DCS BGA131 User manual

THE PROFESSIONAL
SIDE BURNER
Use and Care Guide
MODELS:
BGA131
BGA132
BGA131-BI
BGA132-BI

1
A MESSAGE TO OUR CUSTOMERS
We are glad that you selected the Professional Side Burner by DCS. Because this appliance contains features
not found on any other burner, we recommend that you read this entire booklet before your first use. Keep
it in a handy place as it has answers to questions that may occur during future use.
Feel free to contact us if we can help you. When you write please include the model number of the Burner.
We thank you for buying the Made in America Side Burner and wish you many years of enjoyment.
To help serve you better, please fill out and submit your Ownership Registration Card by visiting our website
at www.dcsappliances.com and selecting“Customer Service”on the home page and then select“Ownership
Registration” or submit the enclosed Ownership Registration Card to the address below. In addition, keep
this guide handy, as it will help answer questions that may arise as you use your new appliance.
For your convenience, product questions can be answered by a DCS Customer Service Representative by
phone: [phone], Fax: [phone], email: [email protected],
or by mail:
DCS
Attention: Customer Service
5800 Skylab Road
Huntington Beach, CA 92647
WARNING
Do not try lighting this appliance without reading the “Lighting Instructions”
section of this manual. Improper installation, adjustment, alteration, service
or maintenance can cause property damage, injury or death. Read the instal-
lation, operating and maintenance instructions thoroughly before use,
installing or servicing this equipment. This outdoor cooking gas appliance is
not intended to be installed in or on recreational vehicles and/or boats.
PRECAUTION
Do not store or use gasoline or other flammable vapors and liquids in the
vicinity of this or any other appliance.
FOR YOUR SAFETY
IF YOU SMELL GAS:
Shut off gas to the appliance
Extinguish any open flames.
Open lid.
If odor continues, immediately call your gas supplier.
Installation and service must be performed by a qualified installer, service
agency or the gas supplier.
PLEASE RETAIN THIS MANUAL FOR FUTURE REFERENCE.

TABLE OF CONTENTS
2
SAFETY PRACTICES AND PRECAUTIONS ..................................................................................................3-4
LOCATING THE PROFESSIONAL SIDE BURNER..........................................................................................5
GAS REQUIREMENTS
Natural Gas Hook-up..............................................................................................................................................6
LP Gas Hook-up........................................................................................................................................................7
LP Tank Requirements .......................................................................................................................................... 8
BUILT-IN INSTALLATION FOR MODELS BGA131-BI & BGA132-BI ..............................................9
CART INSTALLATION FOR MODELS BGA131 & BGA132 .................................................................10
LEAK TESTING AND LIGHTING INSTRUCTION
Lighting Instructions ..........................................................................................................................................11
Match Lighting.......................................................................................................................................................12
FINAL CHECKLIST ...........................................................................................................................................................13
GENERAL CLEANING....................................................................................................................................................13
BURNER REMOVAL ........................................................................................................................................................14
TROUBLESHOOTING ....................................................................................................................................................15
PAR TS LIST .....................................................................................................................................................................16-17
WIRING DIAGRAM..........................................................................................................................................................18
WARRAN T Y .........................................................................................................................................................................19
SERVICE ..................................................................................................................................................................................20

3
SAFETY PRACTICES & PRECAUTIONS
Improper use or installation is dangerous. Carefully follow these instructions.
Always remove the cover before lighting the Professional Side Burner. Never use the Side
Burner if a leak is present.
Do not use a flame to check for gas leaks.
Do not let children use the professional Side Burner.
Do not leave children unattended near the Side Burner.
Never let children crawl or hang on the Side Burner.
Exercise care when operating the Professional Side Burner. The burner grate can get hot
enough to cause burns during operation .
Never leave the Side Burner on unattended.
Always wait 5 minutes before relighting the burner to allow any accumulated gas to dissipate.
Should the burner go out during use, turn off the gas valve and wait 5 minutes before
attempting to relight. Always follow the lighting instructions. Never lean over a lit burner.
Never cook without the drip pan in place, pushed all the way to the rear of the burner box.
Use only in well ventilated areas.
Do not use in garages, breezeways, sheds, or other such enclosed areas.
Keep the area surrounding the Professional Side Burner clear and free from combustible
materials, gasoline, other flammable liquids or vapors, charcoal lighter fluid, and trash.
Do not obstruct the flow of combustion and ventilation air to the Professional Side Burner. On
cart mounted units keep area beneath the burner free of debris. If the burner is built-in do not
store gas cylinders beneath the unit without adequate ventilation.
CAUTION:
Do not store items of interest to children above or at the back of any appliance.
Children could be seriously injured if they should climb onto the appliance to
reach these items.
Keep the Professional Side Burner covered when not in use. Never connect an unregulated gas
line to the Professional Side Burner. If the Professional Side Burner has not been used for an
extended period of time (over winter, for example) the unit should be checked for gas leaks and
obstructions in the burner. Thoroughly clean the Professional Side Burner on a regular basis.
Only use the Professional Side Burner with the type of gas specified on the rating plate. To
change from LP gas to natural, or vice versa, a factory conversion kit (See page 6 for conversion
kit information) is required.

SAFETY PRACTICES & PRECAUTIONS
4
SPIDER AND INSECT WARNING!
Spiders and insects can nest in the burner(s) of this or any other gas appliance
and cause the gas to flow from the front of the burner. This is a very dangerous
condition which can cause a fire to occur behind the valve panel, thereby
damaging the unit and making it unsafe to operate.
You must inspect the burner(s) at least once a year or immediately if any of the
following conditions occur:
1. The smell of gas in conjunction with the burner flames appearing yellow.
2. The Professional Side Burner does not reach temperature.
3. The Professional Side Burner heats unevenly.
4. The burner(s) make popping noises.
Do not attempt to disconnect any gas connections while your burner is in use, or the gas supply
is on.
When the Professional Side Burner is stored indoors the gas supply must be disconnected and,
if using an LP gas cylinder, the cylinder must be stored outdoors in a well-ventilated area.
Keep any electrical supply cord away from the heated surfaces of the Professional Side Burner.
On cart mounted units, never move without first allowing the Side Burner and/or grill to cool
and ensuring that the gas supply is turned off. Fold the side shelf down, and push; never pull
the grill.
Never use the Professional Side Burner in a windy area.

5
LOCATING THE SIDE BURNER
1" min.
to combustible
material
1" min.
to combustible
material
1" min.
1" min.
6"
6"
COMBUSTIBLE
CONSTRUCTION
FIG.01
INSTALLATION OF BURNER:
A minimum of 6”from the back and sides must be maintained from the Professional Side Burner above
the cooking surface and a minimum of 1” below the cooking surface to combustible construction.
(Fig. 01)
When determining a suitable location take into account concerns such as exposure to wind, proximity
to traffic paths, and keeping any gas supply lines as short as possible. Locate the Side Burner only in a
well-ventilated area. Never locate the Side Burner in a garage, breezeway, shed, or other such enclosed
areas.
GAS REQUIREMENTS:
Verify the type of gas supply to be used, either natural or LP. Make sure the marked gas on the
appliance rating plate(s) and hook-up kit agrees with that of the supply.
Never connect an unregulated gas line to the appliance.
An installer supplied gas shut-off valve must be installed in an easily accessible location. All installer
supplied parts must conform to local codes, or in the absence of local codes, ANSI/NFPS-770-1984.
All pipe sealants must be an approved type and resistant to the actions of LP gases. Never use pipe
sealant on flare fittings.

GAS REQUIREMENTS
6
All gas connections should be made by a qualified technician and in accordance with local codes and
ordinances. In the absence of local codes, the installation must comply with the National Fuel Gas
Code ANSI Z223.1-1094.
Gas conversion kits are available from the factory. When ordering have the model number, and the
type of gas (natural or LP) which you need.
Total gas consumption of the Professional Side Burner with burner(s) on “HIGH”: Table 1 below.
TABLE 1
The appliance and its individual shut-off valve must be disconnected from the gas supply piping
system during any pressure testing of that system at test pressures in excess of 1/2 PSIG (3.5kPa.).
The appliance must be isolated from the gas supply piping system by closing its individual manual
shut-off valve during any pressure testing of the gas supply piping system at test pressures equal to or
less than 1/2 PSIG (3.5 kPa.).
The installation of this appliance must conform with local codes or in the absence of local codes, with
the national fuel gas code, ANSI Z223.1a-1987. Installation in Canada must be in accordance with the
Standard Can1-b149 and / or .2 (installation code for gas burning appliances and equipment) and local
codes.
NATURAL GAS HOOK-UP:
CONNECTION: 1/2” NPT male with 3/8” flare adapter.
OPERATING PRESSURE: 4.0”W.C.
SUPPLY PRESSURE: 5” to 14”W.C. if in excess of 14”W.C., a step down regulator is required.
Check with your local gas utility company or with local codes for instructions on installing gas supply
lines. Be sure to check on type and size of run, and how deep to bury the line. If the gas line is too
small, the Professional Side Burner will not function properly.
MODEL Btu/hr
BGA131 15,000
BGA131-BI 15,000
BGA132 30,000
BGA132-BI 30,000

7
GAS REQUIREMENTS
To hook-up the fittings supplied with the
Professional Side Burner, assemble as shown
in Fig.02. Use joint compound on male
threads only.
Do not use joint compound on the flare end of
the 1/2” NPT to 3/8” flare adapter. Ensure that
the regulator arrow points in the direction of
gas flow-towards the unit, away from the
supply.
Do not forget to place the installer-supplied
gas valve in an accessible location.
LP GAS HOOK-UP
CONNECTION: 1/2” NPT male with 3/8” flare
adapter (included).
OPERATING PRESSURE: 10.0”W.C.
Side Burner uses the LP regulator from
adjoining grill.
Apply joint compound to the threaded end of
the Side Burner gas inlet and tighten the
adapter to the pipe. Assemble the (2) 24”
hoses to the 3/8” flare tee, as shown in Fig.03.
Tighten the regulator hose to the remaining
fitting of the 3/8” flare tee.
Open Top
Manifold
Bottom of
131 &132 Burner
1/2" Coupling
1/2" Nipple
1/2" NPT to 3/8"
Flare Adapter
Regulator
To Gas Supply
FIG.02
FIG.03

GAS REQUIREMENTS
8
LP TANK REQUIREMENTS
A dented or rusty LP tank may be hazardous and should be checked by your LP supplier. Never
use a cylinder with a damaged valve.
The LP gas cylinder must be constructed and marked in accordance with the specifications for
LP gas cylinders of the U.S. Department of Transportation (DOT) and designed for use with a
Type 1 system only.
Do not change the regulator/hose assembly from that supplied with the unit or attempt to use
a Type 1 equipped regulator/hose assembly with a standard 510 POL tank/valve assembly. The
cylinder must be provided with a shut-off valve terminating in an LP gas supply cylinder valve
outlet specified, as applicable, for connection Type 1.
If the appliance is stored indoors, the cylinder must be disconnected and removed from the
appliance.
Cylinders must be stored outdoors in a well ventilated area out of the reach of children.
Gas must be turned off when not in use.

9
BUILT-IN INSTALLATION FOR BGA131-BI & BGA132-BI
The Professional Side Burner (BGA131-BI and BGA132-BI) is designed for easy placement into masonry
enclosures. Review the detail drawing below and take into account the provisions shown for the gas
line hook-up clearance in the left rear corner. (Fig. 04)
It is recommended that ventilation holes are provided in the enclosure in the event of a gas leak. The
counter and supporting ledges or deck must be level and flat.
IMPORTANT:
Gas fittings, regulator, and installer shut-off valves must be easily accessible.
22 -1/8" 2
"
25 -
1/2"
10-1/16"
25 - 1/2"
11-
3/4 "
2
"
14
-3/4"
Single Side Burner Dual Side Burner
Standard layout for non-combustible only.
12"
10 - 1/16"
2" X 2" opening
for gas supply line
A
MODEL A
BGA131-BI 12"
BGA132-BI 22-3/4"
10-1/16"
FIG.04

CART INSTALLATION FOR BGA131 & BGA132
10
2
"
10
2
"
10
-
BGA131 BGA132
REAR FRONT
IGNITION
BURNER IGNITION
12 -
3/4"
3/8"
15 -
3/4"
23 -
13
" 13
"
10
-
10
-
3/4"
-
3/4"
-
3/8
"
26
3/8" 3/8"

11
LEAK TESTING & LIGHTING INSTRUCTIONS
WARNING:
Do not smoke while leak testing. Extinguish all open flames.
Make a soap solution of one part liquid
detergent,and one part water. Never leak test
with an open flame. For LP units, check with a
full cylinder. Make sure all control valves are
in the “OFF” position. Turn the gas supply
“ON”.Check all connections from the supply
line (Fig. 02), or LP cylinder (Fig. 03) up to the
manifold pipe assembly (Fig. 06). Apply the
soap solution around the connection with a
spray bottle, brush, or rag. Soap bubbles will
appear where leak is present. If a leak is
present, turn off gas supply, tighten any
leaking fittings, turn gas on, and recheck.
WARNING: IMPORTANT!
Inspect the gas supply piping or hose prior to turning the gas “ON”. If there is
evidence of cuts, wear or abrasion, it must be replaced prior to use. Do not
use the Professional Side Burner if the odor of gas is present. Turn the control
knob to “OFF”, then turn on the gas supply. If using LP, is there gas in the
tank? Always keep your face and body as far away from the burner as
possible when lighting.
LIGHTING INSTRUCTIONS
Remove the burner cover, or any cooking utensils from
the burner grate. Push and turn the control knob
counterclockwise to the “HI” position. This will start the
gas flowing. Push and hold the ignition button next to
the burner knob. You’ll hear a snapping sound. At the
same time a spark will be provided at the burner
ignition. It may be necessary to engage the ignition
button until gas has filled the line. If the smell of gas is
detected and the ignition is not functioning,
immediately turn the control knob “OFF”. Allow 5
minutes for any accumulated gas to dissipate, then see
the following section for “Match Lighting”.
REAR FRONT
IGNITION
FIG. 07 BGA132-BI Shown
FIG.06
Ignition
Control
Knob

LIGHTING INSTRUCTIONS
12
MATCH LIGHTING
Hold a lit match near the burner ports, turn the control
knob counterclockwise to “HI”. Move your hand
immediately once the burner is lit. Rotate the control
knob to the desired setting. Check for proper burner
flame characteristics and adjust the air shutters if
necessary. (Fig. 08)
Each burner is adjusted prior to shipment; however,
variations in the local gas supply may make minor
adjustments necessary.
Burner flames should be blue and stable with no yellow
tips, excessive noise, or lifting (Fig. 09). If any of these
conditions exist check that the air shutter or burner
ports are not blocked. If the flame is yellow, indicating
insufficient air, turn the air shutter counterclockwise to
allow more air into the burner. If the flame is noisy and
tends to lift away from the burner, indicating too much
air, turn the air shutter clockwise to reduce the air
opening. To access the open burner air shutter, remove
the burner grate. The locking screw is on top of the
venturi, loosen, adjust, retighten. (See Page 14, Fig. 10)
3/8"
1-1/2"
FIG.08
FIG.09

13
FINAL CHECKLIST
Specified clearances maintained to combustibles.
Professional Side Burner is properly mounted.
All internal packaging removed.
Burner is seated and does not rock.
Each burner lights satisfactorily, individually or with adjacent burner lit.
Knob(s) turn freely. Bezel(s) centered.
Flame adjusted.
Pressure regulator connected and set for 4.0"W.C. Natural, 11.2"W.C. LP gas.
Manual shut-off valve installed and accessible.
Unit tested and free of leaks.
User informed of gas supply shut-off valve location.
Battery installed in module properly and generates ignition spark when activated.
PLEASE LEAVE THESE INSTRUCTIONS WITH THE USER.
USER, PLEASE RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.
GENERAL CLEANING
The Professional Side Burner will give you years of trouble free service if properly maintained. The
body panels and front valve panel and burner hanger are made from non-rusting high grade stainless
steel. The burner is a heavy duty cast iron and the venturi tube is aluminized steel.
STAINLESS STEEL
There are many different stainless steel cleaners available. Always use the mildest cleaning procedure
first, scrubbing in the direction of the grain. Do not use steel wool as it will scratch the surface. To
touch up noticeable scratches in the stainless steel, sand very lightly with dry 100 grit emery paper in
the direction of the grain.
SIDE BURNER GRATE
The side burner grate is porcelain enamel over cast iron for durability. To avoid burns do not clean a
hot grate. They may be wiped while in place with hot, soapy water, rinsed and wiped dry. Never
immerse a hot grate in water. Due to rapid temperature changes the porcelain may pop off the edges
of the grates. Do not be concerned as the base metal, cast iron, soon darkens to blend with the
porcelain enamel. Use care when wiping areas where the enamel has popped off, the edges may be
sharp. If cleaning necessitates grate removal, care should be taken in lifting them. They are very heavy.
Be sure to place them on a protected surface.
DRIP TRAY
A stainless aeration pan or drip tray with stainless steel handle is located under the burner. It collects
any boil-overs or spills. Pull forward to remove. Spills should be washed off as soon as possible to
prevent baked on soil.

BURNER REMOVAL
14
Ensure that the gas supply is off, and the knobs are in the “OFF” position. Make sure the Side Burner is
cool before removal.
TO REMOVE BURNER
Remove the burner grate. Grasp the burner, pull it up and slightly to the rear of the unit so that the
venturi tube comes off the brass orifice at the front, and remove.
BURNER CLEANING
Clean the exterior of the burner with a
wire brush. Clear any clogged burner
ports with a straightened paper clip.
Never enlarge the burner ports. Never
use a wooden toothpick as it may
break off and clog the port. Shake out
any debris through the air shutter. Use
a flashlight, as shown, to inspect the
burner inlet to ensure it is not blocked.
If obstructions can be seen, clear them
using a wire coat hanger that has been
straightened out.
ORIFICE CLEANING
With the burner(s) removed, shine a
flashlight into the orifice to ensure that there is no blockage. Use a needle to clear any debris. Remove
the orifice by unscrewing if the blockage cannot be removed and push it out from the inside. Never
enlarge the orifice.
RE-ASSEMBLY
Slide the air shutter opening of the venturi tube over the brass orifice at the front inside of the burner
box, then lower the burner head onto the support channel. Make sure the rectangular projection on
the bottom of the burner drops into the cut-out in the channel. Ensure that the burner is level and
does not rock. It is very important that the venturi tube is properly located on the orifice. Light all the
burner and check for proper flame characteristics.
INSPECT VENTURI
Clean with a wire if necessary
Air Shutter
FIG.10

15
TROUBLESHOOTING
Burner won’t light when the ignition
is pushed.
Burner flame is yellow or orange, in
conjunction with the odor of gas.
Low heat with knob in “HI” position.
Remove the burner grate. With the control knob in the“OFF”
position, watch the electrode while engaging the ignition.
You should see a spark jump inside the electrode cap.
If there is no spark........see ignition service.
If there is a spark... is there gas supplied to the unit and is the
line purged of air?
Does the other burner of a dual burner operate?
Check the orifice for blockage.
Check the burner inlet for obstructions.
Check the air shutter for proper adjustment.
Is the Side Burner in a dusty area? Move to less dusty area if
possible.
Is the fuel hose bent or kinked?
Is there adequate gas supply available? If it is only one
burner of the dual burner unit that appears low, does the
orifice or burner need cleaning?
If using LP gas, check for empty tank.
PROBLEM WHAT TO DO
Before replacing an ignition module, perform this simple test to check if the ignition module is
working or not. Remove the drip pan from under and behind the valve panel, look upward and locate
where the electrode wire is connected.
Disconnect the electrode wire and place the metal blade of a screw driver about an 1/8”from the metal
terminal on the back of the ignition module. Engage the ignition button. You will see sparks jump to
the screw driver if the ignition module is good. If the ignition module is good,you should examine the
wiring of the electrode for cracks or cuts. If there is no spark, remove and replace the ignition module
and reassemble.

SINGLE SIDE BURNER PARTS LIST
FOR BGA131 & BGA131-BI
16
NOTE: Part list typical for BGA131 & BGA131-BI models. Illustration shows BGA131-BI model.
ITEM DESCRIPTION PART NO.
1. BURNER COVER 32060-08
2. PULL HANDLE 18204-01
3. TOP GRATE BK 12020
4. OPEN TOP BURNER HEAD 30200-01
5. GASKET OPEN TOP 14000
6. VENTURI 12007-1
7. MANIFOLD (BGA131-BI MODEL) 18230-02
MANIFOLD (BGA131 MODEL) 18035-1
8. MANUAL GAS VALVE 13017-01
9. ORIFICE NATURAL 13005-49
ORIFICE LP 13005-56
10. OT ELECTRODE ASSEMBLY 30221-02
11 . BATTERY IGNITION MODULE 18355
ITEM DESCRIPTION PART NO.
12 1.5VDC BATTERY AAA 18356
13. CONTROL KNOB 14351
14. BEZEL 14006-PL
15. DRIP PAN HANDLE W/A DBI (BGA131-BI MODEL) 33035
DRIP PAN HANDLE W/A 131/132 (BGA131 MODEL) 32061
16. DRIP PAN ST.STL (BGA131-BI MODEL) 32348-02
DRIP PAN ST.STL (BGA131 MODEL) 31707-11
17. AERATION PAN 32033
18. BURNER HANGER 31705-01
19. VALVE PANEL (BGA131-BI MODEL) 32349-05-PA
VALVE PANEL (BGA131 MODEL) 33033-PA
20. VALVE PANEL SCREWS 15002-31
21. HEAT SHIELD (INSIDE) 30992
11
2
3
4
5
14 15 1613
17
6
12
18
7
8
19
9
20
10
21
1

17
DOUBLE SIDE BURNER PARTS LIST
FOR BGA132 & BGA132-BI
NOTE: Part list typical for BGA132 & BGA132-BI models. Illustration shows BGA132-BI model.
ITEM DESCRIPTION PART NO.
1. BURNER COVER 32060-09
2. PULL HANDLE 18204-01
3. TOP GRATE BK 12013-1
4. OPEN TOP BURNER HEAD 30200-01
5. GASKET OPEN TOP 14000
6. VENTURI FRONT 12007-1
7. MANIFOLD (BGA132-BI MODEL) 18230-01
MANIFOLD (BGA132 MODEL) 18035-2
8. MANUAL GAS VALVE 13017-01
9. ORIFICE NATURAL 13005-49
ORIFICE LP 13005-56
10. BEZEL 14006-PL
11. CONTROL KNOB 14351
ITEM DESCRIPTION PART NO.
12. BATTERY IGNITION MODULE 18355
13. 1.5VDC BATTERY AAA 18356
14. DRIP PAN HANDLE W/A DBI (BGA132-BI MODEL) 33035
DRIP PAN HANDLE W/A 131/132(BGA132 MODEL) 32061
15. DRIP PAN ST.STL (BGA132-BI MODEL) 32348-01
DRIP PAN ST.STL (BGA132 MODEL) 31707-21
16. AERATION PAN 32034
17. VENTURI BACK 12007-2
18. OT ELECTRODE ASSEMBLY 30221-02
19. BURNER HANGER, 36/48BQ 30568
20. VALVE PANEL (BGA132-BI MODEL) 32349-06-PA
VALVE PANEL (BGA32 MODEL) 33034-PA
21. VALVE PANEL SCREWS 15002-31
22. HEAT SHIELD (INSIDE) 30992
22
11
2
3
4
5
14 15
16
13
17
6
12
18
7
8
19
920
10 21
1

SINGLE & DOUBLE SIDE BURNER WIRING DIAGRAM
18
IGNITION SWITCH
18355
BATTERY
IGNITION MODULE
1.5 VOLT
ALKALINE
BATTERY
GND
TERMINAL
NOTE: HIGH VOLTAGE AT TERMINALS

19
WARRANT Y
LENGTH OF WARRANTY
Limited Five (5) year covers the cast iron burner(s), the structural integrity of the exterior and interior
body parts. Should deterioration occur to the degree of non-performance, a replacement will be
furnished.
DCS warrants all other Side Burner components to the original purchaser to be free of factory defects
in material and workmanship for a period of one (1) year from the original date of purchase.This does
not apply if the unit was subjected to other than normal residential use.
DCS WILL PAY FOR
All repair labor and replacement parts for one year, for parts found to be defective due to materials or
workmanship. Service must be provided by Authorized Factory Agent during normal working hours.
No charges will be made for repair or replacement at the factory for parts returned pre-paid through
the dealer and claimed within the warranty period and found by DCS to be defective.
Replacement will be F.O.B. DCS.
DCS WILL NOT PAY FOR
Correct the installation.
Instruct you how to use the equipment.
Repairs when the appliance is used on other than normal residential use.
Damage resulting from accident, alteration, misuse, abuse, hostile environments, improper
installation or installation not in accordance with local codes.
Chipping of porcelain enamel on the burner grates.
DCS will not be liable for transportation costs, labor costs of export duties.
Shipping Damage.
This warranty shall not apply, nor can we assume responsibility for damage that might result from
failure to follow manufactures instructions or local codes, where the appliance has been tampered
with or altered in anyway or which, in our judgement, has been subjected to misuse, negligence, or
accident.
This warranty is in lieu of all other warranties expressed or implied and all other obligations or liability
in connection with the sale of this appliance.
In order to provide warranty service an further improve our product, please fill out and send the
warranty card to the factory.