Dawlance DWHB 875 User manual

MODEL: DWHB 875
Hand Blender
User Manual
Before using your Hand Blender please read this manual carefully
and keep it for future reference.
Read This Manual
Inside you will find many helpful hints on how to use and maintain your Hand Blender properly. Just
a little preventation care on your part can save you a great deal of time and money over the life of
your Hand Blender. You’ll find many answers to common problems in the chart of troubleshooting
tips. If you review the chart of troubleshooting tips first, you may not need to call for service.

K
J
L
M
F
E
D
C
I
HG
A
B
C
E
F
H
G
I
L
M
K
J
D

2
SAFETYAND SET-UP________________________
Please read this instruction manual thoroughly
prior to using this appliance! Follow all safety
instructions in order to avoid damages due to
improper use!
Keep the instruction manual for future reference.
Should this appliance be given to a third party,
than this instruction manual must also be handed
over.
The blades are very sharp! Handle the sharp
blades with utmost care, especially during
removing and cleaning, in order to avoid
injuries.
Never clean the appliance with bare hands.
Use always a brush.
Do not touch any moving parts of the
appliance. Do not attach or remove the parts
until the unit comes to a full stop.
Always keep hair, clothing and any other
utensils away from the appliance during
operation in order to prevent injury and
damages.
The appliance is intended for domestic use
only.
Check if the mains voltage on the rating label
corresponds to your local mains supply. The
only way to disconnect the appliance from
the mains is to pull out the plug.
Do not wrap the power cord around the
appliance.
For additional protection, this appliance
should be connected to a household faulty
current protection switch with no more than
30 mA. Consult your electrician for advice.
Do not immerse the appliance, power cord
or power plug in water or in other liquids.
Always pull out the power plug before
assembling the appliance, after using the
appliance, before disassembling, before
cleaning the appliance, before leaving the
room or if a fault occurs. Do not disconnect
the plug by pulling on the cord.
Prevent damage to the power cord by not
squeezing, bending or rubbing it on sharp
edges. Keep the cord away from hot surfaces
and open ames.
Do not use an extension cord with the
appliance.
Never use the appliance if the power cord or
the appliance is damaged.
Our Household Appliances meet applicable
safety standards, thus if the appliance or power
cord is damaged, it must be repaired or replaced
by the dealer, a service centre or a similarly
qualied and authorized service person to
avoid any dangers. Faulty or unqualied repair
work may cause danger and risks to the user.
Do not dismantle the appliance under any
circumstances. No warranty claims are
accepted for damage caused by improper
handling.
Keep the appliance always out of the reach
of children.
The appliance should not be used by the
following persons, including children: those
with limited physical, sensory or mental
capabilities and also those with a lack of
experience and knowledge. This does not
apply to the latter if they were instructed
in the use of the appliance or if they use it
under the supervision of a person responsible
for their safety. Children should always be
supervised to ensure that they do not play
with the appliance.
Do not leave the appliance unattended as
long as it is in use. Extreme caution is advised
when the appliance is being used near
children and people with limited physical,
sensory or mental capabilities.
Before using of the appliance for rst time,
clean all parts which come into contact
with food carefully. Please see details in the
“Cleaning and Care” section.
Dry the appliance and all parts before
connecting it to the mains supply and before
attaching the accessories.
Do not operate the appliance without the
ingredients in the measuring beaker or
chopper.
Never place the appliance, attachments,
power cord or plug on hot surfaces such as
gas burner, electric burner, heated oven or
hot liquids and foods. Leave hot food and
liquids cool down to min. 80°C or less,
before operation.
Do not use the appliance for anything other
than its intended use.
Never switch on the appliance for longer as
you need to process the food.

3
Never use the appliance with damp or wet
hands.
Operate the appliance with delivered parts
only.
The appliance is constructed to process only
common household quantities.
Do not use the appliance if the blades are
damaged or show signs of wear.
Always use the appliance on a stable, at,
clean and dry surface.
Make sure that that there is no danger that
the power cord could be accidentally pulled
or that someone could trip over it when the
appliance is in use.
Position the appliance in such a way that the
plug is always accessible.
A spatula may be used to remove the food
from the measuring beaker or chopping
bowl. To do this, the appliance must be
switched o.
This appliance is not suitable for crushing ice
or for dry or hard foods as the blades will
become dull quickly.
Remove bones and stones from food to
prevent the blades or the appliance from
becoming damaged.
In order to reduce the risk of injury, never set
the blades of the appliance onto the base, if
the chopper is not sitting properly.
Make sure that the cover of the chopper
is sitting properly before you switch on the
appliance.
This appliance should not be in operation for
longer than 15 seconds if it is not processing
anything.
This appliance is intended for short periods
of use and may not be used for longer than
1 minute (hand blender or chopper) or 3
minutes (whisk) at a time. After use, let the
appliance cool down suciently.
SAFETYAND SET-UP________________________
AT A GLANCE ______________________________
Dear Customer,
Congratulations on the purchase of your new
Hand Blender DWHB 875.
Please read the following user notes carefully to
ensure you can enjoy your quality product from
for many years to come.
Special features
The appliance is perfectly suitable for preparing
of sauces, dips, soups, mayonnaise and
baby food, as well as for mixing drinks and
milkshakes, chopping of vegetables, culinary
herbs, meat, fruits, nuts and cheese.
The Hand Blender is equipped with;
Powerful 400 Watt motor.
High-quality stainless steel blender,
blades and-balloon whisk attachment.
900ml chopping bowl.
Multifunctional measuring beaker.
Maximum quantities and
processing time
Refer to the table for the maximum quantities
and processing time
Ingredients Maximum
quantities
Processing time
Meat/sh
Herbs
Nuts
Cheese
Bread
Eggs
(hard-boiled)
Onions
(cut in 8 pieces)
200 g
20
200
150 g
1 slice
2 egg
100 g
10-15 seconds
20 seconds
15 seconds
15 seconds
20 seconds
5 seconds
10 seconds

4
Preparation
1Remove all packaging and sticker materials
and dispose of them according to the
applicable legal regulation.
2Before using of the appliance for rst time,
clean parts which come into contact with food
(See the “Cleaning and care” section).
3Prepare the food in small pieces before using
the appliance.
Blending
1Put the food that you would like to puree or
mix in the measuring beaker or in any
I
other similar bowl.
2Connect the base unit to the blender by
E G
putting the blender onto the base unit. Turn
the base unit to the left.
Make sure the blender is properly attached to
the base unit.
3 Insert the plug into the wall socket.
B
4 Immerse the blender in the measuring
G
beaker , where the ingredients to be
I
blended are.
Note
To prevent the ingredients from splashing, do
not press the On/Obutton level I and
C
On/Obutton level II until the blender has
D
been immersed in the ingredients.
5Press and hold down the On/Obutton level
I C.
Notes
Always use the appliance on level I. If
necessary, press and hold down the On/O
button level II . Once you release the On/
Obutton level I , the appliance switches
oautomatically.
Do not use the appliance for longer than one
minute at a time.
6Move the appliance slowly up and down and
in circles to blend the ingredients.
7 Release the On/Obutton level I or On/
Obutton level II when you nish the
process and disconnect the power plug from
the socket.
8 Remove the mixture from the measuring
beaker .
9 Disassemble the blender from the base unit
Eby turning the base unit to the right and
pulling it o.
Notes
Do not overll the measuring beaker or
I
other similar bowl to prevent the mixture
from overowing. Smaller amounts can be
processed easier.
If you would like to use the blender directly
in the cooking pot, rst take the cooking pot
out othe stove to prevent the blender from
overheating.
Do not operate the appliance continuously
for more than 1 minute, in order to prevent
overheating of the appliance.
Never switch on the appliance for longer as
you need to process the food.
AT A GLANCE ______________________________
OPERATION_______________________________
Controls, parts and accessories
See the illustration on page 3.
Controls and parts
AHanging loop
BPower cord and plug
COn/Obutton, level I
DOn/Obutton, level II
EBase unit
FWhisk holder
GBlender
HBalloon whisk
IMeasuring beaker
JChopper lid
KChopping blade
LChopping bowl
Accessories
MWall mounting attachment
2 x screws
2 x dowels
Note
Your Hand Blender has been designed for
small quantities of food and should not be
used for any other application.
D
C
C
D
I
G
-The appliance starts operating.

5
OPERATION_______________________________
Chopping
Notes
Do not chop extremely hard items such as
coee beans, ice cubes, nutmeg, grains and
bones. Remove stalks from herbs, shells from
nuts, bones, tendons and gristle from meat.
Prepare the food in small pieces (total max.
200 g).
1 Put the chopping bowl on a stable, at,
clean and dry surface.
2 Place the chopping blade onto the spindle
in the chopping bowl .
L
1
Caution
The chopping blade is very sharp, be careful
while placing the chopping blade .
K
Do not touch the chopping blade with bare
hands.
3Place the ingredients in the chopping bowl .
4Put the chopper lid onto the chopping
bowl .
L
5 Put the base unit onto the chopper lid .
J
Turn the base unit to the left so that it is rmly
locked into place. Make sure the base unit is
securely attached to the chopper unit.
32
Note
During operation always hold the chopping
bowl with one hand to prevent falling over.
6 Insert the plug into the wall socket.
7 Press and hold down the On/Obutton level
II .
D
Notes
Do not use the chopper for longer than 1
minute at a time.
You will achieve the best results if you press
the On/Obutton, level II intermittently.
8Release the On/Obutton level II when
you nish the process and disconnect the
power plug from the wall socket.
9 Disassemble the base unit from the
chopper lid by turning the base unit to the
right and pulling it o.
10 Take the chopper lid o. Take the
chopping blade out of the chopping bowl
Lcarefully prior to emptying the chopped
food.
Note
If the chopper does not work or if the
chopping blade only turns slowly, rst pull
out the power plug . Then take the base
unit and the chopper lid o. Check the
chopping bowl to see if there is something
blocking the chopping blade. Maybe you put
too much hard food in the chopping bowl.
If the ingredients stick to the side of the
chopping bowl , a spatula may be used to
remove the food from the chopping bowl. To
do this, the appliance must be switched o.
Do not operate the appliance continuously
for more than 1 minute, in order to prevent
overheating of the appliance.
Caution
Do not touch the chopping blade with your
bare hands. The chopping blade is very
sharp.
L
K
L
J
E
B
-The appliance starts operating.
D
D
E
J
J
K
K
B
E J
L
L

6
OPERATION_______________________________
Whisking
Notes
You can use the balloon whisk for
whipping cream and beating eggs.
Never use more than 4 egg whites or 400 ml
cream.
1 Put the balloon whisk onto the whisk holder
Funtil it clicks into place.
2 Connect the base unit to the whisk holder
Fby putting the whisk holder onto the base
unit. Turn the base unit to the left. Make sure
that the whisk holder is securely attached into
the base unit.
3 Put the ingredients that you would like to
process in the measuring beaker or in any
other similar bowl.
4 Connect the power plug into the wall
socket.
5 Hold the balloon whisk into the mixture to
be processed.
6 Press and hold the On/Obutton level I or
II D.
7 Move the appliance slowly up and down and
in circles to whisk the ingredients.
8 Release the On/Obutton level I
or II
when you nish the process and disconnect
the power plug from the wall socket.
9 Remove the mixture from the measuring
beaker .
10 Disassemble the base unit from the whisk
E
holder by turning the base unit to the right
and pulling it o.
Note
Do not operate the appliance for longer than
3 minutes at a time.
Do not overll the measuringbeaker , or
the similarbowl to prevent the mixture from
overowing. Smalleramounts can be processed
easier.
If you would like to use the balloon whisk
directly in the cooking pot, rst take the
cooking pot out othe stove to prevent the
balloon whisk from overheating.
Caution
Make sure that you do not drill into electrical
lines or water pipes!
2Secure the wall mounting attachment to the
wall using the supplied screws and dowels.
3You can place the base unit on the wall
mounting attachment .
M
Note
The base unit can also be hung on a hook with
the hanging loop .
A
INFORMATION ____________________________
You can put your appliance to a practical place
by mounting the wall mounting attachment.
1Hold the wall mounting attachment in
the desired position on the wall. Mark the
two drill holes. Drill the holes and insert the
supplied dowels.
Installing the wall mounting
attachment
H
H
E
I
B
H
C
-The appliance starts operating.
M
C D
I
F
I
M
E

7
INFORMATION ____________________________
Cleaning and care
Caution
Never use petrol, solvents or abrasive
cleaners, metal objects or hard brushes to
clean the appliance.
Do not touch the chopping blades with bare
hands. The blades are very sharp. Use a
brush!
Never put the base unit or power cord
in water or any other liquids and never hold
them under running water.
1 Turn the appliance oand disconnect it from
the wall socket.
2 Let the appliance cool down completely.
3
Use a damp soft cloth to clean the base unit .
4 Immediately after using, clean the blender ,
chopper lid and whisk holder with warm,
soapy water and dry them thoroughly. Never
submerge them in dishwater.
5
Only the following parts can be cleaned in
dishwasher: balloon whisk , chopping bowl ,
chopping blade and measuring beaker .
I
Note
Before using or storing the appliance after
cleaning, dry all parts carefully using a soft
towel.
Storage
If you do not want to use the hand blender for a
long period of time, please store it carefully.
Make sure the appliance is unplugged and
completely dry.
Store it in a cool, dry place.
Make sure the appliance is always kept out of
reach of children.
Environmentalnote
This product has been made from high-quality
material and parts, which can be reused and
are also suitable for recycling.
Therefore, do not dispose of the
product along with normal
household waste at the end of its
service life. Take it to a collection
point for the recycling of electrical
and electronic equipment. This is
indicated by this symbol on the
product, in the operating manual and on the
packaging.
Reusing and recycling of old appliances is
an important contribution for protecting our
environment.
Technical data
This product conforms to the European
directives 2004/108/EC and
2006/95/EC
Power supply: V042–022 ~, 50 Hz
Power: 00 W
Noise level: 1M≤80dBA
Technical and design modications reserved.
Please consult your local authorities to nd out
where the nearest collection point is.
4
E
E
G
J F
H L
K
Note: Not recommended for commercial use.