Scope properties: 131
Step 5 – Turn on the outputs and measure the voltage: 131
From the remote interface: 132
Scope View 133
Scope marker view 135
Using the knob in scope view 136
Scope properties and waveform settings 137
Scope marker properties 140
Save the scope data 141
Locking/Unlocking the Front Panel 142
Capturing a Screen 142
Utilities Menu 143
Utilities Menu - Store and Recall State 143
Store Settings 144
Recall Settings 146
Power On Setting 147
Set to Defaults 147
Utilities Menu - I/O Configuration 148
LAN Settings 148
Digital IO 149
GPIB (optional) 149
Utilities Menu - Test / Setup 150
Calibration 150
Self-Test 151
User Settings 151
Help 153
Utilities Menu - Error 154
Utilities Menu - Manage Files 155
Action 155
Browse 156
File Name 156
3 Characteristics and Specifications 157
4 Service and Maintenance 158
4 Keysight E36150 Series User's Guide

Notices
Copyright Notice
© Keysight Technologies 2022
No part of this manual may be reproduced in any form or by any means (including electronic storage and retrieval or
translation into a foreign language) without prior agreement and written consent from Keysight Technologies as
governed by United States and international copyright laws.
Manual Part Number
E36151-90001
Edition
Edition 1, September 2022
Published by
Keysight Technologies
Bayan Lepas Free Industrial Zone
11900 Bayan Lepas, Penang
Malaysia
Warranty
THE MATERIAL CONTAINED IN THIS DOCUMENT IS PROVIDED “AS IS,” AND IS SUBJECT TO BEING CHANGED,
WITHOUT NOTICE, IN FUTURE EDITIONS. FURTHER, TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE
LAW, KEYSIGHT DISCLAIMS ALL WARRANTIES, EITHER EXPRESS OR IMPLIED, WITH REGARD TO THIS MANUAL
AND ANY INFORMATION CONTAINED HEREIN, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. KEYSIGHT SHALL NOT BE LIABLE FOR ERRORS
OR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES IN CONNECTION WITH THE FURNISHING, USE, OR
PERFORMANCE OF THIS DOCUMENT OR OF ANY INFORMATION CONTAINED HEREIN. SHOULD KEYSIGHT AND
THE USER HAVE A SEPARATE WRITTEN AGREEMENT WITH WARRANTY TERMS COVERING THE MATERIAL IN
THIS DOCUMENT THAT CONFLICT WITH THESE TERMS, THE WARRANTY TERMS IN THE SEPARATE AGREEMENT
SHALL CONTROL.
Technology Licenses
The hardware and/or software described in this document are furnished under a license and may be used or copied
only in accordance with the terms of such license.
Keysight E36150 Series User's Guide 5

U.S. Government Rights
The Software is “commercial computer software,” as defined by Federal Acquisition Regulation (“FAR”) 2.101.
Pursuant to FAR 12.212 and 27.405-3 and Department of Defense FAR Supplement (“DFARS”) 227.7202, the U.S.
government acquires commercial computer software under the same terms by which the software is customarily
provided to the public. Accordingly, Keysight provides the Software to U.S. government customers under its
standard commercial license, which is embodied in its End User License Agreement (EULA), a copy of which can be
found at http://www.keysight.com/find/sweula. The license set forth in the EULA represents the exclusive authority
by which the U.S. government may use, modify, distribute, or disclose the Software. The EULA and the license set
forth therein, does not require or permit, among other things, that Keysight: (1) Furnish technical information related
to commercial computer software or commercial computer software documentation that is not customarily provided
to the public; or (2) Relinquish to, or otherwise provide, the government rights in excess of these rights customarily
provided to the public to use, modify, reproduce, release, perform, display, or disclose commercial computer
software or commercial computer software documentation. No additional government requirements beyond those
set forth in the EULA shall apply, except to the extent that those terms, rights, or licenses are explicitly required from
all providers of commercial computer software pursuant to the FAR and the DFARS and are set forth specifically in
writing elsewhere in the EULA. Keysight shall be under no obligation to update, revise or otherwise modify the
Software. With respect to any technical data as defined by FAR 2.101, pursuant to FAR 12.211 and 27.404.2 and
DFARS 227.7102, the U.S. government acquires no greater than Limited Rights as defined in FAR 27.401 or DFAR
227.7103-5 (c), as applicable in any technical data.
Third Party Licenses
Portions of this software are licensed by third parties including open source terms and conditions. To the extent such
licenses require that Keysight make source code available, we will do so at no cost to you. For more information,
please contact Keysight support at https://www.keysight.com/find/assist.
Waste Electrical and Electronic Equipment (WEEE)
The crossed out wheeled bin symbol indicates that separate collection for waste electric and electronic equipment
(WEEE) is required, as obligated by the EU DIRECTIVE and other National legislation.
Please refer to keysight.com/go/takeback to understand your Trade in options with Keysight in addition to product
takeback instructions.
Declarations of Conformity
Declarations of Conformity for this product and for other Keysight products may be downloaded from the Web. Go
to https://regulations.about.keysight.com/DoC/default.htm. You can then search by product number to find the
latest Declaration of Conformity.
6 Keysight E36150 Series User's Guide

Safety Information
A CAUTION notice denotes a hazard. It calls attention to an operating procedure, practice, or the like that, if not correctly per-
formed or adhered to, could result in damage to the product or loss of important data. Do not proceed beyond a CAUTION notice
until the indicated conditions are fully understood and met.
A WARNING notice denotes a hazard. It calls attention to an operating procedure, practice, or the like that, if not correctly per-
formed or adhered to, could result in personal injury or death. Do not proceed beyond a WARNING notice until the indicated con-
ditions are fully understood and met.
Keysight E36150 Series User's Guide 7

Safety and Regulatory Information
Safety Considerations
The following general safety precautions must be observed during all phases of operation, service, and repair of this
instrument. Failure to comply with these precautions or with specific warnings elsewhere in this manual violates
safety standards of design, manufacture, and intended use of the instrument. Keysight Technologies assumes no
liability for the customer's failure to comply with these requirements.
BEFORE APPLYING POWER
– Verify that the correct fuse is installed. See Fuse Information for additional details.
– Ensure the mains supply voltage fluctuation do not exceed ±10% of the nominal supply voltage.
GROUND THE INSTRUMENT
This product is a Safety Class I instrument (provided with a protective earth terminal). To minimize shock hazard, the
instrument chassis and cover must be connected to an electrical ground. The instrument must be connected to the
AC power supply mains through a three-conductor power cable, with the third wire firmly connected to an electrical
ground (safety ground) at the power outlet. Any interruption of the protective (grounding) conductor or disconnection
of the protective earth terminal will cause a potential shock hazard that could result in personal injury. If the
instrument is to be energized via an external autotransformer for voltage reduction, be certain that the
autotransformer common terminal is connected to the neutral (earthed pole) of the AC power lines (supply mains).
DO NOT OPERATE IN AN EXPLOSIVE ATMOSPHERE OR WET ENVIRONMENTS
Do not operate the device around flammable gases or fumes, vapor, or wet environments.
DO NOT OPERATE DAMAGED OR DEFECTIVE INSTRUMENTS
Instruments that appear damaged or defective should be made inoperative and secured against unintended operation
until they can be repaired by qualified service personnel.
DO NOT SUBSTITUTE PARTS OR MODIFY INSTRUMENT
Because of the danger of introducing additional hazards, do not install substitute parts or perform any unauthorized
modification to the instrument. Return the instrument to a Keysight Technologies Sales and Service Office for service
and repair to ensure that safety features are maintained. To contact Keysight for sales and technical support, refer to
the support links on the following Keysight website: www.keysight.com/find/assist (worldwide contact
information for repair and service).
USE THE POWER CORD PROVIDED
Use the device with the power cord provided with the shipment.
USE THE DEVICE AS SPECIFIED
If the device is used in a manner not specified by manufacturer, the device protection may be impaired.
DO NOT BLOCK VENTILATION HOLES
Do not block the rear ventilation hole and keep at least 130 mm free space from the rear panel.
OBSERVE ALL DEVICE MARKINGS BEFORE CONNECTING TO DEVICE
Observe all markings on the device before connecting any wiring to the device.
TURN DEVICE OFF BEFORE CONNECTING TO OUTPUT TERMINALS
Turn off the device power before connecting to the output terminals.
8 Keysight E36150 Series User's Guide

ENSURETHEDETACHABLE FRONT PANELBINDINGPOST IS FIRMLYSCREWED
Ensure the detachable front panel binding post is firmly screwed to the output terminal. This binding post comes
together with the instrument and is connected to the output terminal.
DONOT REMOVE REAR OUTPUT TERMINALCOVER
- Do not remove the rear output terminal cover as it acts as safety cover to the output terminal.
- Output terminal connection must be performed with the presence of the output terminal cover.
ENSURE COVER IS SECURED IN PLACE
Do not operate the device with the cover removed or loosened.
TURN DEVICE OFF ANDREMOVEALL CONNECTIONS BEFORE INSTALLING THEGPIB INTERFACE
Turn off the power and remove all connections, including the power cord, from the instrument prior installation of the
GPIB interface.
ENSURE PROPER AWG CABLE IS USED
Use a cable with the correct voltage and AWG rating based on the intended setup when operating the E36150 Series
autoranging DC power supplies.
DO NOT TOUCH CABLES DURING OPERATION
Do not touch the cable while the instrument output is operational to prevent electric shock hazard and burn hazard.
DO NOT CONNECT FRONT AND REAR OUTPUT TERMINAL CONCURRENTLY
Do not connect the front and rear output terminal concurrently for the same output channel. Failing to observe the
connection requirement could potentially raise a fire hazard if the output current exceeding 80 A.
LETHAL VOLTAGES ANDCURRENTS
- SHOCK HAZARD. Floating voltage must not exceed 240 VDC. The total voltage on the output terminal and the
floating voltage must not be more than 240 VDC from chassis ground.
- The output terminal is designed for DC application. Ensure that transient voltages do not exceed 90 VPK.
- The connector screw terminals will be at hazardous potential when in operation.
- Personal injury on contact may result if these terminals are touched when equipment is in operation.
- To avoid injuries, always disconnect power, discharge circuits, and remove external voltage sources before any
installation.
- Installation procedures must be performed by a qualified and trained personnel on this equipment.
CLEANING
To prevent electric shock, unplug the unit before cleaning.
COIN BATTERY REPLACEMENT
- Be sure to use battery (KPN 1420-0942) for the coin battery replacement.
- Incorrect battery type and battery polarity used during the battery replacement can cause damage to the
instrument.
- Refer to E36150 Service Guide for coin battery replacement procedures. Battery replacement must be made only by
qualified service personnel.
Keysight E36150 Series User's Guide 9

CLEAN WITH DRY CLOTH
Clean the outside of the instrument with a soft, lint-free, dry cloth. Do not use detergent, volatile liquids, or chemical
solvents.
10 Keysight E36150 Series User's Guide

Safety Symbols
Symbol Description
Caution, risk of danger (refer to the manual for specific Warning or Caution information)
Caution, risk of electric shock
Protective earth (ground) terminal.
Earth ground
Frame or chassis (ground) terminal.
Standby supply. The instrument is not completely disconnected from AC mains when switch is off.
Alternating current (AC).
Plus, positive polarity.
Minus, negative polarity.
The WARNING sign denotes a hazard. It calls attention to a procedure, practice, or the like, which, if not correctly performed
or adhered to, could result in personal injury or death. Do not proceed beyond a WARNING sign until the indicated
conditions are fully understood and met.
The CAUTION sign denotes a hazard. It calls attention to an operating procedure, or the like, which, if not correctly
performed or adhered to, could result in damage to the product or loss of important data. Do not proceed beyond CAUTION
sign until the indicated conditions are fully understood and met.
The NOTE sign denotes important information. It calls attention to a procedure, practice, condition or the like, which is
essential to highlight.
Keysight E36150 Series User's Guide 11

Regulatory Markings
Symbol Description
The RCM mark is a registered trademark of the Australian Communications and Media Authority.
The CE mark is a registered trademark of the European Community. This CE mark shows that the product
complies with all the relevant European Legal Directives.
CAN ICES/NMB-001(A) indicates that this ISM device complies with the Canadian ICES-001.
Cet appareil ISM est conforme a la norme NMB-001 du Canada.
ISM GRP 1-A indicates that this is an Industrial Scientific and Medical Group 1 Class A product.
The UKCA (UK Conformity Assessed) marking is a UK product marking that is used for goods being placed on
the market in Great Britain (England, Wales, and Scotland)
This symbol indicates the time period during which no hazardous or toxic substance elements are expected to
leak or deteriorate during normal use. Forty years is the expected useful life of the product.
This symbol is a South Korean Class A EMC Declaration. This is a Class A instrument suitable for professional
use and in electromagnetic environment outside of the home.
The CSA mark is a registered trademark of the Canadian Standards Association.
South Korean Class A EMC declaration:
Information to the user:
This equipment has been conformity assessed for use in business environments. In a residential environment this
equipment may cause radio interference.
– This EMC statement applies to the equipment only for use in business environment.
사용자안내문
이 기기는 업무용 환경에서 사용할 목적으로 적합성평가를 받은 기기로서
가정용 환경에서 사용하는 경우 전파간섭의 우려가 있습니다.
–사용자 안내문은 “업무용 방송통신기자재”에만 적용한다.
Safety and EMC Requirements
This power supply is designed to comply with the following safety and EMC (Electromagnetic Compatibility) require-
ments:
- Low Voltage Directive
- EMC Directive
12 Keysight E36150 Series User's Guide

Environmental Conditions
The E36150 Series is designed for indoor use and in an area with low condensation. The table below shows the
general environmental requirements for this instrument.
Environmental condition Requirement
Temperature Operating condition: 0 °C to 40 °C
Storage condition: –20 °C to 70 °C
Humidity Operating condition: Up to 80% RH at 40 °C (non-condensing)
Storage condition: Up to 90% RH at 65 °C (non-condensing)
Altitude Up to 2000 m
Pollution degree 2
Installation category II (for AC input)
Mains voltage (rms) 100, 115, or 230 V input (±10%)
Mains frequency 50/60 Hz
Keysight E36150 Series User's Guide 13

1 Getting Started
Product Introduction
Prepare Instrument for Use
Fuse Information
Programming Ranges
Installation
Remote Interface Configuration
Remote Control
Using the Built-in Help System
Firmware Update
License for Optional Features
Front Panel Menu Reference
This chapter gets you started with the E36150 Series autoranging DC
power supplies.
14 Keysight E36150 Series User's Guide

Product Introduction
Features at a glance
Options
Front panel at a glance
Rear panel at a glance
Meter view
Data logger view
Scope view (Option E36150ADVU)
Dimension diagram
Setup the instrument
Features at a Glance
The Keysight E36150 Series Autoranging DC Bench Power Supply consists of the following models:
–E36154A Autoranging DC Power Supply 30 V, 80 A, 800 W
–E36155A Autoranging DC Power Supply 60 V, 40 A, 800 W
All models include:
Plenty of usable power
–Autoranging
–Peak power handling up to 3X maximum power rating
Safe, clean and reliable power
–Low output ripple and noise
–Excellent line/load regulation
–2-wire or 4-wire remote sense
–Detachable high current front binding post
–Over voltage, over current, and over temperature protection
Convenient benchtop capabilities and intuitive interfaces
–Thermal-control fan speed for minimal acoustic noise
–4-wire front output terminal - with sense and ground connection
–4.3-inch LCD color display
–Individual knobs for voltage and current
–LAN/LXI, USB, and GPIB (optional) interfaces
Keysight E36150 Series User's Guide 15

Advanced characterization
–Built-in voltage and current measurements
–Data logging
–Output sequencing and syncing with digital I/O
–LIST mode programming
–Low range current measurement
–Adjustable voltage slew rate
–Scope view (optional)
–Arbitrary (Arb) waveform generator (optional)
Application Software and Automation
–BV0003B Pathwave BenchVue Power Supply
–BV9201B Pathwave BenchVue Advanced Power Control and Analysis (optional)
Options
Options 0EM, 0E3, and 0E9 determine which power-line voltage is selected at the factory.
Ensure you order the proper instrument option for the mains power that will be used for the instrument.
Options Description
0EM 115 VAC ± 10%, 50/60 Hz input voltage
0E3 230 VAC ± 10%, 50/60 Hz input voltage
0E9 100 VAC ± 10%, 50/60 Hz input voltage
SEC NISPOM and file security
UK6 Commercial calibration with test results data
1A7 ISO 17025 calibration certificate with uncertainty
Upgradable options (available post-purchase)
Options Description
E363GPBU GPIB user installable interface module.
E36150ADVU Advance features of scope view and AWG capabilities
16 Keysight E36150 Series User's Guide

Front panel at a glance
Item Description
1 Information-packed, high contrast 4.3-inch LCD color display; easily viewable even from sharp angles
2 Voltage and Current knobs
Set the output voltage and current. These knobs are active in Meter View, Scope View, Data Logger View, and Source Settings page.
3 Meter View, List Run/Stop, and Scope/Datalog keys
–[Meter View] turns on the meter view
–[List Run/Stop] runs or stops the Arb. This key is equivalent to Arb Run/Stop key as described in the manual.
–[Scope/Datalog] toggles between Scope view and Data Logger view.
4 Navigation keys.
– Navigate through the control dialog windows; press [Enter] key to select a control.
5 Numeric keypad
– Enters numeric values. Press [Enter] key to complete the entry.
– Deletes the values entered into the dialog using the back key.
6 Output On key
Turns the output On or Off; output is on when the key is lit.
7 Output terminals
8 On/Standby key and LED indicator
Turns on the instrument. If the LED is amber, the instrument is in standby mode with AC inlet power connected, and if it is green, the
instrument is on.
9 Sense terminals
10 Earth ground reference
11 Softkeys
Accesses the soft front panel menu.
12 USB port
Allows an external USB drive to be connected to the instrument.
NOTE: The USB cable is not recommended to be longer than 3 meters.
Keysight E36150 Series User's Guide 17

Rear panel at a glance
Item Description
1 AC inlet
2 AC fuse-holder assembly
3 USB port
4 LAN port
5 Digital I/O terminal port
6 GPIB port (Option E363GPBU only)
7 Fan ventilation hole
8 Sense terminals
9 Kensington security slot
10 Earth ground reference
11 Output terminals
NOTE: When you received the unit, the rear output terminal is covered with safety
cover as illustrated below.
18 Keysight E36150 Series User's Guide

Meter view
The power supply's front panel features a high contrast 4.3-inch LCD color display. Press [Meter View].
Item Description
1 Remote sense status
2wire or 4wire indicates that 2-wire or 4-wire sensing measurement is in use.
2 Preferred mode status
Volt or Curr indicates the preferred mode for output on or output off transitions.
3 Current range indicator
Displays the current range indicator. This indicator will only show when low current range is selected.
4 Output status
OFF: The output is off
CV: The output is in constant voltage mode
CC: The output is in constant current mode
CCN: The output is limited by negative constant current.
UR: The output is unregulated
OV: Over-voltage protection is tripped
OC: Over-current protection is tripped
OT: Over-temperature protection is tripped
+IPK: The output is protected by positive peak current
-IPK: The output is protected by negative peak current
5 Instrument/Interface status
: The instrument is connected to USB.
: The instrument is connected to LAN.
(blinking): The instrument is under identification mode via
remote interface.
: The instrument is not connected to LAN.
(blinking): The LAN connection is at fault.
ARB: Arb is running.
!ERR: An error has occurred (press Utilities >Error to view the
Error Log).
6 Ratings and protection
Displays the present over-voltage protection (OVP) setting.
7 Output delay
Displays the OCP, Output On, and Output Off delay status/values.
8 Voltage slew
Displays the rising slew and falling voltage slew rate.
9 Soft front panel menu
Keysight E36150 Series User's Guide 19

Item Description
10 Output settings
Displays the present output voltage and current settings. Use the numeric keypad or turn the front panel voltage or current knob to
adjust these settings.
11 Output meters
Displays the actual output voltage and current. Displays power in single output view.
20 Keysight E36150 Series User's Guide