decakila KUMG003B User manual

KUMG003B
FOOD PROCESSOR
0
1P
1600 MAX
1400
1200
1000
800
600
200
400
ml
2

IMPORTANT SAFEGUARDS
KNOW YOUR FOOD PROCESSOR
HOUSEHOLD USE ONLY
BEFORE FIRST USE
BLENDING
CHOPPING
CLEANING
SLICING/CHIPPING/SHREDDING
ENVIRONMENT FRIENDLY DISPOSAL
01
03
03
03
04
05
07
07
10
CONTENTS

01
IMPORTANT SAFEGUARDS
Before using the electrical appliance, the following basic precautions should always be followed including the following:
Read all instructions, and save it for future reference.
Before using, check that the voltage of wall outlet corresponds to that shown on the rating plate.
Do not operate any appliance with a damaged cord or plug or aer the appliance malfunctions, or is dropped or damaged in any
manner. Bring it to a qualied technician for examination, repair or electrical or mechanical adjustment.
Do not let cord hang over edge of table or counter.
To protect against risk of electrical shock, do not put the motor base into water or other liquid. To disconnect, turn any control to
“o”, then remove plug from wall outlet by grasping the plug, not the cord.
Close supervision is necessary when any appliance is used by or near children.
Keep hands and utensils away from moving blades or discs while processing food to reduce the risk of severe injury to persons or
damage to the Food Processor. A scraper or spatula may be used, but must be used only when the Food Processor is not running.
Avoid contacting moving parts.
Never feed food by hand. Always use food pusher.
Before removing the lid from the jar from the power unit, switch o the unit, wait until the blades have come to a complete stop.
Do not use ngers to scrape food away from discharge disc while appliance is operating. Cut type injury may result.
Be certain lid is securely locked into place before operating appliance.
Be sure to switch off the appliance after each use of your food processor. Make sure the motor stops completely before
disassembling.
Do not put your ngers or other objects into the unit opening while it is in operation. If food becomes lodged in opening, use food
pusher or another piece of fruit or vegetable to push it down. When this method is not possible, turn the motor o and disassemble
to remove the remaining food.
Do not attempt to defeat the cover interlock mechanism.

02
The metal blades and disk is extremely sharp, handle with care. Always hold the blade assembly by the nger grip or stem, away
from the cutting edge, both when handling and cleaning.
To reduce the risk of injury, never place processing blade or circle blade ass’y on drive sha without the processing jar locked
properly in place.
Do not leave this appliance unattended during use.
If this appliance falls or accidentally becomes immersed in water, unplug it immediately. Do not reach into the water! Do not use
this appliance aer it has fallen into or becomes immersed in water.
To reduce the risk of injury to persons or property, never use this appliance in an unstable position.
Do not use this appliance for other than its intended use.
The use of attachments not recommended or sold by the manufacturer may cause re, electric shock or injury.
Switch o the appliance and disconnect from supply before changing accessories or approaching parts that move in use.
Always disconnect the appliance from the supply if it is le unattended and before assembling, disassembling or cleaning.
Do not use outdoors.
Unplug from outlet when not in use, before putting on or taking o parts, and before cleaning.
If the supply cord is damaged, it must be replaced by the manufacturer, its service agent
or similarly qualied persons in order to avoid a hazard.
Caution: never immerse in water, unplug before inserting or removing parts.
Caution: do not open lid until blades stop.
Appliances can be used by persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if
they have been given supervision or instruction concerning use of the appliance in a safe way and if they understand the hazards
involved. Children shall not play with the appliance.
This appliance shall not be used by children. Keep the appliance and its cord out of reach of children.
Do not ll the bowl above the marked maximum ll line (or rated capacity) to avoid risk of injury due to damage to the cover or
bowl.
Save these instructions.

03
KNOW YOUR FOOD PROCESSOR HOUSEHOLD USE ONLY
POLARIZED PLUG
This appliance has polarized plug(one blade is wider than the
other) . To reduce the risk of electric shock, this plug is intended
to t into a polarized outlet only one way. If the plug does not
fit fully into the outlet, reverse the plug, If it still does not fit,
contact a qualied electrician. Do not attempt to modify in any
way.
BEFORE FIRST USE
Before first use, carefully unpack the food processor and its
attachments and remove any package material or label or
stickers. Clean all the parts except the motor base following the
instructions in CLEANING AND MAINTENANCE. Handle the “S”
blade or circle blade ass’y with extreme care as they are sharp.
The food processor can be used for kneading, beating and
whisking, chopping the meat or vegetable and fruit, shredding,
slicing and chipping the vegetables or potatoes, blending the
smooth soup, sauces, creams, fruit purees, milk and so on,
using dierent accessory to perform dierent task.

04
BLENDING
1. Place the blending jar on the Motor Unit from the unlock
position and slightly turn the jar clockwise until the blending jar
locks into the lock position on the motor base. If the blending
jar is not or is badly positioned, the blender will not work.
2. Peeled or cored the fruit or vegetables and then cut it into
small dices, put the food piece into the jar. Usually certain
amount of purified water has to be added to facilitate the
smooth running of appliance. The amount of mixture should
not exceed the max level as indicated on the blending jar.
Note: never use boiling liquids or run the appliance empty.
And the blending jar can not be used for blending meat.
3. Replace the Jar Cover on the jar and ensure that the Jar Cover
can x with the jar securely.
4. You may add ingredient into the jar through the center
opening of Jar Cover during operation, then replace Measuring
Cup if necessary. Let the tabs of Measuring Cup align with the
grooves of Top Cover, put down and turn in clockwise by 90°to
lock it in place, when disassembling, turn the measuring cup in
anti-clockwise by 90°to unlock it.
5. Connect the plug to wall outlet and set Speed Selector to your
desired speed. There are four setting: P, 0, 1, 2. The 1 setting is
the low speed, the 2 setting is the high speed. Turn the selector
to P position and hold it to pulse actuate motor for
delicate chopping. Release it to return the 0 position. The Pulse
mode allows you to create a burst of power for quick, eicient
blending.
Note: The total operating time should not more than 3
minutes.
6. Turn the Speed Selector to 0 Position once the mixture has
been blended to your desired consistency.
7. Remove the blending jar from the Motor Unit (turning the jar
anti-clockwise), carefully take down the Jar Cover, then pour
and serve.
8. The proportion of the Carrots and water is 3:2. Make sure
the quantity of the water shall not be more than the maximum
specied water quantity.

0505
CLEANING
1. Disconnect the power supply before cleaning.
2. Pour a little warm water into the jar, turn and hold the speed
selector to P position for a few seconds.
3. Remove the jar and rinse and rinse under running water.
Remove Jar cover and measuring cup, then immerse the top
cover, measuring cup in water and clean them with a so brush,
nally clean them with dump cloth.
Caution: the blade base can be disassembled for cleaning.
4. Wipe the outside of base with a damp cloth. Never immerse
it in water as electric shock is possible to occur. Then dry
thoroughly. Ensure the interlock area is free of food particles.
CHOPPING
1. Firstly assemble the driving sha into the motor base, make
sure it is clipped into position.
2. Place the chopping jar on the Motor Unit from the unlock
position and slightly turn the chopping jar clockwise until the
chopping jar locks into the lock position on the motor base.
Make sure it is assembled in place correctly, otherwise the
appliance will not operate.
3. Insert the “S” blade into the driving sha in the chopping jar
securely. Make sure it is locked into position.

anti-clockwise away from motor base, and li it o. Empty the
processed food.
CAUTION: The “S” blade is extremely sharp, handle with care.
06
4. Then place the prepared chopping food into the jar. The food
must be cut into small size firstly (such as 2cm*2cm*6cm for
beef). During chopping, you can add food through the feeding
funnel with the pusher, never using food or nger to push the
food into the feeding funnel.
5. Place the lid onto the jar and turn it clockwise until the tab of
the lid clicks into slot in the jar handle. Make sure it is locked in
position correctly, otherwise the appliance will not operate.
6. Connect the appliance to power supply and set Speed
Selector to your desired speed.
7. There are four setting: P, 0, 1, 2. The 1 setting is the low speed,
the 2 setting is the high speed. Turn the selector to P position
and hold it to pulse actuate motor for delicate chopping.
Release it to return the 0 position. The Pulse mode allows you
to create a burst of power for quick, eicient blending. You can
chop up to 400g of following foodstu.
Hard substance: cheese, dried fruits, and certain vegetables
(carrots...)
So substance: certain vegetables (onions…)
Raw and cooked meat (boned and sliced)
CAUTION: The total operating time should not be more than
90 sec.
8. Turn the Speed Selector to “0” position and unplug the
appliance aer chopping. Open the top lid and grasp blade by
its hub and remove. Unlock chopping jar by turning it in

0707
CLEANING
1. Disconnect the power supply before cleaning.
2. Empty the chopping jar, dismantle all detachable parts and
rinse them in warm soapy water. Extreme caution must be taken
when handling blade as it is very sharp. All the accessories
except motor base are dishwasher safe components, but
the temperature setting shall not exceed 70 ℃. Then dry
thoroughly.
3. Wipe the outside of base with damp cloth. Never immerse
it in water as electric shock is possible to occur. Then dry
thoroughly. Ensure the interlock area is free of food particles.
FOR A QUICK WASH UP
Between processing tasks, pour in some water into the
chopping jar, turn and hold the speed selector to P position a
few seconds for quick cleaning.
SLICING/CHIPPING/SHREDDING
1. Firstly assemble the driving sha into the motor base, make
sure it is clipped into position.
2. Place the chopping jar on the Motor Unit from the unlock
position and slightly turn the chopping jar clockwise until the
chopping jar locks into the lock position on the motor base.
Make sure it is assembled in place correctly, otherwise the
appliance will not operate.
3. Fit the shredding blade or slicing blade or chipping blade
(coarse or ne) into the disk stand, place them in the bowl.
NOTE: For assembling, first push in the no block side, then
push in the other side. For disassembling the blade from the
disk stand, first push out one side with no block, then push
out the other side.
4. Place the lid onto the chopping jar and turn it clockwise until
the tab of the lid clicks into slot in the jar handle. Make sure it
is locked in position correctly, otherwise the appliance will not
operate.
5. Turn the speed selector to 1 or 2 setting to start.
Note: the shredding/slicing/chipping disks can slice thickly-
potatoes, onions, carrots…
6. Use the food pusher to feed food into the feeding funnel. The
food shall be cut into proper size to suitable for the feeding
funnel. You can slice/chip up to 1000g of food.
7. Minimum 2 minutes rest period must be maintained after
one operation cycle. At least 30 minutes rest period must be
maintained to let the appliance cool down aer three operation
cycles.
8. Turn the speed selector to “0”position and unplug unit aer
processing. Remove the blade ass’y. Unlock jar by turning it

08
in anti-clockwise away from its base, and lift it off. Empty the
processed food.
CAUTION: The blade is extremely sharp, handle with care.
CLEANING
1. Disconnect the power supply before cleaning.
2. Empty the chopping jar and remove the disk stand from the
bowl, then remove the shredding/slicing/chipping blade from
the disk stand, the pusher from the lid, the lid from the bowl,
then immerse the lid, pusher, chopping jar, disk stand and the
shredding/slicing/chipping blade in water and clean them with
a soft brush. Extreme caution must be taken when handling
blade as they are very sharp.
Note: For disassembling the disks from the disk stand, first
push out one side with no block, then push out the other side.
For assembling, rst push in the no block side, then push in
the other side.
3. Wipe the outside of base with cloth. Never immerse it in water
as electric shock is possible to occur. Then dry thoroughly.
Ensure the interlock area is free of food particles
Note: Some food may discolor the disk stand. This is normal
and will not harm the plastic or eect the avor of food. Rub
with cloth dipped with vegetable oil to remove discoloration.

09
ENVIRONMENT FRIENDLY DISPOSAL
You can help protect the environment!
Please remember to respect the local regulations: hand in the non-working electrical equipments to an appropriate waste disposal
center.

www.decakila.com Global Links Technology Co. Pte. Ltd.
Made in China Jiangsu China. 2021.D01
decakila decakila
User guide