Daxom Naviels ukdax-10edt User manual

Dear Daxom User, For correct operation and safety of this device, follow the instructions in this manual during installation and use. Unauthorised assembly or maintenance

of this device will void the warranty, and our company will not be responsible for any defects or accidents that may occur with the product. Please keep this instruction

manual in good condition for future reference.

SAFETY WARNINGS

1. The boiler must be installed by qualified tradespeople (electrician/plumber) according to the instructions in this manual.

2. The boiler must initially be started up by a qualified technician , do not attempt to start the device yourself.

3. The boiler must be safely and securely connected to the water and heating system .

4. Ensure that the mains voltage is correct. (Please note: Depending on the model, the voltage specified may differ)

5. If using an external electricity source ( (such as a generator) safe operation of the boiler must be ensured.

6. Install the appliance with the appropriate diameter cable specified in this manual. The boiler needs to be connected via a MCB/RCD as outlined in this instruction manual

and secure earth grounding needs to be in place for safe operation.

7. This appliance should not be installed in humid or external environments.

8. Do not store flammable or explosive substances or articles near the appliance.

9. This installation and operating manual is part of the product. Keep it for reference.

10. This boiler should only be used for its intended purpose. The manufacturer rejects all contractual or non-contractual obligations in advance for damage to property or

injury to persons or animals resulting from misuse, installation, adjustment and maintenance.

11.After removing the packaging, make sure all parts are included and in good condition. If parts are missing or damaged, contact the retailer where you purchased your

boiler.

12. The safety valve outlet must be connected to the appropriate drain and ventilation system. The manufacturer disclaims all liability in the event of damage caused by

any intervention to the safety valve.

13. Carefully dispose of all packaging.

14. In case of water leakage, the water supply must be switched off and the manufacturer needs to be immediately informed.

15. The operating pressure of the hydraulic system must be between 1 and 2 bars and therefore must not exceed 3 bars. If necessary, the pressure may be reset as

shown in the paragraph "Filling the System".

16.If the boiler is not going to be used for a long time, it is recommended to perform the following steps:

•Turn off the power switch

•Drain the water in both the heating and hot water circuits, and close off the taps to prevent freezing.

17. The boiler should not be used by children without supervision.

18.In case of a smoke or burn smell originating from the device, turn off the power switch and contact the manufacturer.

19. Do not touch the device with wet hands or when the outside of the device is wet.

20.Do not use chemicals such as detergents or thinners for cleaning the boiler. Turn off power to the appliance, and then clean the exterior of the appliance with a slightly

damp cloth.

21. The first time you turn on the hot water tap, the water coming out may be of a very high temperature. Please take care and check the water temperature.

2. RECOMMENDATIONS FOR ECONOMICAL USE

1.Adjust the indoor temperature settings to your needs.

2. Having the heating operation set according to your intended use will increase energy

savings.

3. Savings can be made by adjusting the required temperature value for each

section (of the property with thermostatic radiator valves), However,

simultaneous use of a room thermostat and thermostatic valves may cause

problems.

4. It is important to position the room thermostat away from objects, such as

curtains, articles, etc., which could disrupt the ambient airflow.. This will ensure

that the device can correctly detect the temperature.

5. The room thermostat should be located at a suitable height and away from the

Boiler and other devices that would affect detection of the actual ambient

temperature.

6. Long-term ventilation of the heated environments will increases energy loss.

Short-term ventilation should be provided. If long-term ventilation is required,

closing the radiator valves or reducing the device temperature setting saves

energy.

7. Setting the boiler to a lower temperature overnight or when not at home will

save energy while maintaining the ambient temperature.

8. Setting the operating temperature of the device according to the outside

temperature saves energy.

9. Setting domestic water temperature to a moderate level saves energy.

3. CONFIGURATION OF YOUR DEVICE

4. TECHNICAL INFORMATION

5. BOILER ASSEMBLY

The boiler must be installed by a qualified technician.

5.1 Installation requirements and safety instructions

For ease of maintenance, observe the minimum distances specified in the installation in order to access the boiler.

For correct device positioning:

•Do not place above a stove hob or similar cooking appliances.

•Do not leave flammable products in the room where the boiler is installed

•Heat-sensitive walls (eg wooden walls) need proper insulation. Insulation must be installed between the wall and boiler.

• Before installation, carefully flush all system piping to remove any debris that may interfere with the operation of the boiler. In case of leakage due to overpressure of the

heating system, place a water collection funnel with a suitable drain pipe under the safety valve. There is no need for a safety valve in the mains hot water circuit, but make

sure that the water system does not exceed 6 bars. If in doubt, have a pressure reducer installed.

•The area where the boiler is installed must be free of obstructions and protrusions during repair or maintenance.

•The electrical connection of the boiler must be made with suitable cables, MCB/RCD and grounding must be installed.

5.2. Wall Mounting of the Boiler

The appliance must be installed exclusively on a vertical and solid wall that can support the weight of the boiler. M8 screws with appropriate anchors conforming to the type

of the wall itself are recommended.

5.2.1. Heating and Plumbing Connections

Pipe of appropriate diameter to ensure adequate circulation of the heating water must be used during installation. If the correct diameter heating pipes are not used,

constriction or blockages in the installation may result in insufficient heating circulation. Connections to the boiler should be easily detachable if necessary. Non return

Valves should be used with the inlet pipes.

5.2.1.1. Filling the Heating System for EDT and EDM Models

After the hydraulic connections have been made, the heating system must be filled. For UKDAX-xxEDT and UKDAX-xxEDM models, this is done with the filling tap under

the boiler. This should be done by following the instructions below:

•Make sure the cold water inlet tap is open

•Fill tap water until the pressure gauge reads between 1 to 1.5 bars.

•When filling is complete, close the filling tap.

•Discharge air accumulated in the radiators.

•Heating water pressure should be checked to make sure that it is between 1 and 1.5 bar after discharging the air in the radiators .

•Check to ensure there is no water leakage.

5.2.1.1. Filling the Heating System for ETT and ETM Models

After the hydraulic connections have been made, the heating system must be filled. For UKDAX-xxETT and UKDAX-xxETM models, this process is done via the filling

valve connected to the heating system. For this purpose, a connection with a valve must be made from the cold water supply to the heating circuit. Since this valve will be

used for filling the heating system, it is advisable to install it close to the device so that the pressure indicator is visible. A Non Return Valve must be must be installed after

the filling valve. Filling should be done by following the instructions below:

•Open the filling valve until the water pressure gauge is between 1 and 1.5 bar.

•Heating water pressure should be checked to make sure that it is between 1 and 1.5 bar after discharging the air in the radiators.

•Check to ensure there is no water leakage.

5.2.2. The Electrical Connections

The electrical installation must be carried out by a qualified electrician using suitable diameter cable determined according to the boiler capacity and cable length. The

MCB and RCD with appropriate characteristics and amperage which can cut the boiler electricity completely should be located separately and be close to the device. If

there is no earthing installation in the structure where the boiler is installed, the grounding line for the boiler should be installed by a qualified electrician. The Isolator switch

must be located near the boiler, and after the Isolator switch there must be enough cable to connect to the boiler. The connection of the cables to the boiler must be done

by a qualified installer. Cable diameters calculated according to boiler capacity and cable lengths, and MCB and RCD amperage values can be seen in the table below.

6. STARTING AND USING THE BOILER

6.1. Control Screen

The operating status of the device can be viewed on the control panel.

6.2. Control Keys

Use the buttons located under the LCD screen to control and program the boiler.

6.3. Operating the Device

The boiler installation must be carried out by qualified tradespeople.

Our company is not responsible for the damages and accidents that may occur due to installation by unauthorised tradespeople. Before starting the

boiler, all mechanical and electrical connections must be checked. During installation, the Combi boiler should be filled with water at a pressure between 1 to 2

bar. Our company is not responsible for damages and accidents that may occur due to incorrect connection. To start the boiler: Make sure that the water and

heating valves (heating valve only for ETT and ETM models) are open. Make sure that the fuse and residual current relay is in a position to prevent electrical

flow. After opening enough insulation from the ends of the electrical cables, loosen the screws on the connection terminal of the device. Insert the entire

conductive part of the cable and tighten the cable retaining the screw so that it is not slack. Make sure that the cable is fully and securely secured in place.

Repeat the procedure for the other cables to complete the connection.

Be sure to connect the cables to the correct place. Loose wiring may cause accidents. Turn on / switch on the residual current relay and then the fuse.

After all the indicator lights remain visible for a few seconds, the display will look like this.

Press and hold for 2 seconds to switch the device on. If the last setting was heating mode before the device was switched off, the appliance will start heating after

approx. 1 minute. will appear on the display. If the setting before the appliance was switched off was hot water mode only, the device switches to standby for hot water

use. A warning tone sounds each time you press a key. If the button is pressed for a longer time (eg 2-3 seconds), the button can not be pressed again until the beep

sounds.

6.4. Setting Operating Parameters

6.4.1. Setting the Day and Time

1.The device is switched off.

2. Press key for 5-6 seconds, when the days start flashing, set the day with or keys.

3.Press key, when the hour digit starts flashing, press the or to set the time between 0 and 23 hours.

4. Press key, when the minute digit starts flashing, press the or to set the minutes between 0 and 60.

5. Press key to save the settings or when no key is pressed for 10 seconds the boiler will save the settings and exit the setup menu.

6.4.2. Heating Temperature Adjustment

The device can be set between 35 and 80 degrees while operating in heating mode by pressing the or button The set heating temperature will start flashing 2

seconds after the adjustment is completed. After the display will show the operating temperature of the device on the display. It may take time for the device to reach the

set temperature.

6.4.3. Adjusting Domestic Water Temperature

Domestic water temperature can be adjusted in three ways:

1. While the device is delivering hot water, temperature can be adjusted using the or keys.

2. If the device is set for hot water only (summer mode), temperature can be adjusted in standby mode or while in operation with the or keys.

3. After switching to hot water heating mode (summer mode), press the key for 2-3 seconds. Then press until the “Shower” symbol is shown on

the display. Then temperature can be adjusted using the or keys. The temperature display will flash during adjustment. Two seconds after adjustment has

been completed, the display shows the new operating temperature of the device for heating and hot water .

6.4.4 Setting ΔT Over Temperature Difference

When the device goes into over-temperature mode, we can set the temperature difference that we want it to operate within.

1.Press the key for 2-3 seconds to enter the setup menu.

2.Press the until the temperature difference value symbol starts to flash. Use the or keys to adjust the temperature difference value ΔT.

4.Press to exit the setup menu.

6.4.5. Room Thermostat Adjustment

The boiler can be controlled with the room thermostat so that the boiler operates according to the temperature settings on the room thermostat. The room

thermostat connection needs to be activated by the Installer. After connecting the room thermostat to the boiler, turn on the room thermostat in the Boiler setting

menu. Even if the room thermostat is connected, the room thermostat does not function if it is not switched on in the setup menu. If the room thermostat function is

switched on while the room thermostat is not connected, the unit will remain in standby mode for heating and the device will not operate. The device room

thermostat symbol will appear when the thermostat function is set to on. To setup when the device is in normal operation;

1.Press the key for 2-3 seconds to enter the setup menu.

2.Press twice and the icon will appear, and the room thermostat on / off indicator will start flashing.

3.Use the buttons or to set the room thermostat to “1” and to close the room thermostat to “0.

4.Press to exit the setup menu.

6.4.6. Setting the Heating Mode

The device can be adjusted for underfloor heating (low temperature) and radiator heating. The device can be set to a maximum temperature of 55 oC when

operating in underfloor heating mode. If the device is connected to the underfloor heating system underfloor heating mode must be turned on by the Installer. This

ensures that the user can’t accidentally or deliberately change the heating mode to above 55 C.

When the device is set for radiator heating the radiator symbol is visible.

To set when the device is in normal operation;

1.Press the key for 2-3 seconds to enter the setup menu.

2.Pressing the key 3 times the symbol appears and the heating mode selection indicator starts flashing. Use the or keys to set the heating mode to “0

for underfloor heating or 1 for radiator heating.

4.Press the key to exit the setup menu.

6.4.7. Capacity Adjustment

The device can operate in 3 different capacities. P1 means 1/3 capacity, P2 means 2/3 capacity, P3 means full capacity. For example, if the device is 12 kw, P1: 4

Kw, P2: 8 Kw, P3: 12 Kw. Setup when the device is in normal operation;

1.Press the key for 2-3 seconds to enter the setup menu.

2.Press key 4 times and the icon appears (the capacity indicator). 3.Use the or buttons to set the device capacity to P1, P2 or P3. The symbol

brightness changes according to the selected capacity.

4.Press the key to exit the setup menu.

6.4.8. Setting the Operating Mode

The device can operate in 3 different operating modes.

1. Heater Only Mode: The boiler is set to heat only.

2. Hot Water Heating Mode Only: Device only heats domestic water. Also called summer mode.

3. Heater and Hot Domestic Water Heating Mode: The priority is domestic hot water heating. If the domestic hot water is needed when boiler is heating, , the boiler

stops heating and provides domestic hot water only.

When the device is in normal operation;

1. Press the key for 2-3 seconds to enter the setup menu.

2. Press the button 5 times, “heating”, “shower” or both start flashing according to the previous setting.

3. Use the or button to select the preferred operating mode.

4. Press the key to exit the setup menu.

6.5. Setting the Timer

The device can be programmed to heat on a daily and weekly basis. There are 21 program options in total and 3 per day. Program settings include program start

and end times, the operating temperature of the boiler for specific programs and the temperature difference ΔT that can be set. If the program is set and active, the

unit will be off heating mode during unscheduled time periods. The program can be activated or deactivated by pressing the button. When the program is active,

the current program, such as 1,2 or 3, appears on the screen. To enter the menu;

1.The key is pressed for 2-3 seconds. The setting menu is entered.

2. Press the key to enter the timer-setting menu.

3. Press the key until the week starts flashing. You can set the desired week or days with the or keys. The days of the week can be grouped as follows. •

•All days are selectable. (SUN. MON. TUES. WED. THUR. FRI. SAT.) Weekdays can be selected. (MON. TUES. WED. THUR. FRI.) Weekend days. (SUN. SAT.)

The days can be selected individually.

4.The key is pressed. Use the or buttons to select the desired program 1,2 or 3.

5.The key is pressed. Program start time will start flashing. Use the or buttons to set the program start time.

6.The key is pressed. Program start minute will start flashing. Use the or buttons to select the program start minute.

6.The key is pressed. The program end time will start flashing. Use the or keys to set the program end time.

7.The key is pressed. The program end minutes will start flashing. Use the or keys to set the program end minutes.

8.The key is pressed. The temperature display will start flashing. The operating temperature in the selected program is selected with the or keys.

9.The key is pressed. The temperature-setting indicator will start flashing. The desired heating temperature in the selected program is selected with the or

keys.

10. Press the when the programming is finished or if no key is pressed for 10 seconds, the settings are saved and the setting menu is exited.

6.6. Switching off

6.6.1. Temporary Shutdown

If the boiler will not be used for a short period press the button for 2-3 seconds to switch the device off. The boiler will be protected by the following systems

(leaving electricity and fuel supply active): Frost Protection Function: If the water temperature in the boiler falls below 5 ° C, the pump and heating will operate to

bring the water temperature back to a safe level (35 ° C). The symbol appears on the display during the anti-frost cycle. Anti-Blocking Function: The pump inside

the device and the three-way valve is activated every hour.

6.6.2. Long Term Closure

f you are not planning to operate the appliance for a longer period of time, switch off the power supply after pressing the button for 2-3 seconds. Drain the water

in the system to prevent the water freezing in the system (as the frost protection function is switched off)

7. ELECTRICAL DIAGRAM

8. REPAIRS AND SERVICE

We provide free repairs for material and production defects that occur during the warranty period of the product,. If you encounter any problems during use, please

contact our after-sales service department. Unauthorised repair and maintenance of the device will void the warranty. Our company will not be responsible for the