DaVinci Maestro Collection Square User manual

Maestro
Owner’s Manual
WARNING:
If the information in these instructions is not followed exactly, a fire or explosion may
result causing property damage, personal injury or loss of life.
- Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or
any other appliance.
- WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electrical switch; do not use any phone in your building.
• Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's
instructions.
• If you cannot reach your gas supplier, call the fire department.
- Installation and service must be performed by a qualified installer, service agency or the gas supplier.
Tested and Listed by
Report # 0028GF103S
ANSI Z21.50b-2014 /
CSA 2.22b-2014
Gas-Fired Domestic and Commercial Heating
Equipment “Vented Gas Fireplace”
This appliance may be installed in an aftermarket, permanently located, manufactured home
(USA only) or mobile home, where not prohibited by local codes.
This appliance is only for use with the type of gas indicated on the rating plate. This
appliance is not convertible for use with other gases, unless a certified kit is used.
INSTALLER: Leave this manual with the appliance.
CONSUMER: Retain this manual for future reference.
Travis Industries, Inc. 12521 Harbour Reach Dr., Mukilteo, WA 98275 www.travisproducts.com
Copyright 2017, T.I. $10.00 9/25/17 100-01468

2 Introduction
© Travis Industries 9/25/17-1384 DV/Maestro-Cat1
Overview
This manual details the Maestro fireplace.
Listing Details
This appliance was listed by Omni-Test
Laboratories, Inc. to ANSI Z21.50b-2014 / CSA
2.22b-2014. The listing label is chained to the
appliance near the glass frame. A copy is shown to
the right.
Massachusetts Approval
This manual has been submitted to the
Massachusetts Board of State Examiners of
Plumbers and Gas Fitters
National Fireplace Institute
Dealer Information
Please record your dealer information here for
future reference:
Dealer Name: ____________________
Dealer Address: ____________________
Dealer E-Mail: ____________________
Dealer Phone #: ____________________

Table of Contents 3
© Travis Industries 9/25/17-1468 Maestro
Overview.............................................................................2
Listing Details......................................................................2
Installation Options .............................................................6
BTU Specifications.............................................................. 6
Decimal Conversions..........................................................6
Dimensions – 3’ Single Sided.............................................7
Packing List......................................................................... 8
Recommended Installation Procedure................................9
Recommended Specialty Tools .......................................... 9
Massachusetts Requirements.............................................10
Requirements for the Commonwealth of Massachusetts10
MANUFACTURER REQUIREMENTS............................10
Alignment Track Installation................................................11
Secure the Fireplace to the Alignment Track......................12
Fireplace Placement Requirements....................................12
Clearances......................................................................12
Raised Fireplaces........................................................... 12
Typical Framing Dims. – One Sided Configuration.............13
Minimum Framing Dimensions .......................................13
Typical Framing Dims. – See Through Configuration.........14
Minimum Framing Dimensions .......................................14
Nailing Brackets..................................................................15
Accessing Internal Components.........................................16
Internal Shut Off Valve Access.......................................16
Burner Removal.............................................................. 17
Gas Line Requirements......................................................19
Fuel.................................................................................19
Gas Line Connection ......................................................19
Gas Inlet Pressure..........................................................19
Directions for Connecting a Gas Pressure Test Gauge..19
Gas Inlet Location........................................................... 20
Electrical Junction Box........................................................21
Junction Box Configuration............................................. 21
Electrical Input Connection.................................................22
Connecting the Power Vent Lead to the Fireplace .............23
Connecting the Intake Damper Harness to the Fireplace...24
Wiring the Intake Damper...................................................25
Connecting the Exhaust Damper Harness to the Fireplace 26
Wiring the Power Vent........................................................27
Wiring the Power Vent (continued).....................................28
Connecting the CAT5 Harness to the Fireplace .................29
Installing the TouchSmart Controller...................................30
TouchSmart Mounting Box .................................................31
Air Intake Requirements .....................................................33
Air Intake Ducts............................................................... 33
Intake Dampers...............................................................34
Air intakes in Warm Environments..................................34
Air intake Installation – Hood Versions (includes external
dampers)............................................................................. 35
Part Numbers..................................................................35
Installation Diagram (intake with damper)....................... 35
Installation.......................................................................35
Air Intake Dampers (for Hori. or Vert. Termination)............ 36
Vent Requirements.............................................................37
Vent Clearances ............................................................. 37
Altitude Considerations...................................................37
Approved Vent................................................................37
Vent Installation ..............................................................37
Approved Vent Configurations............................................38
Rheostat Adjustment....................................................... 39
Restrictor Adjustment...................................................... 39
Termination Requirements.............................................. 40
Power Vent – Dimensions, Framing, Mounting...................41
Exterior Power Vent Dimensions – Low Volume (RS12)
94400903........................................................................41
Exterior Power Vent Dimensions – High Volume (RS16)
94400904.........................................................................42
Framing - Exterior Power Vent (94400903 & 94400904 only)
.........................................................................................43
Mounting - Exterior Power Vent (94400903 & 94400904
only).................................................................................44
Interior Power Vent – Dimensions and Mounting................45
Interior Power Vent Dimensions – (Lo 160) 94400905 ...45
Interior Power Vent Dimensions – Inline Version (Hi 180)
94400906.........................................................................45
Interior Power Vent - Typical Installation Arrangements .45
Interior Power Vent - Minimum Vent Pre and Post Blower 46
Interior Power Vent – Mounting.......................................46
Interior Power Vent Enclosure.........................................47
Interior Power Vent - Attaching Vent to the Blower Assembly
.........................................................................................47
Interior Power Vent - Components..................................47
Hearth Requirements ..........................................................49
Facing Requirements ..........................................................48
Do Not Drill or Screw Zone..............................................49
Mantel Requirements ..........................................................49
Fireback Installation.............................................................50
Fireback Quantity Needed – Category 1 Fireplaces .......50
Fireback Installation Order ..............................................50
Installing the Divider and End Firebacks.........................52
Glass Pane Installation and Removal..................................53
Suction Cups...................................................................53
When to Install the Glass Panes .....................................53
Maestro - Overview of Glass Panes – Category 1 Fireplaces
.........................................................................................53
Attaching the Suction Cups to the Glass Panes..............54
Installing the Glass Panes Into the Fireplace..................55
Steps for Finalizing the Installation......................................56
Air Shutter Adjustment.....................................................57
Crushed Glass Installation...................................................58
Placing Crushed Glass on the Burner and Center Media
Trays................................................................................58
Wiring Diagram....................................................................59
Before You Begin ................................................................60
Starting the Heater for the First Time..................................60
Location of Controls.............................................................61
LED Intensity Slider.........................................................61
LED Color Slider..............................................................61
Flame On/Off...................................................................61
Overhead Light................................................................61
Sleep Timer Slider...........................................................61
Yearly Service Procedure....................................................62
Glass Cleaning....................................................................62
Replacement Parts..............................................................62
CONDITIONS & EXCLUSIONS ..........................................63
IF WARRANTY SERVICE IS NEEDED:..............................63

4 Safety Precautions
© Travis Industries 9/25/17-1468 Maestro
Safety Warnings:
Failure to follow all of the requirements may result in property damage, bodily injury, or even death.
Young children should be carefully supervised when they are in the same room
as the appliance. Toddlers, young children and others may be susceptible to
accidental contact burns. A physical barrier is recommended if there are at-risk
individuals in the house. To restrict access to a fireplace or stove, install an
adjustable safety gate to keep toddlers, young children and other at-risk
individuals out of the room and away from hot surfaces.
Children and adults should be alerted to the hazards of high surface temperature
and should stay away to avoid burns or clothing ignition. Do not touch the hot
surfaces of the heater. Educate all children of the danger of a high-temperature
heater.
Due to the high temperature, the heater should be located out of traffic and away
from furniture and draperies.
This unit must be installed by a qualified installer to prevent the possibility of an explosion.
This appliance must be installed in accordance with all local codes, if any; if not, in U.S.A. follow ANSI
Z223.1 and NFPA 54(88), in Canada follow CSA B149.1.
A manufactured home (USA only) or mobile home OEM installation must conform with the
Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280, or, when such a
standard is not applicable, the Standard for Manufactured Home Installations, ANSI/NCSBCS
A225.1, or Standard for Gas Equipped Recreational Vehicles and Mobile Housing, CSA Z240.4. This
appliance may be installed in Manufactured Housing only after the home is site located.
All exhaust gases must be vented outside the structure of the living-area. Combustion air is drawn
from outside the living-area structure. The venting must not be connected to a chimney flue serving a
separate solid-fuel burning appliance.
Notify your insurance company before hooking up this fireplace.
The instructions in this manual must be strictly adhered to. Do not use makeshift methods or
compromise in the installation. Improper installation will void the warranty and safety listing.
This heater is approved for use with natural gas (NG) or propane (LP). Burning the incorrect fuel will
void the warranty and safety listing and may cause an extreme safety hazard. Direct questions about
the type of fuel used to your dealer.
Contact your local building officials to obtain a permit and information on any installation restrictions
or inspection requirements in your area.
If the flame becomes sooty, dark orange in color, or extremely tall, do not operate the heater. Call
your dealer and arrange for proper servicing.
It is imperative that control compartments, screens, or circulating air passageways of the heater be
kept clean and free of obstructions. These areas provide the air necessary for safe operation.
Do not operate the heater if it is not operating properly in any fashion or if you are uncertain. Call
your dealer for a full explanation of your heater and what to expect.
Do not store or use gasoline or other flammable liquids in the vicinity of this heater.
Do not operate if any portion of the heater was submerged in water or if any corrosion occurs.
Immediately call a qualified service technician to inspect the appliance and to replace any part of the
control system and any gas control which has been under water.

Safety Precautions 5
© Travis Industries 9/25/17-1468 Maestro
Safety Warnings (continued)
Because this heater can be controlled by a thermostat there is a possibility of the heater turning on
and igniting any items placed on or near the appliance.
Light the heater using the built-in igniter. Do not use matches or any other external device to light
your heater.
Never remove, replace, modify or substitute any part of the heater unless instructions are given in this
manual. All other work must be done by a trained technician. Don't modify or replace orifices.
The viewing glass should be opened only for conducting service.
Allow the heater to cool before carrying out any maintenance or cleaning.
Operate the heater according to the instructions included in this manual.
If the main burners do not start correctly turn the gas off and call your dealer for service.
This unit is not for use with solid fuel.
Do not place anything inside the firebox (except the optional artwork).
Warning: Do not operate appliance with the glass front removed, cracked or broken. Replacement
of the glass should be done by a licensed or qualified service person.
Do not throw this manual away. This manual has important operating and maintenance instructions
that you will need at a later time. Always follow the instructions in this manual.
Instruct everyone in the house how to shut gas off to the appliance and at the gas main shutoff valve.
The gas main shutoff valve is usually next to the gas meter or propane tank and requires a wrench to
shut off.
Clothing or other flammable material should not be placed on or near the appliance.
Any safety screen, guard, or barrier removed for servicing an appliance must be replaced prior to
operating the appliance.
Installation and repair should be done by a qualified service person. The appliance should be
inspected before use and at least annually by a professional service person. More frequent cleaning
might be required due to excessive lint from carpeting, bedding material, et cetera. It is imperative
that control compartments, burners, and circulating air passageways of the appliance be kept clean.
Travis Industries, Inc. grants no warranty, implied or stated, for the installation or
maintenance of your heater, and assumes no responsibility of any consequential damage(s).
Proposition 65 Warning: Fuels used in gas, woodburning or oil fired appliances, and the products of combustion of such
fuels, contain chemicals known to the State of California to cause cancer, birth defects and other reproductive harm.
California Health & Safety Code Sec. 25249.6

6 Features and Specifications
© Travis Industries 9/25/17-1468 Maestro
Installation Options
Residential or Commercial Installations
Raised or Floor Placement
Internal or External Chase

Horizontal or Vertical Vent
Bedroom Approved
Important Notes Regarding Installation Approvals
We strongly suggest consulting with the local building official on all aspects of this fireplace
(including the intake and exhaust configuration) prior to installation. Each locality and
installation type (residential, commercial, etc…) may have specific installation requirements
that are not covered in this manual (e.g. Int. Fuel Gas Code, section 503, etc.).
BTU Specifications
Maestro NG LP
3’x3’ – BTU Input Per Hour 43,500 43,500
3’x4’ – BTU Input Per Hour 70,000 70,000
4’x4’ – BTU Input Per Hour 70,000 70,000
3’x58” – BTU Input Per Hour 70,000 70,000
Decimal Conversions
0.125” 1/8”
0.25” 1/4"
0.375” 3/8”
0.5” 1/2"
0.625” 5/8”
0.75” 3/4"
0.875” 7/8”

Features and Specifications 7
© Travis Industries 9/25/17-1468 Maestro
Dimensions – 3’ Single Sided
(a) Air intake 8” Dia (left or right)
(b) Vent Collar (10” or 8”)
(c) Gas Control Valve – Located to the front of the fireplace (front of fireplace is determined by gas control valve location).
(d) Electrical Junction Boxes – (location determined at time of order – can be relocated) includes low & high voltage connections.
(e) Gas Inlet – Location is determined at time of order (can be relocated)
(f) Vent Collar Distance to Front/Back – Approx. 4-3/8” (112mm) for 10” B-Vent, 5-3/8” (137mm) for 8” B-Vent
NOTE: When using a 2-sided fireplace, the front is determined by the gas control valve (it is to the front).
Important Notes Regarding Framing
We strongly suggest framing around the fireplace after it is in place. If you do frame before
fireplace placement, add 6” to each side (12” total) to allow for fireplace assembly.
38" 966mm
b

d
a
e
f
Front
avant
Right
droit
Rear
arrie're
Left
a' gauche
36" (915mm)
48" (1220mm)
58" (1474mm)
Glass
Opening
36" (915mm)
e
d
c
Side of
Fireplace
19-3/4"
502mm
43-1/2" 1105mm
3/4"
19mm
Top of Fireplace
7"
(178mm)
36" Glass
66-5/8 (1693mm)
48" Glass
78-5/8" (1998mm)
58" Glass
88-5/8" (2252mm)
36" Glass
43-1/2"
1105mm
48" Glass
55-1/2"
1410mm
58" Glass
65-1/2"
1664mm
8-3/4"
223mm

8 Installation (for qualified installers only)
© Travis Industries 9/25/17-1468 Maestro
Packing List
Included Hardware (for Set & Vent)
ITEM Qty Location Notes
Manual 1 You’re looking at it baby!
CAT5+ cable 1 Hardware Box 25ft, 50ft or 100ft Length
TouchSmart Mounting
Plate 1 Hardware Box
Mounting Plate Box –
New Construction 1 Hardware Box
Mounting Plate
Backplate - Retrofit 1 Hardware Box
TouchSmart controller 1 Hardware Box
TouchSmart Hardware
pk. 1 Hardware Box - (6) Lock Ties (for wiring)
- (3) Round magnets w/ felt
pads
- (2) #8 Self-Drilling Screws
- (2) 8-32 x 1.5” Screws (for
Mtg Plate)
Exhaust Blower
Assembly 1 On its own pallet
Additional Equipment Required (for Set & Vent)
ITEM REQUIRED WHERE SHIPPED SKU
Suction Cups For Glass Yes Ordered separately 94400914 (includes 2 suction cups)
Fireback Liners (see
“Firebacks” on page 50) Yes In its own box or with the glass.
Exhaust Damper Wiring
Harness Yes Hardware Box 50 Foot 94700887
150 Foot 94700888
250 Foot 94700889
10” or 8” B-Vent Yes In its own box(s)
Recommended Intake
Damper(s) (A) Hardware Box
Hori w Term 8” (98900094)
Inline Dmpr 8” (98900079)
Air Intake (8” Dia.) (A)
Intake Wiring Harness (A) Hardware Box 25’ Length (Black and White Wire)
Finalization Hardware (install after fireplace is in place – you may hold at dealership)
ITEM Location Notes
Crushed Glass Hardware Box Center Channel uses 1.5 Lbs.
(cups) per foot
Outer Channel uses 1 Lbs.
(cups) per foot
Glass Panes In its own Crate/Pallet Pallet is strapped to fireplace

Installation (for qualified installers only) 9
© Travis Industries 9/25/17-1468 Maestro
Recommended Installation Procedure
Important Notes Regarding Framing
We strongly suggest framing around the fireplace after it is in place. Because this fireplace can be
very large, and difficult to position, you will need to make accommodations with the framing to allow for
placement. For one-sided, see-through, bay, or side configurations,you may wish to leave one or both
sides of the framing open to allow for fireplace placement and hookup. If framing the opening prior to
fireplace placement, you will also wish to make the framing 6” (150mm) wider on each framed side (12” /
300mm wider for singled sided/see through configurations). This allows for fireplace access and will be
covered with drywall (or other material) after the fireplace is assembled.
The header above the fireplace is best installed after the fireplace is in position and the vent attached.
The fireplace must be lifted onto the alignment track, so additional space above the fireplace is requried
for lifting and placement.
1. Prepare the installation location. If placing the fireplace on a platform, build the platform, making sure
to accommodate the weight of the fireplace and venting. Verify the platform is level and plumb.
2. Install the alignment track (if used - see page 11).
NOTE: The alignment track is optional. We recommend using the track because it helps solidify the
base of the fireplace and it allows the fireplace to be anchored at the base.
3. Place the fireplace eon the alignment track and verify it is level and aligned correctly.
4. Install the periphery components:
a) Install the vent (and power vent blower assembly).
b) Install the air intake(s).
c) Install the gas line.
d) Install the electrical line and TouchSmart controller.
5. Test operation of the fireplace before attaching facing or drywall (this can be done with no crushed
glass and the outer glass pane(s) removed). This allows the installer to verify all connections and
diagnose issues with the fireplace exterior accessible.
a) Adjust the air shutters (if needed)
b) Adjust the exhaust blower (if needed)
c) Shut the fireplace off. Install the outer the glass pane(s).
d) Re-start the fireplace and test glass pane temperature (allow fireplace to burn 2 hours)
6. Frame the area around the fireplace.
7. Install the drywall and/or facing.
8. Install the hearth (if applicable). Install the mantel (if applicable).
9. Finalize the installation (see page 56).
Recommended Specialty Tools
Suction Cups (94400914)
Large Level (or Laser Level)

10 Installation (for qualified installers only)
© Travis Industries 9/25/17-1468 Maestro
Massachusetts Requirements
NOTE: The following requirements reference various Massachusetts and national codes not contained in this document.
Requirements for the Commonwealth of Massachusetts
For all side wall horizontally vented gas fueled equipment installed in every dwelling, building or structure used in whole or in
part for residential purposes, including those owned or operated by the Commonwealth and where the side wall exhaust vent
termination is less than seven (7) feet above finished grade in the area of the venting, including but not limited to decks and
porches, the following requirements shall be satisfied:
Installation of Carbon Monoxide Detectors
At the time of installation of the side wall horizontal vented gas fueled equipment, the installing plumber or gasfitter shall
observe that a hard wired carbon monoxide detector with an alarm and battery back-up is installed on the floor level where the
gas equipment is to be installed. In addition, the installing plumber or gasfitter shall observe that a battery operated or hard
wired carbon monoxide detector with an alarm is installed on each additional level of the dwelling, building or structure served
by the side wall horizontal vented gas fueled equipment. It shall be the responsibility of the property owner to secure the
services of qualified licensed professionals for the installation of hard wired carbon monoxide detectors.
In the event that the side wall horizontally vented gas fueled equipment is installed in a crawl space or an attic, the hard wired
carbon monoxide detector with alarm and battery back-up may be installed on the next adjacent floor level.
In the event that the requirements of this subdivision cannot be met at the time of completion of installation, the owner shall
have a period of thirty (30) days to comply with the above requirements; provided, however, that during said thirty (30) day
period, a battery operated carbon monoxide detector with an alarm shall be installed.
Approved Carbon Monoxide Detectors
Each carbon monoxide detector as required in accordance with the above provisions shall comply with NFPA 720 and be
ANSI/UL 2034 listed and IAS certified.
Signage
A metal or plastic identification plate shall be permanently mounted to the exterior of the building at a minimum height of eight
(8) feet above grade directly in line with the exhaust vent terminal for the horizontally vented gas fueled heating appliance or
equipment. The sign shall read, in print size no less than one-half (1/2) inch in size, “GAS VENT DIRECTLY BELOW. KEEP
CLEAR OF ALL OBSTRUCTIONS”.
Inspection
The state or local gas inspector of the side wall horizontally vented gas fueled equipment shall not approve the installation
unless, upon inspection, the inspector observes carbon monoxide detectors and signage installed in accordance with the
provisions of 248 CMR 5.08(2)(a)1 through 4.
Exemptions
The following equipment is exempt from 248 CMR 5.08(2)(a)1 through 4:
• The equipment listed in Chapter 10 entitled “Equipment Not Required To Be Vented” in the most current edition of NFPA 54
as adopted by the Board; and
• Product Approved side wall horizontally vented gas fueled equipment installed in a room or structure separate from the
dwelling, building or structure used in whole or in part for residential purposes.
MANUFACTURER REQUIREMENTS
Gas Equipment Venting System Provided
When the manufacturer of Product Approved side wall horizontally vented gas equipment provides a venting system design or
venting system components with the equipment, the instructions provided by the manufacturer for installation of the equipment
and the venting system shall include:
• Detailed instructions for the installation of the venting system design or the venting system components; and
• A complete parts list for the venting system design or venting system.
Gas Equipment Venting System NOT Provided
When the manufacturer of a Product Approved side wall horizontally vented gas fueled equipment does not provide the parts
for venting the flue gases, but identifies “special venting systems”, the following requirements shall be satisfied by the
manufacturer:
• The referenced “special venting system” instructions shall be included with the appliance or equipment installation
instructions; and
• The “special venting systems” shall be Product Approved by the Board, and the instructions for that system shall include a
parts list and detailed installation instructions.
A copy of all installation instructions for all Product Approved side wall horizontally vented gas fueled equipment, all venting
instructions, all parts lists for venting instructions, and/or all venting design instructions shall remain with the appliance or
equipment at the completion of the installation.
See Gas Connection section for additional Commonwealth of Massachusetts requirements.

Installation (for qualified installers only) 11
© Travis Industries 9/25/17-1468 Maestro
Alignment Track Installation
The alignment track is optional. We recommend using the track because it helps solidify the
base of the fireplace and it allows the fireplace to be anchored at the base.
The alignment track is secured to the platform (or sub-floor). The freplace is then placed on top of it.
Before attaching the alignment track, make sure the platform (or sub-floor) is level and capable of
supporting the fireplace and vent. Use minimum ¾” plywood for the platform.
NOTE: The Maestro alignment track is a single piece – disregard steps “a” and “b” below.
Verify the Alignment Track is Level Before Proceeding
Use a level to verify the alignment track is level (check several spots across the entire
length). Use shims (or washers/spacers) under the track, if necessary, to make sure the
track is level.
a
b
3.375" 86mm
c
3.375" 86mm
3.375" 86mm

12 Installation (for qualified installers only)
© Travis Industries 9/25/17-1468 Maestro
Secure the Fireplace to the Alignment Track
The alignment track as hoirzontal holes that allow
for the fireplace to be secured to the track. Make
sure the fireplace is correctly positioneed left to
right, then use #8 zip screws to secure the fireplace
to the track.
Fireplace Placement Requirements
This appliance may be installed into a residential or commercial/public space.
Fireplace must be installed on a level surface capable of supporting the fireplace and vent
Fireplace must be placed directly on wood or non-combustible surface (not on linoleum or carpet)
Fireplace should be located out of traffic and away from furniture and draperies.
Fireplace may be placed in a bedroom.
Clearances
(a) Clearance to Sides of Fireplace: 0”.
(b) Clearance to Back of Fireplace: 0”.
(c) Clearance to Front of Fireplace: 0”.
NOTE: do not cover the glass opening with any material.
NOTE: Side walls may be placed directly to the side of the fireplace.
(d) Clearance to Top of Fireplace: 0”
(e) Clearance to Bottom of Fireplace: 0” (may be placed directly on subfloor).
(f) Clearance to Vent 1” (25mm)
Raised Fireplaces
The fireplace (and hearth, if desired) may be placed on a platform designed to support the fireplace
and vent.
The base of the platform must be a minimum ¾” plywood (or equivalent). This provides the
necessary support for the fireplace runners.
HINT: We typically have displayed this fireplace on a 0” to 36” raised platform. Keep in mind that the
firebox opening (base of the flames) is 12” above the base. Desired position may vary depending
upon room size, typical viewing angle, and aesthetic intent.







b




a
c
Top of
Fireplace Side of
Fireplace

e
f
d

Installation (for qualified installers only) 13
© Travis Industries 9/25/17-1468 Maestro
Typical Framing Dims. – One Sided Configuration
Important Notes Regarding Framing
We strongly suggest framing around the fireplace after it is in place. If you do frame before
fireplace placement, add 6” to each side to allow for fireplace access.
Minimum Framing Dimensions
Version Width (x) Height (y) –
36” Glass Height (y) – 48” Glass Height (y) – 58” Glass
36” Single Sided 38.5” (978mm) 74-5/8”
(1896mm) 86-5/8” (2201mm) 96-5/8” (2455mm)
48” Single Sided 50.5” (1283mm) 86-5/8”
(2201mm)
19.75"
502mm
xy
3" (77mm) Maximum for vent clearance.
Do not place vertical framing directly in the
center above the fireplace - it will infringe
upon the vent clearance requirements.

14 Installation (for qualified installers only)
© Travis Industries 9/25/17-1468 Maestro
Typical Framing Dims. – See Through Configuration
Important Notes Regarding Framing
We strongly suggest framing around the fireplace after it is in place. If you do frame before
fireplace placement, add 6” to each side to allow for fireplace access.
Minimum Framing Dimensions
Version Width (x) Height (y) –
36” Glass Height (y) – 48” Glass Height (y) – 58” Glass
36” See Through 38.5” (978mm) 74-5/8”
(1896mm) 86-5/8” (2201mm) 96-5/8” (2455mm)
48” See Through 50.5” (1283mm) 86-5/8”
(2201mm)
19.625"
499mm
When using a top plate, you may need to notch it at
the center to provide adequate vent clearance.
3" (77mm) Maximum for vent clearance.
Do not place vertical framing directly in the
center above the fireplace - it will infringe
upon the vent clearance requirements.
x
y

Installation (for qualified installers only) 15
© Travis Industries 9/25/17-1468 Maestro
Nailing Brackets
Side Nailing Brackets
The side nailing brackets
secure the fireplace to the side
framing. The number of
brackets vary depending upon
configuration (island
configurations do not have side
nailing brackets).
These brackets are shipped flat
against the side of the fireplace
(see “a” to the right). Remove
the 2 mounting screws, position
the bracket and secure (“b”).
After the fireplace is in place,
bend the bracket back ( “c”) and
secure it to the framing with
screws (“d”).
NOTE: Make sure the fireplace
is square and plumb before
securing to the framing (use
shims if necessary).


a
b
c
d

16 Installation (for qualified installers only)
© Travis Industries 9/25/17-1468 Maestro
Accessing Internal Components
Most internal components can be accessed by removing the front glass pane and intake air channel
media tray (see instructions below). If more extensive access is required, see “burner removal” on the
following page.
-- Turn off gas to the fireplace prior to accessing internal components to prevent accidental ignition.
-- Shut off electricity to the fireplace to protect internal circuits.
Remove the front outer glass pane (see page 53). Remove the intake air channel media tray.
At this point most of the internal components may be accessed (see descriptions below).
Internal Shut Off Valve Access
The internal shutoff is accessed following the directions above. The valve is positioned near the gas inlet
(left, right, or bottom).
NOTE: The shut off valve must be closed while pressure testing the gas line leading to the fireplace.
LED Controller
- May be placed on its side
- Ma
y
be on ri
g
ht side
LEFT SIDE RIGHT SIDE
Burner Air Shutte
r
Shutoff Valve
- May be on left side
Air Pressure
Switch
CENTER
Rheostat
Fireplace Controller Gas Control Valve
Power Vent Controller

Installation (for qualified installers only) 17
© Travis Industries 9/25/17-1468 Maestro
Burner Removal
Burner removal is only required if extensive access is needed (installing glass panes on indoor/outdoor
units, extensive service, etc.). Follow the directions below to remove the burners.
a) Follow the directions on the previous page for accessing internal components (remove intake air
channel media tray).
b) Remove the front inner glass pane (see page 53).
c) Remove the screws holding the burner media trays in place (6 to 8 screws for each tray depending
upon length – see photos below).
d) Remove the media trays (use a flat screwdriver to pry up one edge). Make sure to notate the position
of the trays when removing. The screw holes will only line up if the tray is properly replaced.
1/4" Nutdriver

18 Installation (for qualified installers only)
© Travis Industries 9/25/17-1468 Maestro
e) Remove the burner lock-down bracket (it is held in place with a single screw). .
f) Lift the burner up and out of the fireplace. Remove the burner supports.
Maestro Fireplaces
The Maestro fireplace uses the burner shown below. When adjusting the air shutter make sure to adjust
both mixing tubes simultaneously

Installation (for qualified installers only) 19
© Travis Industries 9/25/17-1468 Maestro
Gas Line Requirements
MAKE SURE YOU ARE SUPPLYING AN ADEQUATE SUPPLY OF GAS (NG OR LP)
This fireplace, depending upon configuration, consumes a large amount of BTUs. Make sure
your gas line is properly sized to provide an adequate supply of gas.
MASSACHUSETTS INSTALLATIONS - WARNING:
THIS PRODUCT MUST BE INSTALLED BY A LICENSED PLUMBER OR GAS FITTER WHEN INSTALLED WITHIN THE
COMMONWEALTH OF MASSACHUSETTS.
OTHER MASSACHUSETTS CODE REQUIREMENTS:
Flexible connector must not be longer than 36 inches.
Shutoff valve must be a “T” handle gas cock.
Only direct vent sealed combustion products are approved for bedrooms or bathrooms.
Fireplace dampers must be removed or welded in the open position prior to the installation of a fireplace insert or gas log.
A carbon monoxide (CO) detector is required in the same room as the appliance.
The gas line must be installed in accordance with all local codes, if any; if not, follow ANSI 223.1 and
the requirements listed below.
The fireplace and gas control valve must be disconnected from the gas supply piping during any
pressure testing of that system at test pressures in excess of 1/2 psig (3.5 kPA). For pressures under
1/2 psig (3.5 kPA), isolate the gas supply piping by closing the manual shutoff valve.
Leak test all gas line joints and the gas control valve prior to and after starting the fireplace.
The fireplace has an internal shutoff valve. An additional shutoff valve is required. It must be
accessible and within 6’ of the fireplace.
Fuel
This fireplace is designed either for natural gas or for propane (but not for both).
Gas Line Connection
Installation must be performed by a qualified installer, service agency or the gas supplier (In Massachusetts a
licensed plumber/gasfitter).
Gas Inlet Pressure Maximum Input Pressure Minimum Input Pressure
Natural Gas 7" W.C. (1.74 kPA) 5.5” W.C. (1.37 kPA)
Propane 13" W.C. (3.23 kPA) 11” W.C. (2.74 kPA)
If the pressure is not sufficient, make sure the piping used is large enough, the supply regulator is adequately
adjusted, and the total gas load for the residence does not exceed the amount supplied.
The supply regulator (the regulator that attaches directly to the residence inlet or to the propane tank) should
supply gas at the input pressure listed above. Contact the local gas supplier if the regulator is at an improper
pressure.
Directions for Connecting a Gas Pressure Test Gauge
The gas control valve (shown to the left) has two accessible ports for testing line pressure and output
pressure. Loosen the brass screw on either test port and place a 5/16” i.d. rubber or plastic tubing over
the tapered test port. Connect the tubing to the test gauge.
WARNING: The brass screw must be tightened after testing to prevent gas leakage.
Input pressure Output pressure

20 Installation (for qualified installers only)
© Travis Industries 9/25/17-1468 Maestro
Gas Inlet Location
Gas inlet is determined by fireplace configuration and how the fireplace was ordered. Refer to the
dimensions pages for the configuration being used to determine what options are available. When
ordering the fireplace, the gas inlet is either from the side (left or right) or from the base (left or right).
Gas Inlet
The gas inlet is on the side (not available from the base).
The gas line may be
repositioned to the back.
1"
(25mm)
4.5" (115mm)

Front
4" (102mm)