Pro-gard Products LLC. 3SK47UINT16 User manual

STRONG
|
RELIABLE
|
SECURE
INSTALLATION GUIDE
SKID PLATE 3SK47UINT16
2016 - 2019
FORD INTERCEPTOR UTILITY
pro-gard.com
800.480.6680

Page 1 of 1View Graphic
5
/
21
/
201
2
htt
p
s://crs.m
y
mitchell.com/ViewGra
p
hic.as
p
x?
g
uid=10060725.JPG&ds=0&to
p
icid=46&
y
...
I. Refer to the parts list at the end of the page to verify all parts were received.
II. The following tools will be required to complete the installation.
A. 3/8” or 1/2” drive ratchet with 14mm socket, and a 14mm open or box end wrench
IV. Installing the Skid Plate
NOTE: If installing on a Eco-Boost Utility. Remove factory skid plate
and factory skid plate mounting bracket.
A.Remove the 3 (or 5) retainers and remove the underbody air duct
(or optional underbody splash shield). (See Fig. 1)
B. Install the 3SK4716A brackets to the rear 2 holes of the skid plate,
by using the two 3X131 bolts with four 3X121 washers, and two
3SK4716B inserts found in the hardware kit. Slide the inserts into
place over the skid plate into the hole location. Tighten the brackets
to the point that they can still rotate slightly.
C. Install the 3SK4715C brackets to the middle 2 holes of the skid plate,
by using the two 3X131 bolts with four 3X13 washers, and two
3X120 locknuts found in the hardware kit. Tighten the brackets
just to the point that they can still rotate slightly.
D. Hook the mount brackets into the slots on the sub frame and
swing the skid plate up into place, maintaining forward
pressure while performing the next step.
E. Check that the Skid Plate access holes
align with the appropriate engine features. The formed edge
should tuck up behind the radiator support. Now use the supplied
bolts and place two 3X114 in the front 2 holes, two 3X131 into the
middle two holes along with the 8 remaining washers
(3X13) and 4 nuts (3X120).
F. Attach the Skid Plate to the vehicle utilize the OEM anchor points.
(See Fig. 2) Ensure all fasteners are tight (Torque between 35-40 ft lbs). Tighten the fasteners
on the 3SK4715A bracket the rest of the way. Then tighten all remaining fasteners.
Page 1 of 1View Graphic
5
/
21
/
201
2
htt
p
s://crs.m
y
mitchell.com/ViewGra
p
hic.as
p
x?
g
uid=10060495.JPG&ds=0&to
p
icid=40&
y
...
THESE COMPONENTS ARE REQUIRED
TO INSTALL THE PRO-GARD SKID PLATE SYSTEM
pro-gard.com
800.480.6680 2
HARDWARE KIT3SK4716 SKID PLATE
FIG 2
UNDERSIDE OF VEHICLE SHOWN
FIG 1
UNDER BODY SHOWN
o
o
o
o
Mounting Locations
o
o

1 1
2 2
3 3
4 4
A A
B B
C C
D D
Products, LLC
7988 Centerpoint Dr., Suite 400 Indianapolis, IN 46256 [phone]
PART DESCRIPTION:
DRAWN BY:
SCALE:
CHECKED BY:
DATE:
APPROVED:
UNLESS OTHERWISE SPECIFIED :
The information contained herein is proprietary and the property of Pro-gard Products and may not be reproduced, disclosed or used for any other purpose other than a quotation to or an order from Pro-Gard Products without the specific written authorization of Pro-gard Products. Computer Path:
SIZE: A
ENGR 1:
ENGR 3:
ENGR 2:
FINAL:
PRODUCTION:
Third
Angle
Projection
DIMENSIONS ARE IN INCHES
TOL ON 3 PLACE DECIMALS: .005
DIMENSIONS ARE IN INCHESTOL ON ANGLES 1°
TOL ON 2 PLACE DECIMAL .015
NOTE:
MATERIAL:
FINISH:
STAMP:
ASSEMBLY NO: DRAWING NO:
SHEET:
REV:
APPL:
Pro-gard
ROSEN
01/18/2017
SKID PLATE ASSEMBLY & PARTS LIST
2013+ FORD U.I.
3SK4716
1/6 1 OF 7
MUST BE CLEAN AND FREE FROM BURRS
SEE PARTS LIST
PART NUMBER
SEE PARTS LIST
A
V:\All Product Line\Skid Plates\Utility Interceptor\2016\Drawings\3SK4716_RevA
.
PARTS LIST
FINISHMATERIALDESCRIPTIONPART NUMBERQTYITEM
POWDER COAT BLACKSTEEL, 12 GA HRPOSKID PLATE3SK471611
POWDER COAT BLACKSTEELMOUNTING BRACKET3SK4716A22 POWDER COAT BLACK
STEELTHREADED INSERT
3SK4716B23
POWDER COAT BLACKSTEELHANGER BRACKET3SK4716C2
4
YELLOW ZINCSTEEL
3/8-16x2.75, HEX HD CAP SCREW, GR 8, YZ
3X1142
5
YELLOW ZINCSTEEL
3/8-16, Hex Nylon Insert Locknuts, Grade 8, YZ
3X12086
YELLOW ZINCSTEEL
3/8 FLAT WSHR, YZ
3X1316
7
YELLOW ZINCSTEEL
3/8-16X1, HEX HD CAP SCREW, GR8, YZ
3X13188
6
8
7
5
REVISION HISTORY
REV SHEET DESCRIPTION DATE AUTHOR APPROVED
00 ALL NEW RELEASE 01/19/2017 ROSEN
A 1 SUBSTITUTE 3X121 FOR LARGER O.D. 3X13 02/03/2017 ROSEN
2
13
4