DeBug ADB400 Operator's manual

1
BEACH
WHEELCHAIR
MANUAL AND SAFETY INSTRUCTIONS

2
Usage and Safety Information 3
Assembly/Disassembly of DeBug Beach Wheel Chair 4
General Maintenance Instructions 4
General Specifications and Warranty 5
We build the DeBug Beach Wheelchair with the highest quality materials,
keeping in mind the comfort and positioning of the rider.
If any repairs should be required, please do not attempt them without
proper technical training. Please contact your nearest distributor for any
repairs, or adjustments needed
All information in this manual is subject to change without prior notice. Please
read the following few pages for Assembly and Maintenance Instructions.
Thank-you
The De-Bug Mobility Products Team
We love to hear and see how much you are enjoying your Debug Beach
Wheelchair. Feel free to email us any pictures or videos, or post them to our
facebook page
Thanks for your purchase of the
DeBug Beach Wheelchair
TABLE OF CONTENTS

3USAGE & SAFETY
DeBug Beach Wheelchair should not be used during inclement weather,
dangerous surf, rough ocean currents, rip tides and any other poor conditions.
The DeBug is not intended to be used in the water. It is not a flotation device!
We recommended the chair be used only when a lifeguard is present. Safety
comes first!
Users must always be accompanied by a responsible, able-bodied adult.
Always maintain control of your DeBug while in use. When the DeBug is
not in use, the safety brakes must be engaged to prevent the chair from
moving unexpectedly.
The DeBug was built to not tip over, even when used over uneven surfaces.
However, to ensure safety and prevent injury, the user must always wear the
seatbelt while using the DeBug. This is imperative to the user’s safety.
Do not use the components of the DeBug Beach Wheelchair for any purpose
other than what is intended. Do not have more than one person using the DeBug.
Safety Warning
Using your DeBug Beach Wheelchair
Genel Maintenance
It’s so easy to maintain your DeBug Beach Wheelchair! Just follow these simple
instructions, and you will be able to enjoy your chair year after year.
Rinse the chair off with clean water to remove any sand or debris after each use.
The sling material is removable and machine washable.
Check tire pressure before each use. These wheels are meant to be pliable and
somewhat “soft” to the touch. Recommended tire pressure is 2.5 to 4 PSI. These
specifications are molded on each wheel.
If at any time you need to lubricate any part of the chair, DO NOT USE WD-40,
as it will attract dirt and sand, causing possible damage to the wheel bearing/
bushings. We recommend P.T.F.E Dry Lube, on all wearing components. This dry
film is a superior lubricant and repels debris and water, marine and performance
parts stores likely stock this locally.
Have any questions, or need additional support? Please don’t hesitate to
contact us!
Phone [phone] | Email [email protected]

4ASSEMBLY COMPONENTS
Click here to view a video on assembling the DeBug Beach Wheelchair
5/16”-18tp x 2-1/4” SS REAR
SUSPENSION BOLT
1/4”-20tp x 1-1/4” SS
BACKREST BOLT (2 EACH)
1/4”-20tp x 2-1/2” SS MAIN
AXLE BOLT (2 EACH)
5/16” LEG REST
ADJUSTMENT KNOB (2 EACH)
1” SS MAIN AXLE FLAT
WASHER (2 EACH)
1/8” SS MAIN AXLE
HITCH PIN (2 EACH)
REMOVABLE ARMREST
OPTIONAL DRINK HOLDER
LEG REST
ADJUSTMENT KNOBS
1/4”-20 x 1-1/4” S.S. HEX BOLT
2 EACH FOR BACKREST OR
OPTIONAL 1/4” QUICK
RELEASE PIN
5/16”-18 x 2-1/4” S.S. HEX BOLT
1 EACH FOR REAR SUSPENSION
OR 6/16” QUICK RELEASE
PIN OPTION
1/4”-20 x 2-1/2” S.S. HEX BOLT
2 EACH FOR MAIN AXLE
ASSEMBLING INSTRUCTIONS
1. Slide on the leg support sling, and install
the two 5/16”-18 adjustment knobs
2. Slide on the foot plate, and tighten the leg
rest adjustment knobs
3. Install the mid axle, tighten the two
attaching 1/4”-20 bolts
4. To install the backrest, slide the backrest
down on the chair frame and attach using
the two 1/4”-20 bolts
5. The rear suspension may be attached by
inserting the rear suspension tension bolt.
This bolt should be tight during use.
DISASSEMBLING INSTRUCTIONS
1. Loosen the leg length adjustment knobs
and slide out the footplate
2. Slide off the leg support sling by removing
the two 5/16”-18 adjustment knobs
3. To remove the mid axle, loosen the two
attaching 1/4”-20 bolts
4. To remove the backrest, remove the two
attaching 1/4”-20 bolts and slide up on
the backrest
5. The rear suspension may be detached by
removing the rear suspension tension bolt.
This bolt should be tight during use

55 GENERAL SPECIFICATIONS AND
WARRANTY INFORMATION
DEBUG MOBILITY PRODUCTS
850.478.5765
BEACHWHEELCHAIR.COM
SPEC ENGLISH (INCH) METRIC (CM)
Overall height (adjustable) 44”-65” 112 cm-165 cm
Width 33.5 85 cm
Weight 40 lbs 18 kg
Weight Capacity 350 lbs 160 kg
The DeBug Beach Wheelchair frame is constructed using #316L stainless steel
tubing, which is a higher grade than standard #304 marine grade stainless.
The rear caster wheels rotate 360 degrees. The wheel hubs are made from
polynylon material to eliminate saltwater corrosion.
The DeBug has a footrest for proper foot support.
Wheel Lock –Adjustable tension wheel brake can be actuated independently on
each side.
10-Year
Components
& Frame #316L
series stainless
steel The higher
the number the
higher quality
of stainless.
2-Year
Non-absorbent, durable U.V.
resistant Phiffertex Plus brand
nylon seating-material. Removable
and machine washable seating.
3-ply polyurethane tires, designed
to smoothly roll across sand, dirt,
grass and other uneven terrain
30-Day
30 DAY
Money Back
Guarantee
Warnties