DD-EFI Pro Dash User manual

Pro Dash
Quickstart Guide

2 | P a g e
Digital Dash
Setup Video
Load Dashboard
Video
Main Connector
***CAUTION: Make sure to install a Jumper Wire (With Factory Resistor or Fuse) between the vehicle’s alternator
excite/sensing wire to the vehicles ignition wire when removing the instrument cluster or your alternator may not charge.
Software Setup & Configuration
If you have provided your TunerStudio Registration and Current Project to us, then
the below steps have already been completed for you.
Please move on to the I/O Connectors for wiring in your Digital and Analog Inputs
1. Wireless Connection –Click on Wireless Symbol (Bottom-Right) & complete network/password
2. TunerStudio Setup
➢Activate Registration –Go to Help -> Enter Registration
➢Disable “Check for Updates” –Go to Help and uncheck the “Automatic Update Check” box
➢Preferences Setup –Go to Options -> Preferences and Check Both:
•Load Last Project on startup
•Make Dashboards Full Screen
3. Load DDEFI Pro Dash Project
➢Click on “Open Last Project”
4. Load Dashboard
➢Right-click on dashboard screen
•Load / Save
•Load Dashboard
➢For DD-EFI default dashboards
•Check “Other”
•Click on the “…” on the right
•Click on Home
•Click on:
1. DD-EFI folder
2. Dashboards
3. Choose the dashboard you would like loaded

3 | P a g e
Sensor Connector
Wiring Video
I/O Connectors
The DD-EFI Pro Dash has (2) I/O Connectors for Sensors and Digital Inputs. Below are diagrams outlining what each Pins
location, function, and wire color in the 12 Pin and 10 Pin black connectors. Provided: Sensor and Digital Wiring
Harnesses, 2:6 Lever Lock Connector, (4) T-Tap Connectors (Used for: Fuel Level, L/R Turn Signals, High Beam)
Sensor Connector
•(5) ADC (Analog) Inputs:
oSensor 5, this is pre-configured in DD-EFI Dashboards
for Oil Pressure
oRequires a Digital Pressure Sensor or we offer one at
https://dd-efi.com/collections/accessories
•The 5V Sensor (Red Wire) and Ground Sensor (Black Wire)
get used for all Sensors 1-5 as outlined in the diagram to the
right. Provided is a 2:6 Level Lock Connector to simplify the
wiring process.
•Fuel Level (Yellow Wire) has an internal circuit making the
wiring of your factory vehicle fuel sending unit a single wire
connection. Attach the yellow wire to the fuel level’s signal
wire. Provided T-Tap Wire Connector for easy connection
oDon’t forget to choose the correct fuel level gauge
for your vehicle due to having different empty/full
ohm readings
oDirect connection from the sender; no slosh module

4 | P a g e
Digital Connector
Wiring Video
Link to the Full
DD-EFI Manual
Digital Connector
•(2) PWM Outputs:
oConfigurable for either ON/OFF
oPWM Setup: Extended Control -> PWM Output 1 or 2
oOutputs are low side (Pull to Ground)
oEach capable of up to 6A
•(7) Digital Inputs:
oConfigurable for 12V or GND trigger with internal jumper
oDefault internal jumper set to 12V
oRemoval of the back cover to access jumpers
•Digital Inputs 1, 2 & 3 - pre-configured in DD-EFI Dashboards for
oProvided T-Tap Wire Connector(s) for easy connection
oLeft Signal - Digital Input 1
oRight Signal - Digital Input 2
oHigh Beam –Digital Input 3
•Push Button Start
oSetup: Extended Control -> Push Button Start
oInput Port
▪Select one of the available Digital Inputs
▪This typically comes from the output of the push start button;
the inputs are preconfigured for 12v input.
oOutput Port
▪Select one of the available PWM Outputs
▪These outputs provide a ground signal and are typically wired to
a relay that will provide the 12v to the starter solenoid.
•Examples of other Digital Inputs uses:
oFactory Indicators –High Beam, Low Level Indicators, etc.
oAC Idle Up
oLaunch Control

5 | P a g e
Disclaimer
Digital Dash EFI LLC makes no affiliations, representations, endorsements, sponsorships, or associations
with the Raspberry Pi Foundation or EFI Analytics.
Digital Dash EFI LLC makes no representations or warranties of any type with respect to the contents in
this manual. Digital Dash EFI LLC disclaims any implied warranties or fitness for any particular purpose.
Digital Dash EFI LLC is not liable for any errors contained within or for incidental or consequential damages
in connection with the supply, performance or use of the hardware and software or this manual.
Digital Dash EFI LLC reserves the right to revise this installation and user manual at any time, without
obligation to notify any person of revisions. As defined by the Magnuson-Moss warranty Act, do not install
any products or services unless you have the technical ability to properly set-up the entire vehicle to
compensate for the installation of those products or services. The necessary work and expertise needed
to install different products varies. Instructions, where provided, are given to assist in the installation only;
they are not a substitute for mechanical experience in setting up vehicles. Digital Dash EFI LLC is not
responsible for any personal or property damages caused by the installation of this product.
Warranty
Digital Dash EFI LLC makes every effort to ensure our products and services are of the highest quality and
standards. This warranty applies to the ORIGINAL PURCHASER of this product and covers only those
products exposed to normal use or service. Digital Dash EFI LLC warrants all merchandise manufactured
by Digital Dash EFI LLC against defects in workmanship or material for a period of six (6) months after the
date of purchase. This warranty does not apply to any product that has been damaged through alteration,
improper installation, mishandling, misuse, neglect, or accident. Any part or product found to be
defective after examination by Digital Dash EFI LLC will be repaired or replaced. Digital Dash EFI LLC
assumes no responsibility for loss of time, diagnosis, removal and/or installation labor, loss of vehicle use,
inconvenience or any other consequential expenses.
This Warranty is in lieu of all other expressed warranties or liabilities. Any implied warranties, including
any implied warranty of merchantability, shall be limited to the duration of this written warranty.
If you have any questions regarding warranty, please contact support at Digital Dash EFI LLC at
[email protected].
WARNING: California’s Proposition 65 requires that a clear and visible warning be provided to consumers in California that have
the potential to expose them to various substances which may cause cancer, birth defects or other reproductive harm. Many of
the products of Digital Dash EFI LLC utilizes manufactured products from Aluminum, Plastics, and other standard materials. These
products can expose you to chemicals including lead, which is known to the State of California to cause cancer and birth defects
or other reproductive harm. For more information go to www.P65Warnings.ca.gov